[linux-sunxi] [PATCH 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64

[Chen-Yu Tsai]

On Fri, Jul 21, 2017 at 7:07 AM, Icenowy Zheng <icenowy at aosc.io> wrote:
> Banana Pi M64 board uses an AXP803 PMIC.
>
> Enable the PMIC and its regulators.
>
> As we have now proper regulators support, missing or dummy regulators
> are changed to the correct ones.
>
> Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
> ---
>  .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 116 +++++++++++++++++++--
>  1 file changed, 106 insertions(+), 10 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> index 829922d077fb..51d67c0a0edf 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
> @@ -58,13 +58,6 @@
>         chosen {
>                 stdout-path = "serial0:115200n8";
>         };
> -
> -       reg_vcc3v3: vcc3v3 {
> -               compatible = "regulator-fixed";
> -               regulator-name = "vcc3v3";
> -               regulator-min-microvolt = <3300000>;
> -               regulator-max-microvolt = <3300000>;
> -       };
>  };
>
>  &ehci1 {
> @@ -76,6 +69,7 @@
>         pinctrl-0 = <&rgmii_pins>;
>         phy-mode = "rgmii";
>         phy-handle = <&ext_rgmii_phy>;
> +       phy-supply = <&reg_dc1sw>;
>         status = "okay";
>  };
>
> @@ -99,7 +93,7 @@
>  &mmc0 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc0_pins>;
> -       vmmc-supply = <&reg_vcc3v3>;
> +       vmmc-supply = <&reg_dcdc1>;
>         cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
>         cd-inverted;
>         disable-wp;
> @@ -110,7 +104,8 @@
>  &mmc1 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc1_pins>;
> -       vmmc-supply = <&reg_vcc3v3>;
> +       vmmc-supply = <&reg_dldo2>;
> +       vqmmc-supply = <&reg_dldo4>;
>         bus-width = <4>;
>         non-removable;
>         status = "okay";
> @@ -119,7 +114,7 @@
>  &mmc2 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc2_pins>;
> -       vmmc-supply = <&reg_vcc3v3>;
> +       vmmc-supply = <&reg_dcdc1>;
>         bus-width = <8>;
>         non-removable;
>         cap-mmc-hw-reset;
> @@ -130,6 +125,107 @@
>         status = "okay";
>  };
>
> +&r_rsb {
> +       status = "okay";
> +
> +       axp803: pmic at 3a3 {
> +               compatible = "x-powers,axp803";
> +               reg = <0x3a3>;
> +               interrupt-parent = <&r_intc>;
> +               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +       };
> +};
> +
> +#include "axp803.dtsi"
> +
> +&reg_aldo2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-pl";
> +};
> +
> +&reg_aldo3 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3000000>;
> +       regulator-max-microvolt = <3000000>;
> +       regulator-name = "vcc-pll-avcc";
> +};
> +
> +&reg_dc1sw {
> +       regulator-name = "vcc-phy";
> +};
> +
> +&reg_dcdc1 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-3v3";
> +};
> +
> +&reg_dcdc2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1000000>;

The datasheet says the minimum voltage is 1.04V.

> +       regulator-max-microvolt = <1300000>;
> +       regulator-name = "vdd-cpux";
> +};
> +
> +/* DCDC3 is polyphased with DCDC2 */
> +
> +&reg_dcdc5 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1500000>;
> +       regulator-max-microvolt = <1500000>;
> +       regulator-name = "vcc-dram";
> +};
> +
> +&reg_dcdc6 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1100000>;
> +       regulator-max-microvolt = <1100000>;
> +       regulator-name = "vdd-sys";
> +};
> +
> +&reg_dldo1 {
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-hdmi-dsi";
> +};
> +
> +&reg_dldo2 {
> +       regulator-min-microvolt = <3300000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-wifi";
> +};
> +
> +&reg_dldo4 {
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <3300000>;
> +       regulator-name = "vcc-wifi-io";
> +};
> +
> +&reg_eldo1 {
> +       regulator-min-microvolt = <1800000>;
> +       regulator-max-microvolt = <1800000>;
> +       regulator-name = "cpvdd";
> +};
> +

It looks like you are missing a few regulators? I assume you
would add them once the peripherals that use them are added?

Otherwise this patch looks good.

ChenYu

> +/*
> + * The A64 chip cannot work without this regulator off, although
> + * it seems to be only driving the AR100 core.
> + * Maybe we don't still know well about CPUs domain.
> + */
> +&reg_fldo2 {
> +       regulator-always-on;
> +       regulator-min-microvolt = <1100000>;
> +       regulator-max-microvolt = <1100000>;
> +       regulator-name = "vdd-cpus";
> +};
> +
> +&reg_rtc_ldo {
> +       regulator-name = "vcc-rtc";
> +};
> +
>  &uart0 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&uart0_pins_a>;
> --
> 2.13.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.