[PATCH v2 2/4] thermal: add brcmstb AVS TMON driver
Markus Mayer
code at mmayer.net
Fri Jul 21 12:27:33 PDT 2017
From: Brian Norris <computersforpeace at gmail.com>
The AVS TMON core provides temperature readings, a pair of configurable
high- and low-temperature threshold interrupts, and an emergency
over-temperature chip reset. The driver utilizes the first two to
provide temperature readings and high-temperature notifications to
applications. The over-temperature reset is not exposed to
applications; this reset threshold is critical to the system and should
be set with care within the bootloader.
Applications may choose to utilize the notification mechanism, the
temperature reading mechanism (e.g., through polling), or both.
Signed-off-by: Brian Norris <computersforpeace at gmail.com>
Signed-off-by: Doug Berger <opendmb at gmail.com>
Signed-off-by: Markus Mayer <mmayer at broadcom.com>
---
drivers/thermal/Kconfig | 2 +-
drivers/thermal/broadcom/Kconfig | 7 +
drivers/thermal/broadcom/Makefile | 1 +
drivers/thermal/broadcom/brcmstb_thermal.c | 386 +++++++++++++++++++++++++++++
4 files changed, 395 insertions(+), 1 deletion(-)
create mode 100644 drivers/thermal/broadcom/brcmstb_thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index b5b5fac..396ad6b 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -408,7 +408,7 @@ config MTK_THERMAL
controller present in Mediatek SoCs
menu "Broadcom thermal drivers"
-depends on ARCH_BCM || COMPILE_TEST
+depends on ARCH_BCM || ARCH_BRCMSTB || COMPILE_TEST
source "drivers/thermal/broadcom/Kconfig"
endmenu
diff --git a/drivers/thermal/broadcom/Kconfig b/drivers/thermal/broadcom/Kconfig
index 42c098e..c106a15 100644
--- a/drivers/thermal/broadcom/Kconfig
+++ b/drivers/thermal/broadcom/Kconfig
@@ -6,6 +6,13 @@ config BCM2835_THERMAL
help
Support for thermal sensors on Broadcom bcm2835 SoCs.
+config BRCMSTB_THERMAL
+ tristate "Broadcom STB AVS TMON thermal driver"
+ depends on ARCH_BRCMSTB || COMPILE_TEST
+ help
+ Enable this driver if you have a Broadcom STB SoC and would like
+ thermal framework support.
+
config BCM_NS_THERMAL
tristate "Northstar thermal driver"
depends on ARCH_BCM_IPROC || COMPILE_TEST
diff --git a/drivers/thermal/broadcom/Makefile b/drivers/thermal/broadcom/Makefile
index c6f62e4..fae10ec 100644
--- a/drivers/thermal/broadcom/Makefile
+++ b/drivers/thermal/broadcom/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
+obj-$(CONFIG_BRCMSTB_THERMAL) += brcmstb_thermal.o
obj-$(CONFIG_BCM_NS_THERMAL) += ns-thermal.o
diff --git a/drivers/thermal/broadcom/brcmstb_thermal.c b/drivers/thermal/broadcom/brcmstb_thermal.c
new file mode 100644
index 0000000..eae89af
--- /dev/null
+++ b/drivers/thermal/broadcom/brcmstb_thermal.c
@@ -0,0 +1,386 @@
+/*
+ * Broadcom STB AVS TMON thermal sensor driver
+ *
+ * Copyright (c) 2015-2017 Broadcom
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#define DRV_NAME "brcmstb_thermal"
+
+#define pr_fmt(fmt) DRV_NAME ": " fmt
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/irqreturn.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+
+#define AVS_TMON_STATUS 0x00
+ #define AVS_TMON_STATUS_valid_msk BIT(11)
+ #define AVS_TMON_STATUS_data_msk GENMASK(10, 1)
+ #define AVS_TMON_STATUS_data_shift 1
+
+#define AVS_TMON_EN_OVERTEMP_RESET 0x04
+ #define AVS_TMON_EN_OVERTEMP_RESET_msk BIT(0)
+
+#define AVS_TMON_RESET_THRESH 0x08
+ #define AVS_TMON_RESET_THRESH_msk GENMASK(10, 1)
+ #define AVS_TMON_RESET_THRESH_shift 1
+
+#define AVS_TMON_INT_IDLE_TIME 0x10
+
+#define AVS_TMON_EN_TEMP_INT_SRCS 0x14
+ #define AVS_TMON_EN_TEMP_INT_SRCS_high BIT(1)
+ #define AVS_TMON_EN_TEMP_INT_SRCS_low BIT(0)
+
+#define AVS_TMON_INT_THRESH 0x18
+ #define AVS_TMON_INT_THRESH_high_msk GENMASK(26, 17)
+ #define AVS_TMON_INT_THRESH_high_shift 17
+ #define AVS_TMON_INT_THRESH_low_msk GENMASK(10, 1)
+ #define AVS_TMON_INT_THRESH_low_shift 1
+
+#define AVS_TMON_TEMP_INT_CODE 0x1c
+#define AVS_TMON_TP_TEST_ENABLE 0x20
+
+/* Default coefficients */
+#define AVS_TMON_TEMP_SLOPE -487
+#define AVS_TMON_TEMP_OFFSET 410040
+
+/* HW related temperature constants */
+#define AVS_TMON_TEMP_MAX 0x3ff
+#define AVS_TMON_TEMP_MIN -88161
+#define AVS_TMON_TEMP_MASK AVS_TMON_TEMP_MAX
+
+enum avs_tmon_trip_type {
+ TMON_TRIP_TYPE_LOW = 0,
+ TMON_TRIP_TYPE_HIGH,
+ TMON_TRIP_TYPE_RESET,
+ TMON_TRIP_TYPE_MAX,
+};
+
+struct avs_tmon_trip {
+ /* HW bit to enable the trip */
+ u32 enable_offs;
+ u32 enable_mask;
+
+ /* HW field to read the trip temperature */
+ u32 reg_offs;
+ u32 reg_msk;
+ int reg_shift;
+};
+
+static struct avs_tmon_trip avs_tmon_trips[] = {
+ /* Trips when temperature is below threshold */
+ [TMON_TRIP_TYPE_LOW] = {
+ .enable_offs = AVS_TMON_EN_TEMP_INT_SRCS,
+ .enable_mask = AVS_TMON_EN_TEMP_INT_SRCS_low,
+ .reg_offs = AVS_TMON_INT_THRESH,
+ .reg_msk = AVS_TMON_INT_THRESH_low_msk,
+ .reg_shift = AVS_TMON_INT_THRESH_low_shift,
+ },
+ /* Trips when temperature is above threshold */
+ [TMON_TRIP_TYPE_HIGH] = {
+ .enable_offs = AVS_TMON_EN_TEMP_INT_SRCS,
+ .enable_mask = AVS_TMON_EN_TEMP_INT_SRCS_high,
+ .reg_offs = AVS_TMON_INT_THRESH,
+ .reg_msk = AVS_TMON_INT_THRESH_high_msk,
+ .reg_shift = AVS_TMON_INT_THRESH_high_shift,
+ },
+ /* Automatically resets chip when above threshold */
+ [TMON_TRIP_TYPE_RESET] = {
+ .enable_offs = AVS_TMON_EN_OVERTEMP_RESET,
+ .enable_mask = AVS_TMON_EN_OVERTEMP_RESET_msk,
+ .reg_offs = AVS_TMON_RESET_THRESH,
+ .reg_msk = AVS_TMON_RESET_THRESH_msk,
+ .reg_shift = AVS_TMON_RESET_THRESH_shift,
+ },
+};
+
+struct brcmstb_thermal_priv {
+ void __iomem *tmon_base;
+ struct device *dev;
+ struct thermal_zone_device *thermal;
+};
+
+static void avs_tmon_get_coeffs(struct thermal_zone_device *tz, int *slope,
+ int *offset)
+{
+ *slope = thermal_zone_get_slope(tz);
+ *offset = thermal_zone_get_offset(tz);
+}
+
+/* Convert a HW code to a temperature reading (millidegree celsius) */
+static inline int avs_tmon_code_to_temp(struct thermal_zone_device *tz,
+ u32 code)
+{
+ const int val = code & AVS_TMON_TEMP_MASK;
+ int slope, offset;
+
+ avs_tmon_get_coeffs(tz, &slope, &offset);
+
+ return slope * val + offset;
+}
+
+/*
+ * Convert a temperature value (millidegree celsius) to a HW code
+ *
+ * @temp: temperature to convert
+ * @low: if true, round toward the low side
+ */
+static inline u32 avs_tmon_temp_to_code(struct thermal_zone_device *tz,
+ int temp, bool low)
+{
+ int slope, offset;
+
+ if (temp < AVS_TMON_TEMP_MIN)
+ return AVS_TMON_TEMP_MAX; /* Maximum code value */
+
+ avs_tmon_get_coeffs(tz, &slope, &offset);
+
+ if (temp >= offset)
+ return 0; /* Minimum code value */
+
+ if (low)
+ return (u32)(DIV_ROUND_UP(offset - temp, abs(slope)));
+ else
+ return (u32)((offset - temp) / abs(slope));
+}
+
+static int brcmstb_get_temp(void *data, int *temp)
+{
+ struct brcmstb_thermal_priv *priv = data;
+ u32 val;
+ long t;
+
+ val = __raw_readl(priv->tmon_base + AVS_TMON_STATUS);
+
+ if (!(val & AVS_TMON_STATUS_valid_msk)) {
+ dev_err(priv->dev, "reading not valid\n");
+ return -EIO;
+ }
+
+ val = (val & AVS_TMON_STATUS_data_msk) >> AVS_TMON_STATUS_data_shift;
+
+ t = avs_tmon_code_to_temp(priv->thermal, val);
+ if (t < 0)
+ *temp = 0;
+ else
+ *temp = t;
+
+ return 0;
+}
+
+static void avs_tmon_trip_enable(struct brcmstb_thermal_priv *priv,
+ enum avs_tmon_trip_type type, int en)
+{
+ struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+ u32 val = __raw_readl(priv->tmon_base + trip->enable_offs);
+
+ pr_debug("%sable trip, type %d\n", en ? "en" : "dis", type);
+
+ if (en)
+ val |= trip->enable_mask;
+ else
+ val &= ~trip->enable_mask;
+
+ __raw_writel(val, priv->tmon_base + trip->enable_offs);
+}
+
+static int avs_tmon_get_trip_temp(struct brcmstb_thermal_priv *priv,
+ enum avs_tmon_trip_type type)
+{
+ struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+ u32 val = __raw_readl(priv->tmon_base + trip->reg_offs);
+
+ val &= trip->reg_msk;
+ val >>= trip->reg_shift;
+
+ return avs_tmon_code_to_temp(priv->thermal, val);
+}
+
+static void avs_tmon_set_trip_temp(struct brcmstb_thermal_priv *priv,
+ enum avs_tmon_trip_type type,
+ int temp)
+{
+ struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+ u32 val, orig;
+
+ pr_debug("set temp %d to %d\n", type, temp);
+
+ /* round toward low temp for the low interrupt */
+ val = avs_tmon_temp_to_code(priv->thermal, temp,
+ type == TMON_TRIP_TYPE_LOW);
+
+ val <<= trip->reg_shift;
+ val &= trip->reg_msk;
+
+ orig = __raw_readl(priv->tmon_base + trip->reg_offs);
+ orig &= ~trip->reg_msk;
+ orig |= val;
+ __raw_writel(orig, priv->tmon_base + trip->reg_offs);
+}
+
+static int avs_tmon_get_intr_temp(struct brcmstb_thermal_priv *priv)
+{
+ u32 val;
+
+ val = __raw_readl(priv->tmon_base + AVS_TMON_TEMP_INT_CODE);
+ return avs_tmon_code_to_temp(priv->thermal, val);
+}
+
+static irqreturn_t brcmstb_tmon_irq_thread(int irq, void *data)
+{
+ struct brcmstb_thermal_priv *priv = data;
+ int low, high, intr;
+
+ low = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_LOW);
+ high = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_HIGH);
+ intr = avs_tmon_get_intr_temp(priv);
+
+ dev_dbg(priv->dev, "low/intr/high: %d/%d/%d\n",
+ low, intr, high);
+
+ /* Disable high-temp until next threshold shift */
+ if (intr >= high)
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
+ /* Disable low-temp until next threshold shift */
+ if (intr <= low)
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
+
+ /*
+ * Notify using the interrupt temperature, in case the temperature
+ * changes before it can next be read out
+ */
+ thermal_zone_device_update(priv->thermal, intr);
+
+ return IRQ_HANDLED;
+}
+
+static int brcmstb_set_trips(void *data, int low, int high)
+{
+ struct brcmstb_thermal_priv *priv = data;
+
+ pr_debug("set trips %d <--> %d\n", low, high);
+
+ if (low) {
+ if (low > INT_MAX)
+ low = INT_MAX;
+ avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_LOW, low);
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 1);
+ } else {
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
+ }
+
+ if (high < ULONG_MAX) {
+ if (high > INT_MAX)
+ high = INT_MAX;
+ avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_HIGH, high);
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 1);
+ } else {
+ avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
+ }
+
+ return 0;
+}
+
+static struct thermal_zone_of_device_ops of_ops = {
+ .get_temp = brcmstb_get_temp,
+ .set_trips = brcmstb_set_trips,
+};
+
+static const struct of_device_id brcmstb_thermal_id_table[] = {
+ { .compatible = "brcm,avs-tmon" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, brcmstb_thermal_id_table);
+
+static int brcmstb_thermal_probe(struct platform_device *pdev)
+{
+ struct thermal_zone_device *thermal;
+ struct brcmstb_thermal_priv *priv;
+ struct resource *res;
+ int irq, ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->tmon_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->tmon_base))
+ return PTR_ERR(priv->tmon_base);
+
+ priv->dev = &pdev->dev;
+ platform_set_drvdata(pdev, priv);
+
+ thermal = thermal_zone_of_sensor_register(&pdev->dev, 0, priv, &of_ops);
+ if (IS_ERR(thermal)) {
+ ret = PTR_ERR(thermal);
+ dev_err(&pdev->dev, "could not register sensor: %d\n", ret);
+ return ret;
+ }
+
+ priv->thermal = thermal;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "could not get IRQ\n");
+ ret = irq;
+ goto err;
+ }
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ brcmstb_tmon_irq_thread, IRQF_ONESHOT,
+ DRV_NAME, priv);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "could not request IRQ: %d\n", ret);
+ goto err;
+ }
+
+ dev_info(&pdev->dev, "registered AVS TMON of-sensor driver\n");
+
+ return 0;
+
+err:
+ thermal_zone_of_sensor_unregister(&pdev->dev, thermal);
+ return ret;
+}
+
+static int brcmstb_thermal_exit(struct platform_device *pdev)
+{
+ struct brcmstb_thermal_priv *priv = platform_get_drvdata(pdev);
+ struct thermal_zone_device *thermal = priv->thermal;
+
+ if (thermal)
+ thermal_zone_of_sensor_unregister(&pdev->dev, priv->thermal);
+
+ return 0;
+}
+
+static struct platform_driver brcmstb_thermal_driver = {
+ .probe = brcmstb_thermal_probe,
+ .remove = brcmstb_thermal_exit,
+ .driver = {
+ .name = DRV_NAME,
+ .of_match_table = brcmstb_thermal_id_table,
+ },
+};
+module_platform_driver(brcmstb_thermal_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Brian Norris");
+MODULE_DESCRIPTION("Broadcom STB AVS TMON thermal driver");
--
2.7.4
More information about the linux-arm-kernel
mailing list