[PATCH 2/2] ARM: dts: Qualcomm APQ8060 DragonBoard ALS sensor

[Linus Walleij]

This adds the Capella CM3605 ambient light and proximity sensor
to the APQ8060 DragonBoard device tree. Notice that we also set
up pin config for the AOUT line and GPIO lines, and that we set
the default trigger on the infrared LED to associate with the
"cm3605" trigger so the IR LED is controlled by this the CM3605
driver.

Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
Andy: these bindings have been merged to the IIO tree and ACKed
by DT maintainers.
---
 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 53 ++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index c04960371c5e..f3bd65e284ee 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -23,6 +23,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include "qcom-msm8660.dtsi"
 
 / {
@@ -83,6 +84,25 @@
 		};
 	};
 
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* GPIO34 has interrupt 225 on the PM8058 */
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058 225 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&xoadc 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+
 	soc {
 		pinctrl at 800000 {
 			/* eMMMC pins, all 8 data lines connected */
@@ -317,6 +337,24 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
+					dragon_cm3605_gpios: cm3605-gpios {
+						/* Pin 34 connected to the proxy IRQ */
+						pinconf_gpio34 {
+							pins = "gpio34";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+						/* Pin 35 connected to ASET */
+						pinconf_gpio35 {
+							pins = "gpio35";
+							function = "normal";
+							output-high;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
 					dragon_veth_gpios: veth-gpios {
 						pinconf {
 							pins = "gpio40";
@@ -327,6 +365,20 @@
 					};
 				};
 
+				mpps at 50 {
+					dragon_cm3605_mpps: cm3605-mpps {
+						pinconf {
+							pins = "mpp5";
+							function = "analog";
+							input-enable;
+							bias-high-impedance;
+							/* Let's use channel 5 */
+							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+				};
+
 				xoadc at 197 {
 					/* Reference voltage 2.2 V */
 					xoadc-ref-supply = <&pm8058_l18>;
@@ -367,6 +419,7 @@
 					reg = <0x48>;
 					label = "pm8058:infrared:proximitysensor";
 					default-state = "off";
+					linux,default-trigger = "cm3605";
 				};
 				led at 131 {
 					compatible = "qcom,pm8058-led";
-- 
2.9.3