[PATCH v2 2/2] vring: Force use of DMA API for ARM-based systems

[Michael S. Tsirkin]

On Wed, Jan 11, 2017 at 10:12:36AM -0800, Andy Lutomirski wrote:
> On Wed, Jan 11, 2017 at 2:01 AM, Will Deacon <will.deacon at arm.com> wrote:
> > On Wed, Jan 11, 2017 at 01:33:31AM +0200, Michael S. Tsirkin wrote:
> >> On Tue, Jan 10, 2017 at 05:51:18PM +0000, Robin Murphy wrote:
> >> > From: Will Deacon <will.deacon at arm.com>
> >> >
> >> > Booting Linux on an ARM fastmodel containing an SMMU emulation results
> >> > in an unexpected I/O page fault from the legacy virtio-blk PCI device:
> >> >
> >> > [    1.211721] arm-smmu-v3 2b400000.smmu: event 0x10 received:
> >> > [    1.211800] arm-smmu-v3 2b400000.smmu:   0x00000000fffff010
> >> > [    1.211880] arm-smmu-v3 2b400000.smmu:   0x0000020800000000
> >> > [    1.211959] arm-smmu-v3 2b400000.smmu:   0x00000008fa081002
> >> > [    1.212075] arm-smmu-v3 2b400000.smmu:   0x0000000000000000
> >> > [    1.212155] arm-smmu-v3 2b400000.smmu: event 0x10 received:
> >> > [    1.212234] arm-smmu-v3 2b400000.smmu:   0x00000000fffff010
> >> > [    1.212314] arm-smmu-v3 2b400000.smmu:   0x0000020800000000
> >> > [    1.212394] arm-smmu-v3 2b400000.smmu:   0x00000008fa081000
> >> > [    1.212471] arm-smmu-v3 2b400000.smmu:   0x0000000000000000
> >> >
> >> > <system hangs failing to read partition table>
> >> >
> >> > This is because the virtio-blk is behind an SMMU, so we have consequently
> >> > swizzled its DMA ops and configured the SMMU to translate accesses. This
> >> > then requires the vring code to use the DMA API to establish translations,
> >> > otherwise all transactions will result in fatal faults and termination.
> >> >
> >> > Given that ARM-based systems only see an SMMU if one is really present
> >> > (the topology is all described by firmware tables such as device-tree or
> >> > IORT), then we can safely use the DMA API for all virtio devices.
> >> >
> >> > Cc: Andy Lutomirski <luto at kernel.org>
> >> > Cc: Michael S. Tsirkin <mst at redhat.com>
> >> > Signed-off-by: Will Deacon <will.deacon at arm.com>
> >>
> >> I'd like to better understand then need for this one.
> >> Can't the device in question just set VIRTIO_F_IOMMU_PLATFORM ?
> >>
> >> I'd rather we avoided need for more hacks and just
> >> have everyone switch to that.
> >
> > There are a couple of problems with VIRTIO_F_IOMMU_PLATFORM:
> >
> > 1. It doesn't exist for legacy devices, which are all we have on the
> >    platform in question.
> >
> > 2. It's not documented in the virtio sp^H^HSTOP PRESS. I see you applied
> >    my patch ;). Thanks.
> >
> > In which case, for non-legacy devices we should definitely be using
> > VIRTIO_F_IOMMU_PLATFORM, but since this platform hasn't yet moved to the
> > world of flying cars, could we unconditionally set the DMA ops on ARM
> > for legacy devices? The alternative is disabling the SMMU altogether,
> > but that's less than ideal because there are non-virtio devices on the
> > same PCI bus.
> 
> Also, on ARM, using the DMA API appears to *always* be the correct
> approach.  Why not do it all the time, then?  The non-DMA-API path is
> a legacy thing that is needed because a few platforms incorrectly
> enumerate their IOMMUs.  ARM gets it right, so I don't see why ARM
> should be subject to the legacy mess.

I didn't realize ARM gets this right. QEMU still pokes at
physical addresses directly in legacy mode so I wonder how could
that be the case. I'll try to find out.

> Even on x86, it should be possible to get the code into a state where
> using DMA ops is always correct.
> 
> --Andy

This I could totally get behind. A driver would install some per device
flag to make it figure out IOMMU does not apply, and in a portable way
since at least x86 and PPC need this, maybe more. This would/should
also handle the bug that admin can bind vfio to legacy virtio
devices even without the noiommu mode.

-- 
MST