[PATCH v4 2/2] ARM: dts: imx: add CX9020 Embedded PC device tree
Patrick Brünn
P.Bruenn at beckhoff.com
Tue Jul 25 04:41:56 PDT 2017
>From: Shawn Guo [mailto:shawnguo at kernel.org]
>On Fri, Jul 21, 2017 at 06:06:40AM +0200, linux-kernel-dev at beckhoff.com
>wrote:
>> From: Patrick Bruenn <p.bruenn at beckhoff.com>
>>
>> The CX9020 differs from i.MX53 Quick Start Board by:
>> - use uart2 instead of uart1
>> - DVI-D connector instead of VGA
>> - no audio
>> - no SATA connector
>> - CCAT FPGA connected to emi
>> - enable rtc
>>
>> Signed-off-by: Patrick Bruenn <p.bruenn at beckhoff.com>
>
>Where is the patch 1/2?
>
You can find a copy here [1], or wait for the next revision, I will try to improve my git send-mail skills until then.
I used git send-email with "--to-cmd ./scripts/get_maintainer.pl" to send the series. I just
discovered it would have been better to use To: and Cc: in the cover letter and send with
"--to-cover --cc-cover".
I will drop "--in-reply-to" for the next revision, too...
Is there something like patman [2] from the u-boot project for the kernel, that I am missing?
>>
>> ---
>>
>> v4:
>> - move alternative UART2 pinmux settings to imx53-pinfunc.h
>> - fix copyright notice and model name to clearify cx9020 is a
>> Beckhoff board and not from Freescale/NXP/Qualcomm
>> - add "bhf,cx9020" compatible
>> - remove ccat node and pin configuration as long as the ccat
>> driver is not mainlined
>> - use dvi-connector + ti,tfp410 instead of panel-simple
>> - add newlines between property list and child nodes
>> - replace underscores in node names with hypens
>> - replace magic number 0 with polarity defines from
>> include/dt-bindings/gpio/gpio.h
>> - move rtc node into imx53.dtsi, change it's name into 'srtc',
>> to avoid a conflict with 'rtc' node in imx53-m53.dtsi
>> - rename regulator-3p2v
>> - drop imx53-qsb container node
>> - make iomux configuration explicit
>> - remove unused audmux
>> - remove unused led_pin_gpio3_23 configuration
>> - use blue gpio-leds as disk-activity indicators for mmc0 and mmc1
>> - add mmc indicator leds to sdhc pingroups
>> - keep node names in alphabetical order
>> - remove unused sata and ssi2
>> - remove unused pin configs from hoggrp
>> - add entry for imx53-cx9020.dts to MAINTAINERS
>>
>> v3: add missig changelog
>> v2:
>> - keep alphabetic order of dts/Makefile
>> - configure uart2 with 'fsl,dte-mode'
>> - use display-0 and panel-0 as node names
>> - remove unnecessary "simple-bus" for fixed regulators
>>
>> Cc: Andrew Lunn <andrew at lunn.ch>
>> ---
>> MAINTAINERS | 1 +
>
>I do not take the changes on this file.
>
Do you mean you keep maintainership for imx53-cx9020.dts, or do you
mean I should group it in the patch which adds imx53-cx9020.dts?
I am fine with both and would be glad to have your guidance. I just
didn't understand clearly what was meant.
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/imx53-cx9020.dts | 295
>+++++++++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/imx53-pinfunc.h | 4 +
>> arch/arm/boot/dts/imx53.dtsi | 9 ++
>
>Please have separate patches for imx53-pinfunc.h and imx53.dtsi. Do not
>mix them up with board support dts changes.
>
Okay, I will split it into three patches?
1. Adding SRTC to imx53.dtsi
2. Adding UART2 pinmux settings to imx53-pinfunc.h
3. Adding CX9020 board support
>> 5 files changed, 310 insertions(+)
>> create mode 100644 arch/arm/boot/dts/imx53-cx9020.dts
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 1bf282843dc2..1bd06328f79b 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -1176,6 +1176,7 @@ ARM/BECKHOFF SUPPORT
>> M: Patrick Bruenn <p.bruenn at beckhoff.com>
>> S: Maintained
>> F: Documentation/devicetree/bindings/arm/bhf.txt
>> +F: arch/arm/boot/dts/imx53-cx9020.dts
>>
>> ARM/CALXEDA HIGHBANK ARCHITECTURE
>> M: Rob Herring <robh at kernel.org>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 4b17f35dc9a7..f0ba9be523e0 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -340,6 +340,7 @@ dtb-$(CONFIG_SOC_IMX51) += \
>> imx51-ts4800.dtb
>> dtb-$(CONFIG_SOC_IMX53) += \
>> imx53-ard.dtb \
>> + imx53-cx9020.dtb \
>> imx53-m53evk.dtb \
>> imx53-mba53.dtb \
>> imx53-qsb.dtb \
>> diff --git a/arch/arm/boot/dts/imx53-cx9020.dts
>b/arch/arm/boot/dts/imx53-cx9020.dts
>> new file mode 100644
>> index 000000000000..c4f9c89668c2
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/imx53-cx9020.dts
>> @@ -0,0 +1,295 @@
>> +/*
>> + * Copyright 2017 Beckhoff Automation GmbH & Co. KG
>> + * based on imx53-qsb.dts
>> + *
>> + * The code contained herein is licensed under the GNU General Public
>> + * License. You may obtain a copy of the GNU General Public License
>> + * Version 2 or later at the following locations:
>> + *
>> + * http://www.opensource.org/licenses/gpl-license.html
>> + * http://www.gnu.org/copyleft/gpl.html
>> + */
>> +
>> +/dts-v1/;
>> +#include "imx53.dtsi"
>> +
>> +/ {
>> + model = "Beckhoff CX9020 Embedded PC";
>> + compatible = "bhf,cx9020", "fsl,imx53";
>> +
>> + chosen {
>> + stdout-path = &uart2;
>> + };
>> +
>> + memory {
>> + reg = <0x70000000 0x20000000>,
>> + <0xb0000000 0x20000000>;
>> + };
>> +
>> + display-0 {
>> + #address-cells =<1>;
>> + #size-cells = <0>;
>> + compatible = "fsl,imx-parallel-display";
>> + interface-pix-fmt = "rgb24";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_ipu_disp0>;
>> + status = "okay";
>
>This status line is not necessary. We usually use "okay" to toggle the
>status which is set "disabled" in <soc>.dtsi.
>
I will drop it in v5
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + display0_in: endpoint {
>> + remote-endpoint = <&ipu_di0_disp0>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + display0_out: endpoint {
>> + remote-endpoint = <&tfp410_in>;
>> + };
>> + };
>> + };
>> +
>> + dvi-connector {
>> + compatible = "dvi-connector";
>> + ddc-i2c-bus = <&i2c2>;
>> + digital;
>> +
>> + port {
>> + dvi_connector_in: endpoint {
>> + remote-endpoint = <&tfp410_out>;
>> + };
>> + };
>> + };
>> +
>> + dvi-converter {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "ti,tfp410";
>> +
>> + port at 0 {
>> + reg = <0>;
>> +
>> + tfp410_in: endpoint {
>> + remote-endpoint = <&display0_out>;
>> + };
>> + };
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + tfp410_out: endpoint {
>> + remote-endpoint = <&dvi_connector_in>;
>> + };
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + pwr-r {
>> + gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + pwr-g {
>> + gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
>> + default-state = "on";
>> + };
>> +
>> + pwr-b {
>> + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
>> + default-state = "off";
>> + };
>> +
>> + sd1-b {
>> + linux,default-trigger = "mmc0";
>> + gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + sd2-b {
>> + linux,default-trigger = "mmc1";
>> + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
>> + };
>> + };
>> +
>> + regulator-3p2v {
>> + compatible = "regulator-fixed";
>> + regulator-name = "3P2V";
>> + regulator-min-microvolt = <3200000>;
>> + regulator-max-microvolt = <3200000>;
>> + regulator-always-on;
>> + };
>> +
>> + reg_usb_vbus: regulator {
>
>The node name "regulator" is too generic. The "regulator-vbus"
>might be the one you want to use.
>
Okay, I will call it " regulator-vbus" in the next version
>Shawn
>
Thanks a lot for your time and patience,
Patrick
[1] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1450310.html
[2] http://git.denx.de/?p=u-boot.git;a=blob;f=tools/patman/README
Beckhoff Automation GmbH & Co. KG | Managing Director: Dipl. Phys. Hans Beckhoff
Registered office: Verl, Germany | Register court: Guetersloh HRA 7075
More information about the linux-arm-kernel
mailing list