[PATCH 1/3] ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board
Teresa Remmet
t.remmet at phytec.de
Thu Jan 19 23:36:36 PST 2017
Hello Vladimir,
thank you for your review.
Am Donnerstag, den 19.01.2017, 16:24 +0200 schrieb Vladimir Zapolskiy:
> On 01/19/2017 03:07 PM, Teresa Remmet wrote:
> >
> > The phyCORE-AM335x development kit is a combination of the
> > phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> > of the PCM-953 are:
> > * ETH phy on carrier board: 1x RGMII
> > * 1x CAN
> > * Up to 4x UART
> > * USB0 (otg)
> > * USB1 (host)
> > * SD slot
> > * User gpio-keys
> > * User LEDs
> >
> > Signed-off-by: Teresa Remmet <t.remmet at phytec.de>
> > Reviewed-by: Wadim Egorov <w.egorov at phytec.de>
> > ---
> > .../devicetree/bindings/arm/omap/omap.txt | 3 +
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/am335x-pcm-953.dtsi | 303
> > +++++++++++++++++++++
> > arch/arm/boot/dts/am335x-phycore-rdk.dts | 27 ++
> > 4 files changed, 334 insertions(+)
> > create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
> > create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
> >
> > diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > index 05f95c3..8219b2c 100644
> > --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > @@ -151,6 +151,9 @@ Boards:
> > - AM335X SBC-T335 : single board computer, built around the Sitara
> > AM3352/4
> > compatible = "compulab,sbc-t335", "compulab,cm-t335",
> > "ti,am33xx"
> >
> > +- AM335X phyCORE-AM335x: Development kit
> > + compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-
> > som", "ti,am33xx"
> > +
> > - OMAP5 EVM : Evaluation Module
> > compatible = "ti,omap5-evm", "ti,omap5"
> >
> > diff --git a/arch/arm/boot/dts/Makefile
> > b/arch/arm/boot/dts/Makefile
> > index 7327250..dd71afe 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -573,6 +573,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
> > am335x-lxm.dtb \
> > am335x-nano.dtb \
> > am335x-pepper.dtb \
> > + am335x-phycore-rdk.dtb \
> > am335x-shc.dtb \
> > am335x-sbc-t335.dtb \
> > am335x-sl50.dtb \
> > diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > new file mode 100644
> > index 0000000..54a171d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > @@ -0,0 +1,303 @@
> > +/*
> > + * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
> > + * Author: Wadim Egorov <w.egorov at phytec.de>
> > + * Teresa Remmet <t.remmet at phytec.de>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > + model = "Phytec AM335x PCM-953";
> > + compatible = "phytec,am335x-pcm-953", "phytec,am335x-
> > phycore-som", "ti,am33xx";
> > +
> > + user_leds: user_leds {
> > + compatible = "gpio-leds";
> > + };
> > +
> > + user_buttons: user_buttons {
> > + compatible = "gpio-keys";
> > + };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> Please drop "simple-bus" compatible, see http://www.spinics.net/lists
> /linux-usb/msg101497.html
>
Ok, I will.
> >
> > +
> > + vcc3v3: fixedregulator at 1 {
> > + compatible = "regulator-fixed";
> > + };
> > +
> > + vcc1v8: fixedregulator at 2 {
> > + compatible = "regulator-fixed";
> > + };
> > + };
> > +};
> > +
> > +/* CAN */
> > +&am33xx_pinmux {
> Which .dtsi file contains the referenced am33xx_pinmux device node?
>
> You should include that file firstly, this is relevant to all other
> references to device nodes used in this file.
The device tree for the Phytec AM335x boards is spitted apart, as they
consist of an SoM and a carrier board. The am33xx_pinmux is defined in
the am33xx.dtsi which is included in the am335x-phycore-som.dtsi.
>
> >
> > + dcan1_pins: pinmux_dcan1 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP |
> > MUX_MODE2) /* uart1_rxd.dcan1_tx_mux2 */
> > + AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP |
> > MUX_MODE2) /* uart1_txd.dcan1_rx_mux2 */
> > + >;
> > + };
> > +};
> > +
> > +&dcan1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&dcan1_pins>;
> > + status = "okay";
> > +};
> > +
> > +/* Ethernet */
> > +&am33xx_pinmux {
> > + ethernet1_pins: pinmux_ethernet1 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a0.rgmii2_tctl */
> > + AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
> > + AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
> > + AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
> > + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
> > + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
> > + AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a6.rgmii2_tclk */
> > + AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
> > + AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
> > + AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
> > + AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
> > + AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN |
> > MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
> > + >;
> > + };
> > +};
> > +
> > +&cpsw_emac1 {
> > + phy-handle = <&phy1>;
> > + phy-mode = "rgmii-id";
> > + dual_emac_res_vlan = <2>;
> > + status = "okay";
> > +};
> > +
> > +&davinci_mdio {
> > + phy1: ethernet-phy at 1 {
> > + reg = <2>;
> There is a mismatch between unit address and 'reg' property values.
I will fix that.
>
> >
> > +
> > + /* Register 260 (104h) – RGMII Clock and Control
> > Pad Skew */
> > + rxc-skew-ps = <1400>;
> > + rxdv-skew-ps = <0>;
> > + txc-skew-ps = <1400>;
> > + txen-skew-ps = <0>;
> > + /* Register 261 (105h) – RGMII RX Data Pad Skew */
> > + rxd3-skew-ps = <0>;
> > + rxd2-skew-ps = <0>;
> > + rxd1-skew-ps = <0>;
> > + rxd0-skew-ps = <0>;
> > + /* Register 262 (106h) – RGMII TX Data Pad Skew */
> > + txd3-skew-ps = <0>;
> > + txd2-skew-ps = <0>;
> > + txd1-skew-ps = <0>;
> > + txd0-skew-ps = <0>;
> > + };
> > +};
> > +
> > +&mac {
> > + slaves = <2>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <ðernet0_pins ðernet1_pins>;
> > + dual_emac;
> It seems that TI has properties with underscores in the names, acked.
>
> >
> > +};
> > +
> > +/* Misc */
> > +&am33xx_pinmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cb_gpio_pins>;
> > +
> > + cb_gpio_pins: pinmux_cb_gpio {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7) /* uart0_ctsn.gpio1_8 */
> > + AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7) /* uart0_rtsn.gpio1_9 */
> > + >;
> > + };
> > +};
> > +
> > +/* MMC */
> > +&am33xx_pinmux {
> > + mmc1_pins: pinmux_mmc1_pins {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
> > + AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
> > + AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
> > + AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
> > + AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_clk.mmc0_clk */
> > + AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
> > + AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP |
> > MUX_MODE7) /* spi0_cs1.mmc0_sdcd */
> > + >;
> > + };
> > +};
> > +
> > +&mmc1 {
> > + vmmc-supply = <&vcc3v3>;
> > + bus-width = <4>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc1_pins>;
> > + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
> > + status = "okay";
> > +};
> > +
> > +/* Power */
> > +&vcc3v3 {
> > + regulator-name = "vcc3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > +};
> Please add properties directly into vcc3v3 device node.
I spitted the node apart as we structured the device tree in different
section. If I move this to the node directly the device tree
is not so readable in general any more. My opinion.
The same fits to the user leds and user buttons.
>
> >
> > +
> > +&vcc1v8 {
> > + regulator-name = "vcc1v8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > +};
> > +
> Please add properties directly into vcc1v8 device node.
>
> >
> > +/* UARTs */
> > +&am33xx_pinmux {
> > + uart0_pins: pinmux_uart0 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* uart0_rxd.uart0_rxd */
> > + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0) /* uart0_txd.uart0_txd */
> > + >;
> > + };
> > +
> > + uart1_pins: pinmux_uart1 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP |
> > MUX_MODE0) /* uart1_rxd.uart1_rxd */
> > + AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0) /* uart1_txd.uart1_txd */
> > + AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)
> > /* uart1_ctsn.uart1_ctsn */
> > + AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
> > + >;
> > + };
> > +
> > + uart2_pins: pinmux_uart2 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP |
> > MUX_MODE1) /* mii1_tx_clk.uart2_rxd */
> > + AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE1) /* mii1_rx_clk.uart2_txd */
> > + >;
> > + };
> > +
> > + uart3_pins: pinmux_uart3 {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP |
> > MUX_MODE1) /* mii1_rxd3.uart3_rxd */
> > + AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE1) /* mii1_rxd2.uart3_txd */
> > + >;
> > + };
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_pins>;
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pins>;
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart2_pins>;
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart3_pins>;
> > + status = "okay";
> > +};
> > +
> > +/* USB */
> > +&cppi41dma {
> > + status = "okay";
> > +};
> > +
> > +&usb_ctrl_mod {
> > + status = "okay";
> > +};
> > +
> > +&usb {
> > + status = "okay";
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > +};
> > +
> > +&usb0_phy {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + status = "okay";
> > + dr_mode = "host";
> > +};
> > +
> > +&usb1_phy {
> > + status = "okay";
> > +};
> > +
> > +/* User IO */
> > +&am33xx_pinmux {
> > + user_buttons_pins: pinmux_user_buttons {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN |
> > MUX_MODE7) /* emu0.gpio3_7 */
> > + AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN |
> > MUX_MODE7) /* emu1.gpio3_8 */
> > + >;
> > + };
> > +
> > + user_leds_pins: pinmux_user_leds {
> > + pinctrl-single,pins = <
> > + AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7) /* gpmc_csn1.gpio1_30 */
> > + AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7) /* gpmc_csn2.gpio1_31 */
> > + >;
> > + };
> > +};
> > +
> > +&user_buttons {
> Please add properties directly into user_buttons device node.
>
> >
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&user_buttons_pins>;
> > + status = "okay";
> Please remove the redundant property above.
I will remove it.
>
> >
> > +
> > + button at 0 {
> > + label = "home";
> > + linux,code = ;
> > + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> > + gpio-key,wakeup;
> > + };
> > +
> > + button at 1 {
> > + label = "menu";
> > + linux,code = ;
> > + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> > + gpio-key,wakeup;
> > + };
> > +};
> > +
> > +&user_leds {
> Please add properties directly into user_leds device node.
>
> >
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&user_leds_pins>;
> > + status = "okay";
> Please remove the redundant property above.
I will remove it.
Thank you,
Teresa
>
> >
> > +
> > + green {
> > + label = "green:user";
> > + gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "gpio";
> > + default-state = "on";
> > + };
> > +
> > + yellow {
> > + label = "yellow:user";
> > + gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> > + linux,default-trigger = "gpio";
> > + default-state = "on";
> > + };
> > +};
> > diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > new file mode 100644
> > index 0000000..305f0b3
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > @@ -0,0 +1,27 @@
> > +/*
> > + * Copyright (C) 2014 PHYTEC Messtechnik GmbH
> > + * Author: Wadim Egorov <w.egorov at phytec.de>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "am335x-phycore-som.dtsi"
> > +#include "am335x-pcm-953.dtsi"
> > +
> > +/* SoM */
> > +&i2c_eeprom {
> > + status = "okay";
> > +};
> > +
> > +&i2c_rtc {
> > + status = "okay";
> > +};
> > +
> > +&serial_flash {
> > + status = "okay";
> > +
> > +};
> >
More information about the linux-arm-kernel
mailing list