[PATCH v2 0/9] meson-gx: reset RGMII PHYs and configure TX delay

[Martin Blumenstingl]

This series adds the reset GPIOs for the (external) ethernet PHYs on all
GXBB boards.
Additionally it provides a ethernet PHY node which can be used to specify
PHY-specific properties (this may be required if more boards require the
"eee-broken-1000t" for the RTL8211F ethernet PHY). To make all board .dts
consistent I chose to add the PHY node also for boards which don't have a
RTL8211F PHY.

Patch #7 from this series also removes ethernet support for the P200
board because it was broken anyways and nobody seems to have a board
available for testing. This was the outcome of the discussion from [0]

Patch #8 was taken from (older versions of) my other series (see [1]):
"[PATCH net-next v3 0/2] stmmac: dwmac-meson8b: configurable
RGMII TX delay".
The binding changes for amlogic,tx-delay-ns were ACK'ed already.

Changes since v1:
- do not move the MDIO bus to meson-gx as this disables PHY auto-scanning
  in the stmmac driver (this drops patch #1 from v1)
- add the ethernet PHY reset GPIO for nexbox a95x which was forgotten in
  v1
- add the ethernet PHY reset GPIO for boards which were added since v1
  (wetek hub and wetek play2)
- rebased to apply against the current v4.11/dt64 branch
- new in v2 (patch #7): disabled ethernet support for the P200 board (see
  the commit description for more information). this patch is optional
- new in v2 (patch #9): removed the phy-mode property from meson-gx (see
  the commit description for more information). this patch is optional


[0] http://lists.infradead.org/pipermail/linux-amlogic/2017-January/002053.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2016-December/001834.html

Martin Blumenstingl (9):
  ARM64: dts: meson-gxbb-odroidc2: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-p201: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-nexbox-a95x: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-wetek-hub: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-wetek-play2: add the ethernet PHY's reset GPIO
  ARM64: dts: meson-gxbb-p20x: remove the ethernet node
  ARM64: dts: amlogic: add the ethernet TX delay configuration
  ARM64: dts: meson-gx: remove the phy-mode property from meson-gx

 arch/arm64/boot/dts/amlogic/meson-gx.dtsi          |  1 -
 .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts    | 17 ++++++++++++++
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts |  7 ++++++
 arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts    | 26 ++++++++++++++++++++++
 arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi   |  6 -----
 .../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi      | 20 +++++++++++++++++
 .../boot/dts/amlogic/meson-gxbb-wetek-hub.dts      | 26 ++++++++++++++++++++++
 .../boot/dts/amlogic/meson-gxbb-wetek-play2.dts    | 26 ++++++++++++++++++++++
 .../boot/dts/amlogic/meson-gxl-s905d-p230.dts      |  2 ++
 .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts |  2 ++
 arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts     |  2 ++
 11 files changed, 128 insertions(+), 7 deletions(-)

-- 
2.11.0