[PATCH v2 2/2] arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 08:34:04PM +0530, Pankaj Dubey wrote:
> From: Vivek Gautam <gautamvivek1987 at gmail.com>
> 
> Adding fixed voltage regulators for Vbus and Vbus-boost required
> by USB 3.0 DRD controller on Exynos7-espresso board.
> 
> Reviewed-by: Javier Martinez Canillas <javier at osg.samsung.com>
> Signed-off-by: Vivek Gautam <gautamvivek1987 at gmail.com>
> Signed-off-by: Pankaj Dubey <pankaj.dubey at samsung.com>

Same as patch 1.

> ---
>  arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 45 +++++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
> index 9cf73cf..8d5abdd 100644
> --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
> +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
> @@ -13,6 +13,7 @@
>  #include "exynos7.dtsi"
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/clock/samsung,s2mps11.h>
> +#include <dt-bindings/gpio/gpio.h>
>  
>  / {
>  	model = "Samsung Exynos7 Espresso board based on EXYNOS7";
> @@ -33,6 +34,29 @@
>  		device_type = "memory";
>  		reg = <0x0 0x40000000 0x0 0xC0000000>;
>  	};
> +
> +	usb30_vbus_reg: regulator-usb30 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VBUS_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gph1 1 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb30_vbus_en>;
> +		enable-active-high;
> +	};
> +
> +	usb3drd_boost_5v: regulator-usb3drd-boost {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VUSB_VBUS_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpf4 1 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb3drd_boost_en>;
> +		enable-active-high;
> +	};
> +
>  };
>  
>  &fin_pll {
> @@ -366,3 +390,24 @@
>  	vqmmc-supply = <&ldo2_reg>;
>  	disable-wp;
>  };
> +
> +&usbdrd_phy {
> +	vbus-supply = <&usb30_vbus_reg>;
> +	vbus-boost-supply = <&usb3drd_boost_5v>;
> +};
> +
> +&pinctrl_bus1 {
> +	usb30_vbus_en: usb30-vbus-en {
> +		samsung,pins = "gph1-1";
> +		samsung,pin-function = <1>;

Javier mentioned it, please use EXYNOS_PIN_FUNC_OUTPUT

> +		samsung,pin-pud = <0>;

EXYNOS_PIN_PULL_NONE

> +		samsung,pin-drv = <0>;

I think these are the same as in Exynos5422, so EXYNOS5420_PIN_DRV_LV1

Best regards,
Krzysztof


> +	};
> +
> +	usb3drd_boost_en: usb3drd-boost-en {
> +		samsung,pins = "gpf4-1";
> +		samsung,pin-function = <1>;
> +		samsung,pin-pud = <0>;
> +		samsung,pin-drv = <0>;
> +	};
> +};
> -- 
> 2.7.4
>