[PATCH v2 8/9] ARM: dts: add support for I2SE Duckbill 2 SPI
Michael Heimpold
mhei at heimpold.de
Sun Jan 22 14:22:43 PST 2017
This machine is based on I2SE's Duckbill 2 board and is sold as part of I2SE's
PLC Bundle for IoT. This is a development kit for Homeplug Green PHY based
powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei at heimpold.de>
Cc: Stefan Wahren <stefan.wahren at i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx28-duckbill-2-spi.dts | 199 +++++++++++++++++++++++++++++
2 files changed, 200 insertions(+)
create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d7fcb4dc..d2d2486 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -478,6 +478,7 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-duckbill-2-485.dts \
imx28-duckbill-2.dtb \
imx28-duckbill-2-enocean.dts \
+ imx28-duckbill-2-spi.dts \
imx28-duckbill.dtb \
imx28-eukrea-mbmx283lc.dtb \
imx28-eukrea-mbmx287lc.dtb \
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
new file mode 100644
index 0000000..738eaa7
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -0,0 +1,199 @@
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info at i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei at heimpold.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "I2SE Duckbill 2 SPI";
+ compatible = "i2se,duckbill", "fsl,imx28";
+
+ aliases {
+ ethernet1 = &qca7000;
+ };
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb at 80000000 {
+ apbh at 80000000 {
+ ssp0: ssp at 80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+ non-removable;
+ };
+
+ ssp2: ssp at 80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ qca7000: ethernet at 0 {
+ compatible = "qca,qca7000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qca7000_pins>;
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <8000000>;
+ };
+ };
+
+ pinctrl at 80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_int_pin: mac0-phy-int at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins: led at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20
+ MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ qca7000_pins: qca7000 at 0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
+ MX28_PAD_LCD_D13__GPIO_1_13 /* QCA7K reset */
+ MX28_PAD_LCD_D14__GPIO_1_14 /* GPIO 0 */
+ MX28_PAD_LCD_D15__GPIO_1_15 /* GPIO 1 */
+ MX28_PAD_LCD_D18__GPIO_1_18 /* GPIO 2 */
+ MX28_PAD_LCD_D21__GPIO_1_21 /* GPIO 3 */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+ };
+
+ apbx at 80040000 {
+ lradc at 80050000 {
+ status = "okay";
+ };
+
+ duart: serial at 80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy at 8007c000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb at 80080000 {
+ usb0: usb at 80080000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ };
+
+ mac0: ethernet at 800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+ phy-supply = <®_3p3v>;
+ phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_phy_int_pin>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ status-red {
+ label = "duckbill:red:status";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4
More information about the linux-arm-kernel
mailing list