[PATCH v3 0/9] meson-gx: reset RGMII PHYs and configure TX delay

[Jerome Brunet]

On Fri, 2017-01-20 at 16:22 +0100, Martin Blumenstingl wrote:
> This series adds the reset GPIOs for the (external) ethernet PHYs on
> all
> GXBB boards.
> Additionally it provides a ethernet PHY node which can be used to
> specify
> PHY-specific properties (this may be required if more boards require
> the
> "eee-broken-1000t" for the RTL8211F ethernet PHY). To make all board
> .dts
> consistent I chose to add the PHY node also for boards which don't
> have a
> RTL8211F PHY.
> 
> Patch #7 from this series also removes ethernet support for the P200
> board because it was broken anyways and nobody seems to have a board
> available for testing. This was the outcome of the discussion from
> [0]
> 
> Patch #8 was taken from (older versions of) my other series (see
> [1]):
> "[PATCH net-next v3 0/2] stmmac: dwmac-meson8b: configurable
> RGMII TX delay".
> The binding changes for amlogic,tx-delay-ns were ACK'ed already.
> 
> Changes since v2:
> - fixed patch #2 to really update the P200 board (as it's the P200
> which
>   actually uses a Micrel KSZ9031 RGMII PHY). Thanks to Neil Armstrong
> for
>   spotting this huge mistake!
> - instead of dropping ethernet support for P201 we simply re-
> configure it
>   to RMII mode (replaces patch #7) without a MDIO node (which keeps
> PHY
>   auto-scanning enabled). This got Neil Armstrong's ACK off-list
> already
> 
> Changes since v1:
> - do not move the MDIO bus to meson-gx as this disables PHY auto-
> scanning
>   in the stmmac driver (this drops patch #1 from v1)
> - add the ethernet PHY reset GPIO for nexbox a95x which was forgotten
> in
>   v1
> - add the ethernet PHY reset GPIO for boards which were added since
> v1
>   (wetek hub and wetek play2)
> - rebased to apply against the current v4.11/dt64 branch
> - new in v2 (patch #7): disabled ethernet support for the P200 board
> (see
>   the commit description for more information). this patch is
> optional
> - new in v2 (patch #9): removed the phy-mode property from meson-gx
> (see
>   the commit description for more information). this patch is
> optional
> 
> 
> [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-January/0
> 02053.html
> [1] http://lists.infradead.org/pipermail/linux-amlogic/2016-December/
> 001834.html
> 
> Martin Blumenstingl (9):
>   ARM64: dts: meson-gxbb-odroidc2: add the ethernet PHY's reset GPIO
>   ARM64: dts: meson-gxbb-p200: add the ethernet PHY's reset GPIO
>   ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO
>   ARM64: dts: meson-gxbb-nexbox-a95x: add the ethernet PHY's reset
> GPIO
>   ARM64: dts: meson-gxbb-wetek-hub: add the ethernet PHY's reset GPIO
>   ARM64: dts: meson-gxbb-wetek-play2: add the ethernet PHY's reset
> GPIO
>   ARM64: dts: meson-gxbb-p201: fix ethernet support
>   ARM64: dts: amlogic: add the ethernet TX delay configuration
>   ARM64: dts: meson-gx: remove the phy-mode property from meson-gx
> 
>  arch/arm64/boot/dts/amlogic/meson-gx.dtsi          |  1 -
>  .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts    | 17
> ++++++++++++++
>  .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts |  7 ++++++
>  arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts    | 26
> ++++++++++++++++++++++
>  arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts    | 11 +++++++++
>  arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi   |  6 -----
>  .../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi      | 20
> +++++++++++++++++
>  .../boot/dts/amlogic/meson-gxbb-wetek-hub.dts      | 26
> ++++++++++++++++++++++
>  .../boot/dts/amlogic/meson-gxbb-wetek-play2.dts    | 26
> ++++++++++++++++++++++
>  .../boot/dts/amlogic/meson-gxl-s905d-p230.dts      |  2 ++
>  .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts |  2 ++
>  arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts     |  2 ++
>  12 files changed, 139 insertions(+), 7 deletions(-)

Looks good.

Reviewed-by: Jerome Brunet <jbrunet at baylibre.com>

>