[PATCH v3 06/12] mfd: wm97xx-core: core support for wm97xx Codec
Charles Keepax
ckeepax at opensource.cirrus.com
Mon Jul 3 02:08:40 PDT 2017
On Fri, Jun 30, 2017 at 09:44:02PM +0200, Robert Jarzmik wrote:
> The WM9705, WM9712 and WM9713 are highly integrated codecs, with an
> audio codec, DAC and ADC, GPIO unit and a touchscreen interface.
>
> Historically the support was spread across drivers/input/touchscreen and
> sound/soc/codecs. The sharing was done through ac97 bus sharing. This
> model will not withstand the new AC97 bus model, where codecs are
> discovered on runtime.
>
> Signed-off-by: Robert Jarzmik <robert.jarzmik at free.fr>
> ---
> drivers/mfd/Kconfig | 14 +++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/wm97xx-core.c | 282 +++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/wm97xx.h | 31 +++++
> 4 files changed, 328 insertions(+)
> create mode 100644 drivers/mfd/wm97xx-core.c
> create mode 100644 include/linux/mfd/wm97xx.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb74d31..440677bac5c9 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1628,6 +1628,20 @@ config MFD_WM8994
> core support for the WM8994, in order to use the actual
> functionaltiy of the device other drivers must be enabled.
>
> +config MFD_WM97xx
> + tristate "Wolfson Microelectronics WM97xx"
> + select MFD_CORE
> + select REGMAP_AC97
> + select AC97_BUS_COMPAT if AC97_BUS_NEW
> + help
> +
> + The WM9705, WM9712 and WM9713 is a highly integrated hi-fi CODEC
> + designed for smartphone applications. As well as audio functionality
> + it has on board GPIO and a touchscreen functionality which is
> + supported via the relevant subsystems. This driver provides core
> + support for the WM97xx, in order to use the actual functionaltiy of
> + the device other drivers must be enabled.
> +
> config MFD_STW481X
> tristate "Support for ST Microelectronics STw481x"
> depends on I2C && (ARCH_NOMADIK || COMPILE_TEST)
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 31ce07611a6f..902c2e46f310 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -69,6 +69,7 @@ obj-$(CONFIG_MFD_WM8350) += wm8350.o
> obj-$(CONFIG_MFD_WM8350_I2C) += wm8350-i2c.o
> wm8994-objs := wm8994-core.o wm8994-irq.o wm8994-regmap.o
> obj-$(CONFIG_MFD_WM8994) += wm8994.o
> +obj-$(CONFIG_MFD_WM97xx) += wm97xx-core.o
>
> obj-$(CONFIG_TPS6105X) += tps6105x.o
> obj-$(CONFIG_TPS65010) += tps65010.o
> diff --git a/drivers/mfd/wm97xx-core.c b/drivers/mfd/wm97xx-core.c
> new file mode 100644
> index 000000000000..0813fc9fa8ed
> --- /dev/null
> +++ b/drivers/mfd/wm97xx-core.c
> @@ -0,0 +1,282 @@
> +/*
> + * Wolfson WM97xx -- Core device
> + *
> + * Copyright (C) 2016 Robert Jarzmik
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Features:
> + * - an AC97 audio codec
> + * - a touchscreen driver
> + * - a GPIO block
> + */
> +
> +#include <linux/module.h>
> +
> +#include <linux/device.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/wm97xx.h>
> +#include <linux/wm97xx.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <sound/ac97/codec.h>
> +#include <sound/ac97/compat.h>
> +
> +#define WM9705_VENDOR_ID 0x574d4c05
> +#define WM9712_VENDOR_ID 0x574d4c12
> +#define WM9713_VENDOR_ID 0x574d4c13
> +#define WM97xx_VENDOR_ID_MASK 0xffffffff
> +
> +struct wm97xx_priv {
> + struct regmap *regmap;
> + struct snd_ac97 *ac97;
> + struct device *dev;
> +};
> +
> +static bool wm97xx_readable_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case AC97_RESET ... AC97_PCM_SURR_DAC_RATE:
> + case AC97_PCM_LR_ADC_RATE:
> + case AC97_CENTER_LFE_MASTER:
> + case AC97_SPDIF ... AC97_LINE1_LEVEL:
> + case AC97_GPIO_CFG ... 0x5c:
> + case AC97_CODEC_CLASS_REV ... AC97_PCI_SID:
> + case 0x74 ... AC97_VENDOR_ID2:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static bool wm97xx_writeable_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case AC97_VENDOR_ID1:
> + case AC97_VENDOR_ID2:
> + return false;
> + default:
> + return wm97xx_readable_reg(dev, reg);
> + }
> +}
> +
> +static const struct reg_default wm97xx_reg_defaults[] = {
> +};
Should we not have some defaults in here?
> +
> +static const struct regmap_config wm9705_regmap_config = {
> + .reg_bits = 16,
> + .reg_stride = 2,
> + .val_bits = 16,
> + .max_register = 0x7e,
> + .cache_type = REGCACHE_RBTREE,
> +
> + .reg_defaults = wm97xx_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(wm97xx_reg_defaults),
> + .volatile_reg = regmap_ac97_default_volatile,
> + .readable_reg = wm97xx_readable_reg,
> + .writeable_reg = wm97xx_writeable_reg,
> +};
> +
> +static const struct regmap_config wm9712_regmap_config = {
> + .reg_bits = 16,
> + .reg_stride = 2,
> + .val_bits = 16,
> + .max_register = 0x7e,
> + .cache_type = REGCACHE_RBTREE,
> +
> + .reg_defaults = wm97xx_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(wm97xx_reg_defaults),
> + .volatile_reg = regmap_ac97_default_volatile,
> + .readable_reg = wm97xx_readable_reg,
> + .writeable_reg = wm97xx_writeable_reg,
> +};
> +
> +static int wm9705_register(struct wm97xx_priv *wm97xx)
> +{
> + return 0;
> +}
> +
> +static int wm9712_register(struct wm97xx_priv *wm97xx)
> +{
> + return 0;
> +}
> +
So are we only adding stubs for the 9705 and 9712? If so we
should probably make that clear in the commit message at least.
> +static const struct reg_default wm9713_reg_defaults[] = {
> + { 0x02, 0x8080 }, /* Speaker Output Volume */
> + { 0x04, 0x8080 }, /* Headphone Output Volume */
> + { 0x06, 0x8080 }, /* Out3/OUT4 Volume */
> + { 0x08, 0xc880 }, /* Mono Volume */
> + { 0x0a, 0xe808 }, /* LINEIN Volume */
> + { 0x0c, 0xe808 }, /* DAC PGA Volume */
> + { 0x0e, 0x0808 }, /* MIC PGA Volume */
> + { 0x10, 0x00da }, /* MIC Routing Control */
> + { 0x12, 0x8000 }, /* Record PGA Volume */
> + { 0x14, 0xd600 }, /* Record Routing */
> + { 0x16, 0xaaa0 }, /* PCBEEP Volume */
> + { 0x18, 0xaaa0 }, /* VxDAC Volume */
> + { 0x1a, 0xaaa0 }, /* AUXDAC Volume */
> + { 0x1c, 0x0000 }, /* Output PGA Mux */
> + { 0x1e, 0x0000 }, /* DAC 3D control */
> + { 0x20, 0x0f0f }, /* DAC Tone Control*/
> + { 0x22, 0x0040 }, /* MIC Input Select & Bias */
> + { 0x24, 0x0000 }, /* Output Volume Mapping & Jack */
> + { 0x26, 0x7f00 }, /* Powerdown Ctrl/Stat*/
> + { 0x28, 0x0405 }, /* Extended Audio ID */
> + { 0x2a, 0x0410 }, /* Extended Audio Start/Ctrl */
> + { 0x2c, 0xbb80 }, /* Audio DACs Sample Rate */
> + { 0x2e, 0xbb80 }, /* AUXDAC Sample Rate */
> + { 0x32, 0xbb80 }, /* Audio ADCs Sample Rate */
> + { 0x36, 0x4523 }, /* PCM codec control */
> + { 0x3a, 0x2000 }, /* SPDIF control */
> + { 0x3c, 0xfdff }, /* Powerdown 1 */
> + { 0x3e, 0xffff }, /* Powerdown 2 */
> + { 0x40, 0x0000 }, /* General Purpose */
> + { 0x42, 0x0000 }, /* Fast Power-Up Control */
> + { 0x44, 0x0080 }, /* MCLK/PLL Control */
> + { 0x46, 0x0000 }, /* MCLK/PLL Control */
> +
> + { 0x4c, 0xfffe }, /* GPIO Pin Configuration */
> + { 0x4e, 0xffff }, /* GPIO Pin Polarity / Type */
> + { 0x50, 0x0000 }, /* GPIO Pin Sticky */
> + { 0x52, 0x0000 }, /* GPIO Pin Wake-Up */
> + /* GPIO Pin Status */
> + { 0x56, 0xfffe }, /* GPIO Pin Sharing */
> + { 0x58, 0x4000 }, /* GPIO PullUp/PullDown */
> + { 0x5a, 0x0000 }, /* Additional Functions 1 */
> + { 0x5c, 0x0000 }, /* Additional Functions 2 */
> + { 0x60, 0xb032 }, /* ALC Control */
> + { 0x62, 0x3e00 }, /* ALC / Noise Gate Control */
> + { 0x64, 0x0000 }, /* AUXDAC input control */
> + { 0x74, 0x0000 }, /* Digitiser Reg 1 */
> + { 0x76, 0x0006 }, /* Digitiser Reg 2 */
> + { 0x78, 0x0001 }, /* Digitiser Reg 3 */
> + { 0x7a, 0x0000 }, /* Digitiser Read Back */
> +};
> +
> +static const struct regmap_config wm9713_regmap_config = {
> + .reg_bits = 16,
> + .reg_stride = 2,
> + .val_bits = 16,
> + .max_register = 0x7e,
> + .cache_type = REGCACHE_RBTREE,
> +
> + .reg_defaults = wm9713_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(wm9713_reg_defaults),
> + .volatile_reg = regmap_ac97_default_volatile,
> + .readable_reg = wm97xx_readable_reg,
> + .writeable_reg = wm97xx_writeable_reg,
> +};
> +
> +static int wm9713_register(struct wm97xx_priv *wm97xx,
> + struct wm97xx_pdata *pdata)
> +{
> + static struct wm97xx_platform_data codec_pdata;
> + static const struct mfd_cell cells[] = {
> + {
> + .name = "wm9713-codec",
> + .platform_data = &codec_pdata,
> + .pdata_size = sizeof(codec_pdata),
> + },
> + {
> + .name = "wm97xx-ts",
> + .platform_data = &codec_pdata,
> + .pdata_size = sizeof(codec_pdata),
> + },
> + };
> +
> + codec_pdata.ac97 = wm97xx->ac97;
> + codec_pdata.regmap = devm_regmap_init_ac97(wm97xx->ac97,
> + &wm9713_regmap_config);
> + codec_pdata.batt_pdata = pdata->batt_pdata;
> + if (IS_ERR(codec_pdata.regmap))
> + return PTR_ERR(codec_pdata.regmap);
> +
> + return devm_mfd_add_devices(wm97xx->dev, -1, cells,
Should probably use the define PLATFORM_DEVID_NONE here.
> + ARRAY_SIZE(cells), NULL, 0, NULL);
> +}
> +
> +static int wm97xx_ac97_probe(struct ac97_codec_device *adev)
> +{
> + struct wm97xx_priv *wm97xx;
> + int ret;
> + void *pdata = snd_ac97_codec_get_platdata(adev);
> +
> + wm97xx = devm_kzalloc(ac97_codec_dev2dev(adev),
> + sizeof(*wm97xx), GFP_KERNEL);
> + if (!wm97xx)
> + return -ENOMEM;
> +
> + wm97xx->dev = ac97_codec_dev2dev(adev);
> + wm97xx->ac97 = snd_ac97_compat_alloc(adev);
> + if (IS_ERR(wm97xx->ac97))
> + return PTR_ERR(wm97xx->ac97);
> +
> +
> + ac97_set_drvdata(adev, wm97xx);
> + dev_info(wm97xx->dev, "wm97xx core found, id=0x%x\n",
> + adev->vendor_id);
> +
> + switch (adev->vendor_id) {
> + case WM9705_VENDOR_ID:
> + ret = wm9705_register(wm97xx);
> + break;
> + case WM9712_VENDOR_ID:
> + ret = wm9712_register(wm97xx);
> + break;
> + case WM9713_VENDOR_ID:
> + ret = wm9713_register(wm97xx, pdata);
> + break;
> + default:
> + ret = -ENODEV;
> + }
> +
> + if (ret)
> + snd_ac97_compat_release(wm97xx->ac97);
> +
> + return ret;
> +}
> +
> +static int wm97xx_ac97_remove(struct ac97_codec_device *adev)
> +{
> + struct wm97xx_priv *wm97xx = ac97_get_drvdata(adev);
> +
> + snd_ac97_compat_release(wm97xx->ac97);
> +
> + return 0;
> +}
> +
> +static const struct ac97_id wm97xx_ac97_ids[] = {
> + { .id = WM9705_VENDOR_ID, .mask = WM97xx_VENDOR_ID_MASK },
> + { .id = WM9712_VENDOR_ID, .mask = WM97xx_VENDOR_ID_MASK },
> + { .id = WM9713_VENDOR_ID, .mask = WM97xx_VENDOR_ID_MASK },
> + { }
> +};
> +
> +static struct ac97_codec_driver wm97xx_ac97_driver = {
> + .driver = {
> + .name = "wm97xx-core",
> + },
> + .probe = wm97xx_ac97_probe,
> + .remove = wm97xx_ac97_remove,
> + .id_table = wm97xx_ac97_ids,
> +};
> +
> +static int __init wm97xx_module_init(void)
> +{
> + return snd_ac97_codec_driver_register(&wm97xx_ac97_driver);
> +}
> +module_init(wm97xx_module_init);
> +
> +static void __exit wm97xx_module_exit(void)
> +{
> + snd_ac97_codec_driver_unregister(&wm97xx_ac97_driver);
> +}
> +module_exit(wm97xx_module_exit);
> +
> +MODULE_DESCRIPTION("WM9712, WM9713 core driver");
> +MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik at free.fr>");
> +MODULE_LICENSE("GPL");
> +
> diff --git a/include/linux/mfd/wm97xx.h b/include/linux/mfd/wm97xx.h
> new file mode 100644
> index 000000000000..627322f14d48
> --- /dev/null
> +++ b/include/linux/mfd/wm97xx.h
> @@ -0,0 +1,31 @@
> +/*
> + * wm97xx client interface
> + *
> + * Copyright (C) 2016 Robert Jarzmik
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef __LINUX_MFD_WM97XX_H
> +#define __LINUX_MFD_WM97XX_H
> +
> +struct regmap;
> +struct wm97xx_batt_pdata;
> +struct snd_ac97;
> +
> +struct wm97xx_platform_data {
> + struct snd_ac97 *ac97;
> + struct regmap *regmap;
> + struct wm97xx_batt_pdata *batt_pdata;
> +};
> +
> +
> +#endif
> --
> 2.11.0
Other than those minor comments looks ok to me.
Thanks,
Charles
More information about the linux-arm-kernel
mailing list