[PATCH 2/8] serial: st-asc: Provide RTS functionality

[Lee Jones]

Until this point, it has not been possible for userland serial
applications (e.g. stty) to toggle the UART RTS line.  This can
be useful with certain configurations. For example, when using
a Mezzanine on a Linaro 96board, RTS line is used to take the
on-board microcontroller in and out of reset.

Signed-off-by: Lee Jones <lee.jones at linaro.org>
---
 drivers/tty/serial/st-asc.c | 27 +++++++++++++++++++++++----
 1 file changed, 23 insertions(+), 4 deletions(-)

diff --git a/drivers/tty/serial/st-asc.c b/drivers/tty/serial/st-asc.c
index 69e6232..397df50 100644
--- a/drivers/tty/serial/st-asc.c
+++ b/drivers/tty/serial/st-asc.c
@@ -30,6 +30,7 @@
 #include <linux/of_platform.h>
 #include <linux/serial_core.h>
 #include <linux/clk.h>
+#include <linux/gpio/consumer.h>
 
 #define DRIVER_NAME "st-asc"
 #define ASC_SERIAL_NAME "ttyAS"
@@ -38,6 +39,7 @@
 
 struct asc_port {
 	struct uart_port port;
+	struct gpio_desc *rts;
 	struct clk *clk;
 	unsigned int hw_flow_control:1;
 	unsigned int force_m1:1;
@@ -391,12 +393,27 @@ static unsigned int asc_tx_empty(struct uart_port *port)
 
 static void asc_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
+	struct asc_port *ascport = to_asc_port(port);
+
 	/*
-	 * This routine is used for seting signals of: DTR, DCD, CTS/RTS
-	 * We use ASC's hardware for CTS/RTS, so don't need any for that.
-	 * Some boards have DTR and DCD implemented using PIO pins,
-	 * code to do this should be hooked in here.
+	 * This routine is used for seting signals of: DTR, DCD, CTS and RTS.
+	 * We use ASC's hardware for CTS/RTS when hardware flow-control is
+	 * enabled, however if the RTS line is required for another purpose,
+	 * commonly controlled using HUP from userspace, then we need to toggle
+	 * it manually, using GPIO.
+	 *
+	 * Some boards also have DTR and DCD implemented using PIO pins, code to
+	 * do this should be hooked in here.
 	 */
+
+	if (!ascport->rts)
+		return;
+
+	/* If HW flow-control is enabled, we can't fiddle with the RTS line */
+	if (asc_in(port, ASC_CTL) & ASC_CTL_CTSENABLE)
+		return;
+
+	gpiod_set_value(ascport->rts, mctrl & TIOCM_RTS);
 }
 
 static unsigned int asc_get_mctrl(struct uart_port *port)
@@ -726,6 +743,8 @@ static struct asc_port *asc_of_get_asc_port(struct platform_device *pdev)
 							"st,hw-flow-control");
 	asc_ports[id].force_m1 =  of_property_read_bool(np, "st,force_m1");
 	asc_ports[id].port.line = id;
+	asc_ports[id].rts = NULL;
+
 	return &asc_ports[id];
 }
 
-- 
2.10.2