[linux-sunxi][PATCH] ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
codekipper at gmail.com
codekipper at gmail.com
Thu Jan 12 09:11:35 PST 2017
From: Marcus Cooper <codekipper at gmail.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, HDMI, an IR
receiver, 1 LEDs and an optical S/PDIF connector.
Signed-off-by: Marcus Cooper <codekipper at gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 187 ++++++++++++++++++++++++++++++
2 files changed, 188 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 78a94b747059..75960b1468a4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -857,6 +857,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
+ sun8i-h3-beelink-x2.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-neo.dtb \
sun8i-h3-orangepi-2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
new file mode 100644
index 000000000000..bc5aed52cb1d
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -0,0 +1,187 @@
+/*
+ * Copyright (C) 2017 Marcus Cooper <codekipper at gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Beelink X2";
+ compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet1 = &rtl8189ftv;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_led_x2>;
+
+ pwr_led {
+ label = "beelink-x2:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_x2>;
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_en_x2>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ rtl8189ftv: sdio_wifi at 1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ drive-strength = <40>;
+ /* eMMC is missing pull-ups */
+ bias-pull-up;
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&r_pio {
+ pwr_led_x2: led_pins at 0 {
+ pins = "PL10";
+ function = "gpio_out";
+ };
+
+ sw_r_x2: key_pins at 0 {
+ pins = "PL3";
+ function = "gpio_in";
+ };
+
+ wifi_en_x2: wifi_en_pin {
+ pins = "PL7";
+ function = "gpio_out";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is on as long as VCC-IO is on */
+ status = "okay";
+};
--
2.11.0
More information about the linux-arm-kernel
mailing list