[PATCH v3 16/24] media: Add i.MX media core driver

[Steve Longerbeam]

On 01/23/2017 03:13 AM, Philipp Zabel wrote:
> Hi Steve,
>
> On Sun, 2017-01-22 at 18:31 -0800, Steve Longerbeam wrote:
>> On 01/16/2017 05:47 AM, Philipp Zabel wrote:
>>> On Sat, 2017-01-14 at 14:46 -0800, Steve Longerbeam wrote:
>>> [...]
>>>>>> +Unprocessed Video Capture:
>>>>>> +--------------------------
>>>>>> +
>>>>>> +Send frames directly from sensor to camera interface, with no
>>>>>> +conversions:
>>>>>> +
>>>>>> +-> ipu_smfc -> camif
>>>>> I'd call this capture interface, this is not just for cameras. Or maybe
>>>>> idmac if you want to mirror hardware names?
>>>> Camif is so named because it is the V4L2 user interface for video
>>>> capture. I suppose it could be named "capif", but that doesn't role
>>>> off the tongue quite as well.
>>> Agreed, capif sounds weird. I find camif a bit confusing though, because
>>> Samsung S3C has a camera interface that is actually called "CAMIF".
>> how about simply "capture" ?
> That sounds good to me.

done.

>
>>>>> This should really be handled by v4l2_pipeline_pm_use.
>>>> I thought about this earlier, but v4l2_pipeline_pm_use() seems to be
>>>> doing some other stuff that bothered me, at least that's what I remember.
>>>> I will revisit this.
>>> I have used it with a tc358743 -> mipi-csi2 pipeline, it didn't cause
>>> any problems. It would be better to reuse and, if necessary, fix the
>>> existing infrastructure where available.
>> I tried this API, by switching to v4l2_pipeline_pm_use() in camif
>> open/release,
>> and switched to v4l2_pipeline_link_notify() instead of
>> imx_media_link_notify()
>> in the media driver's media_device_ops.
>>
>> This API assumes the video device has an open file handle while the media
>> links are being established. This doesn't work for me, I want to be able to
>> establish the links using 'media-ctl -l', and that won't work unless
>> there is an
>> open file handle on the video capture device node.
>>
>> Also, I looked into calling v4l2_pipeline_pm_use() during
>> imx_media_link_notify(),
>> instead of imx_media_pipeline_set_power(). Again there are problems with
>> that.
>>
>> First, v4l2_pipeline_pm_use() acquires the graph mutex, so it can't be
>> called inside
>> link_notify which already acquires that lock. The header for this
>> function also
>> clearly states it should only be called in open/release.
> So why not call it in open/release then?

er, see above (?)

>
>> Second, ignoring the above locking issue for a moment,
>> v4l2_pipeline_pm_use()
>> will call s_power on the sensor _first_, then the mipi csi-2 s_power,
>> when executing
>> media-ctl -l '"ov5640 1-003c":0 -> "imx6-mipi-csi2":0[1]'. Which is the
>> wrong order.
>> In my version which enforces the correct power on order, the mipi csi-2
>> s_power
>> is called first in that link setup, followed by the sensor.
> I don't understand why you want to power up subdevs as soon as the links
> are established.

Because that is the precedence, all other media drivers do pipeline
power on/off at link_notify. And v4l2_pipeline_link_notify() was written
as a link_notify method.

>   Shouldn't that rather be done for all subdevices in the
> pipeline when the corresponding capture device is opened?

that won't work. There's no guarantee the links will be established
at capture device open time.

> It seems to me that powering up the pipeline should be the last step
> before userspace actually starts the capture.

Well, I'm ok with moving pipeline power on/off to start/stop streaming.
I would actually prefer to do it then, I only chose at link_notify because
of precedence. I'll look into it.

Steve