[linux-sunxi][PATCH] ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
Code Kipper
codekipper at gmail.com
Thu Jan 12 09:39:06 PST 2017
On 12 January 2017 at 18:28, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi,
>
> On Thu, Jan 12, 2017 at 06:11:35PM +0100, codekipper at gmail.com wrote:
>> From: Marcus Cooper <codekipper at gmail.com>
>>
>> The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
>> 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
>> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, HDMI, an IR
>> receiver, 1 LEDs and an optical S/PDIF connector.
>>
>> Signed-off-by: Marcus Cooper <codekipper at gmail.com>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 187 ++++++++++++++++++++++++++++++
>> 2 files changed, 188 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 78a94b747059..75960b1468a4 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -857,6 +857,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-a83t-cubietruck-plus.dtb \
>> sun8i-h2-plus-orangepi-zero.dtb \
>> sun8i-h3-bananapi-m2-plus.dtb \
>> + sun8i-h3-beelink-x2.dtb \
>> sun8i-h3-nanopi-m1.dtb \
>> sun8i-h3-nanopi-neo.dtb \
>> sun8i-h3-orangepi-2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
>> new file mode 100644
>> index 000000000000..bc5aed52cb1d
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
>> @@ -0,0 +1,187 @@
>> +/*
>> + * Copyright (C) 2017 Marcus Cooper <codekipper at gmail.com>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/dts-v1/;
>> +#include "sun8i-h3.dtsi"
>> +#include "sunxi-common-regulators.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> + model = "Beelink X2";
>> + compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
>> + ethernet1 = &rtl8189ftv;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pwr_led_x2>;
>
> Please drop all the pinctrl nodes for the GPIOs. They're useless, and
> will be harmful when we'll switch to a stricter pinctrl driver.
>
ACK
>> +
>> + pwr_led {
>> + label = "beelink-x2:red:pwr";
>> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
>> + default-state = "on";
>> + };
>> + };
>> +
>> + gpio_keys {
>> + compatible = "gpio-keys";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&sw_r_x2>;
>> +
>> + sw4 {
>> + label = "power";
>> + linux,code = <BTN_0>;
>
> Should that be BTN_0 then if the label is that one?
>
ACK
>> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + wifi_pwrseq: wifi_pwrseq {
>> + compatible = "mmc-pwrseq-simple";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&wifi_en_x2>;
>> + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
>> + };
>> +};
>> +
>> +&ehci1 {
>> + status = "okay";
>> +};
>> +
>> +&ir {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ir_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
>> + cd-inverted;
>> + status = "okay";
>> +};
>> +
>> +&mmc1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc1_pins_a>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + non-removable;
>> + status = "okay";
>> +
>> + /*
>> + * Explicitly define the sdio device, so that we can add an ethernet
>> + * alias for it (which e.g. makes u-boot set a mac-address).
>> + */
>> + rtl8189ftv: sdio_wifi at 1 {
>> + reg = <1>;
>> + };
>> +};
>> +
>> +&mmc2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc2_8bit_pins>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <8>;
>> + non-removable;
>> + cap-mmc-hw-reset;
>> + status = "okay";
>> +};
>> +
>> +&mmc2_8bit_pins {
>> + /* Increase drive strength for DDR modes */
>> + drive-strength = <40>;
>
> Have you actually tested that it was needed?
>
I'll confess that I've rushed this one as I just wanted to verify my
spdif changes. I'll respin this,
BR,
CK
>> + /* eMMC is missing pull-ups */
>> + bias-pull-up;
>
> This is already enabled in the DTSI.
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
More information about the linux-arm-kernel
mailing list