[PATCH 11/18] dt-bindings: display: Add Allwinner MIPI-DSI bindings

[Maxime Ripard]

Hi Rob,

On Mon, Jul 17, 2017 at 01:41:49PM -0500, Rob Herring wrote:
> On Thu, Jul 13, 2017 at 04:13:06PM +0200, Maxime Ripard wrote:
> > The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
> > ---
> >  Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 85 +++++++-
> >  1 file changed, 85 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > new file mode 100644
> > index 000000000000..2e7c5aa7020f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > @@ -0,0 +1,85 @@
> > +Allwinner A31 DSI Encoder
> > +=========================
> > +
> > +The DSI pipeline consists of two separate blocks: the DSI controller
> > +itself, and its associated D-PHY.
> > +
> > +DSI Encoder
> > +-----------
> > +
> > +The DSI Encoder generates the DSI signal from the TCON's.
> > +
> > +Required properties:
> > +  - compatible: value must be one of:
> > +    * allwinner,sun6i-a31-mipi-dsi
> > +  - reg: base address and size of memory-mapped region
> > +  - interrupts: interrupt associated to this IP
> > +  - clocks: phandles to the clocks feeding the DSI encoder
> > +    * bus: the DSI interface clock
> > +    * mod: the DSI module clock
> > +  - clock-names: the clock names mentioned above
> > +  - phys: phandle to the D-PHY
> > +  - phy-names: must be "dphy"
> > +  - resets: phandle to the reset controller driving the encoder
> > +
> > +  - ports: A ports node with endpoint definitions as defined in
> > +    Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > +    port should be the input endpoint, usually coming from the
> > +    associated TCON.
> 
> Output port for bridge/panel?

The DSI panels and bridges are subnodes of the DSI controller. But I
should mention that :)

> 
> > +
> > +D-PHY
> > +-----
> > +
> > +Required properties:
> > +  - compatible: value must be one of:
> > +    * allwinner,sun6i-a31-mipi-dphy
> > +  - reg: base address and size of memory-mapped region
> > +  - clocks: phandles to the clocks feeding the DSI encoder
> > +    * bus: the DSI interface clock
> > +    * mod: the DSI module clock
> > +  - clock-names: the clock names mentioned above
> > +  - resets: phandle to the reset controller driving the encoder
> > +
> > +Example:
> > +
> > +dsi0: dsi at 01ca0000 {
> 
> Drop the leading 0.
> 
> > +	compatible = "allwinner,sun6i-a31-mipi-dsi";
> > +	reg = <0x01ca0000 0x1000>;
> > +	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> > +	clocks = <&ccu CLK_BUS_MIPI_DSI>,
> > +		 <&ccu CLK_DSI_SCLK>;
> > +	clock-names = "bus", "mod";
> > +	resets = <&ccu RST_BUS_MIPI_DSI>;
> > +	phys = <&dphy0>;
> > +	phy-names = "dphy";
> 
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> 
> Not needed.
> 
> > +
> > +	ports {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		dsi0_in: port at 0 {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			reg = <0>;
> > +
> > +			dsi0_in_tcon0: endpoint at 0 {
> > +				reg = <0>;
> 
> Don't need reg when there's only 1 endpoint.
> 
> > +				remote-endpoint = <&tcon0_out_dsi0>;
> > +			};
> > +		};
> > +	};
> > +};
> > +
> > +dphy0: d-phy at 01ca1000 {
> 
> Drop leading 0.
> 
> > +	compatible = "allwinner,sun6i-a31-mipi-dphy";
> > +	reg = <0x01ca1000 0x1000>;
> > +	clocks = <&ccu CLK_BUS_MIPI_DSI>,
> > +		 <&ccu CLK_DSI_DPHY>;
> > +	clock-names = "bus", "mod";
> > +	resets = <&ccu RST_BUS_MIPI_DSI>;
> 
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> 
> For what?

I'll address those comments, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170720/4baa0f70/attachment.sig>