[linux-sunxi] [PATCH v5 2/6] clk: sunxi-ng: Add sun4i/sun7i CCU driver

[Olliver Schinagl]

Hey Priit,

On 07/13/17 21:23, Priit Laes wrote:
> On Mon, Jul 10, 2017 at 11:45:32AM +0200, Olliver Schinagl wrote:
>> Hi Pleas,
>>
>> again, but this time with content :)
>>
>> On 04-07-17 22:04, Priit Laes wrote:
>>> Introduce a clock controller driver for sun4i A10 and sun7i A20
>>> series SoCs.
> [ ... ]
>
>>> +++ b/drivers/clk/sunxi-ng/Kconfig
>>> @@ -11,6 +11,19 @@ config SUN50I_A64_CCU
>>> 	default ARM64 && ARCH_SUNXI
>>> 	depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
>>>
>>> +config SUNXI_A10_CCU
>> I understand why you say sunXi here (it's support for both sun4i and sun7i)
>> but then why A10, as it also supports the A20.
>>
>> I guess the CCU is identical on the A20 and the A10, right? Thus would it
>> not be sensible to just call it sun4i_ccu (like we do for sun5i_ccu below?
> No, it's not identical.
But then saying SUNXI_A10_CCU is not correct? Since it is not identical
on the A20? So what does the A10 stand for?
>
>>> +	bool "Support for the Allwinner A10/A20 CCU"
>>> +	select SUNXI_CCU_DIV
>>> +	select SUNXI_CCU_MULT
>>> +	select SUNXI_CCU_NK
>>> +	select SUNXI_CCU_NKM
>>> +	select SUNXI_CCU_NM
>>> +	select SUNXI_CCU_MP
>>> +	select SUNXI_CCU_PHASE
>>> +	default MACH_SUN4I
>>> +	default MACH_SUN7I
>>> +	depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST
>>> +
>>> config SUN5I_CCU
>>> 	bool "Support for the Allwinner sun5i family CCM"
>>> 	default MACH_SUN5I
>>> @@ -57,4 +70,5 @@ config SUN8I_R_CCU
>>> 	bool "Support for Allwinner SoCs' PRCM CCUs"
>>> 	default MACH_SUN8I || (ARCH_SUNXI && ARM64)
>>>
>>> +
>> oops?
> OK
>
>>> new file mode 100644
>>> index 0000000..49052b7
>>> --- /dev/null
>>> +++ b/drivers/clk/sunxi-ng/ccu-sun4i-a10.c
>> <snip>
>>
>>> +static const char *const apb1_parents[] = { "hosc", "pll-periph", "osc32k" };
>>> +static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", apb1_parents, 0x058,
>>> +			     0, 5,	/* M */
>>> +			     16, 2,	/* P */
>>> +			     24, 2,	/* mux */
>>> +			     0);
>>> +
>>> +/* Not present on A20 */
>>> +static SUNXI_CCU_GATE(axi_dram_clk,	"axi-dram",	"ahb",
>>> +		      0x05c, BIT(31), 0);
>> Same here I guess, two defines make this a bit more readable.
> You mean SUN4I_CCU_GATE? and SUN7I_CCU_GATE defines?
> I don't think it makes things more readable...
you think 0x05c and BIT(31) are easier to read? I'll do a pop quiz in 6
months from now and see if you remember :p
>
>>> +
>>> +static SUNXI_CCU_GATE(ahb_otg_clk,	"ahb-otg",	"ahb",
> ...
>>> +		      0x060, BIT(14), CLK_IS_CRITICAL);
>> <snip>
>>
>>> +static struct ccu_reset_map sun7i_a20_ccu_resets[] = {
>>> +	[RST_USB_PHY0]		= { 0x0cc, BIT(0) },
>>> +	[RST_USB_PHY1]		= { 0x0cc, BIT(1) },
>>> +	[RST_USB_PHY2]		= { 0x0cc, BIT(2) },
>>> +	[RST_GPS]		= { 0x0d0, BIT(0) },
>>> +	[RST_DE_BE0]		= { 0x104, BIT(30) },
>>> +	[RST_DE_BE1]		= { 0x108, BIT(30) },
>>> +	[RST_DE_FE0]		= { 0x10c, BIT(30) },
>>> +	[RST_DE_FE1]		= { 0x110, BIT(30) },
>>> +	[RST_DE_MP]		= { 0x114, BIT(30) },
>>> +	[RST_TCON0]		= { 0x118, BIT(30) },
>>> +	[RST_TCON1]		= { 0x11c, BIT(30) },
>> You are missing the TV encoder reset:
>> +      [RST_TVE0]              = { 0x118, BIT(29) },
>> +      [RST_TVE1]              = { 0x11c, BIT(29) },
>>
>> (to match your table i did not use defines :p)
> Where did you get this information?
> This is not present in any datasheets I have:
>   * A10 - 1.50
>   * A20 - 1.4
It is actually from the A13. In the A13 all the other bits match up. We
know from both that TCON0 is at 0x118 with its reset at BIT(30) and
TCON1 has its reset 0x11c. From the A13 datasheet we gather that TCON(0)
and TV(0) are at 0x118 with RST_TV on BIT(31) and thus it is only
logical that that for the TVE1 we have the rest at 0x11c.

But this is writing from the top of my head, I think we can also find it
in the 3.4 sources if I recall correctly.
>
> [...]
>
> Päikest,
> Priit Laes