[PATCH V9] thermal: bcm2835: add thermal driver for bcm2835 soc

[Eduardo Valentin]

Hello Martin,

On Fri, Jan 20, 2017 at 09:43:02AM +0100, kernel at martin.sperl.org wrote:
> 
> > On 20.01.2017, at 05:23, Eduardo Valentin <edubezval at gmail.com> wrote:
> > 
> > On Thu, Jan 19, 2017 at 08:14:02PM -0800, Eduardo Valentin wrote:
> >> Hello Martin,
> >> 
> >> On Sat, Jan 07, 2017 at 04:55:45PM +0000, kernel at martin.sperl.org wrote:
> >>> From: Martin Sperl <kernel at martin.sperl.org>
> >>> 
> >>> Add basic thermal driver for bcm2835 SOC.
> >>> 
> >>> This driver currently relies on the firmware setting up the
> >>> tsense HW block and does not set it up itself.
> >>> 
> >>> Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
> >>> Acked-by: Eric Anholt <eric at anholt.net>
> >>> Acked-by: Stefan Wahren <stefan.wahren at i2se.com>
> >>> 
> >> 
> >> <cut>
> > 
> > 
> > Also, I am getting this warn from sparse:
> > drivers/thermal/bcm2835_thermal.c:110:16: warning: cast truncates bits
> > from constant value (3ffffffffff00 becomes ffffff00)
> > drivers/thermal/bcm2835_thermal.c:134:16: warning: cast truncates bits
> > from constant value (3ffffffffff becomes ffffffff)
> > 
> > Have you seen this?
> 
> No, I have not checked sparse.
> 
> These values are defined via GENMASK on line 47 and 57 respectively
> and should actually compute to the following values:
>   for line 110 (line 47 has the define):
>     GENMASK(BCM2835_TS_TSENSCTL_THOLD_BITS +     \
>             BCM2835_TS_TSENSCTL_THOLD_SHIFT - 1, \
>             BCM2835_TS_TSENSCTL_THOLD_SHIFT)
>     = GENMASK(10 + 8 - 1, 8) 
>     = GENMASK(17, 8)
>     = (((~0UL) << (8)) & (~0UL >> (32 - 1 - (10 + 8 - 1))))
>     = 0x3ff00
>   for line 134 (line 57 has the define):
>     GENMASK(BCM2835_TS_TSENSCTL_THOLD_BITS +     \
>             BCM2835_TS_TSENSCTL_THOLD_SHIFT - 1, \
>             BCM2835_TS_TSENSCTL_THOLD_SHIFT)
>     = GENMASK(10 + 0 - 1, 0)
>     = GENMASK(9, 0)
>     = (((~0UL) << (0)) & (~0UL >> (32 - 1 - (10 + 0 - 1))))
>     = 0x003ff
> 
> Note that the preprocessor expansions have been verified by
> looking at the preprocessed driver source
> (drivers/thermal/bcm2835_thermal.i)

OK then.

> 
> I wonder why sparse is computing these GENMASK values as:
> 0x3ffffffffff00 and 0x3ffffffffff

In the case you can confirm that the values are correct, I believe this
could be a false positive report on sparse, in this case.

> 
> Martin