[PATCH 3/3] PCI: imx6: Add code to support i.MX7D

[Andrey Smirnov]

On Thu, Jan 19, 2017 at 8:52 AM, Lucas Stach <l.stach at pengutronix.de> wrote:
> Am Donnerstag, den 19.01.2017, 08:36 -0800 schrieb Andrey Smirnov:
>> Add various bits of code needed to support i.MX7D variant of the IP.
>>
>> Cc: yurovsky at gmail.com
>> Cc: Richard Zhu <hongxing.zhu at nxp.com>
>> Cc: Lucas Stach <l.stach at pengutronix.de>
>> Cc: Bjorn Helgaas <bhelgaas at google.com>
>> Cc: Fabio Estevam <festevam at gmail.com>
>> Cc: Shawn Guo <shawnguo at kernel.org>
>> Cc: Rob Herring <robh+dt at kernel.org>
>> Cc: Mark Rutland <mark.rutland at arm.com>
>> Cc: Lee Jones <lee.jones at linaro.org>
>> Cc: linux-arm-kernel at lists.infradead.org
>> Cc: devicetree at vger.kernel.org
>> Cc: linux-kernel at vger.kernel.org
>> Signed-off-by: Andrey Smirnov <andrew.smirnov at gmail.com>
>> ---
>>  .../devicetree/bindings/pci/fsl,imx6q-pcie.txt     |   6 +-
>>  drivers/pci/host/pci-imx6.c                        | 188 ++++++++++++++++++---
>>  include/linux/mfd/syscon/imx7-gpc.h                |  18 ++
>>  include/linux/mfd/syscon/imx7-iomuxc-gpr.h         |   4 +
>>  include/linux/mfd/syscon/imx7-src.h                |  18 ++
>>  5 files changed, 208 insertions(+), 26 deletions(-)
>>  create mode 100644 include/linux/mfd/syscon/imx7-gpc.h
>>  create mode 100644 include/linux/mfd/syscon/imx7-src.h
>>
>> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
>> index 83aeb1f..20b9382 100644
>> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
>> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
>> @@ -4,7 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP
>>  and thus inherits all the common properties defined in designware-pcie.txt.
>>
>>  Required properties:
>> -- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie"
>> +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie",
>> +           "fsl,imx6qp-pcie", "fsl,imx7d-pcie"
>>  - reg: base address and length of the PCIe controller
>>  - interrupts: A list of interrupt outputs of the controller. Must contain an
>>    entry for each entry in the interrupt-names property.
>> @@ -34,6 +35,9 @@ Additional required properties for imx6sx-pcie:
>>  - clock names: Must include the following additional entries:
>>       - "pcie_inbound_axi"
>>
>> +Additional required properties for imx7d-pcie:
>> +- pcie-phy-supply: Should specify the regulator supplying PCIe PHY
>> +
> This isn't a PHY regulator, but a regulator powering the GPC domain
> where the PHY is located. This should not be handled in the PCIe driver.
> See the previous discussion with i.MX6SX, that is in the same boat.
>

Good to know, thanks for clarification.

> [...]
>>  static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
>>  {
>> -     if (imx6_pcie->variant == IMX6SX)
>> +     switch (imx6_pcie->variant) {
>> +     case IMX7D: {
>> +             int ret;
>> +             unsigned int reg, mapping;
>> +             struct pcie_port *pp = &imx6_pcie->pp;
>> +             struct device *dev = pp->dev;
>> +
>> +             regulator_set_voltage(imx6_pcie->pcie_phy_regulator,
>> +                                   1000000, 1000000);
>> +             ret = regulator_enable(imx6_pcie->pcie_phy_regulator);
>> +             if (ret) {
>> +                     dev_err(dev, "failed to enable pcie regulator.\n");
>> +                     return;
>> +             }
>> +
>> +             /*
>> +              * Now that PHY regulator is enabled, do sofware
>> +              * power-up request by mapping PHY in A7 domain and
>> +              * setting power-up request bit
>> +              */
>> +             regmap_read(imx6_pcie->gpc, GPC_PGC_CPU_MAPPING, &mapping);
>> +             regmap_write(imx6_pcie->gpc, GPC_PGC_CPU_MAPPING,
>> +                          mapping | IMX7D_PCIE_PHY_A7_DOMAIN);
>> +
>> +             regmap_update_bits(imx6_pcie->gpc, GPC_PU_PGC_SW_PUP_REQ,
>> +                                IMX7D_PCIE_PHY_SW_PUP_REQ,
>> +                                IMX7D_PCIE_PHY_SW_PUP_REQ);
>> +             /*
>> +              * As per "5.5.9.4 Example Code 4" in IMX7DRM.pdf wait
>> +              * for PUP_REQ bit to be cleared
>> +              */
>> +             while (!regmap_read(imx6_pcie->gpc,
>> +                                 GPC_PU_PGC_SW_PUP_REQ, &reg) &&
>> +                    reg & IMX7D_PCIE_PHY_SW_PUP_REQ)
>> +                     ;
>> +             regmap_write(imx6_pcie->gpc, GPC_PGC_CPU_MAPPING, mapping);
>
> I won't allow code touching the GPC registers to sneak into the PCIe
> driver. I know this is the downstream solution, but this really needs a
> proper GPC power domain driver, instead of this hack.
>

OK, will change in v2.

> Regards,
> Lucas
>