[PATCH] PCI: thunder-pem: Add support for cn81xx and cn83xx SoCs.

[David Daney]

On 01/11/2017 11:11 AM, David Daney wrote:
> From: David Daney <david.daney at cavium.com>
>
> The pci-thunder-pem driver was initially developed for cn88xx SoCs.
> The cn81xx and cn83xx members of the same family of SoCs has a
> slightly different configuration of interrupt resources in the PEM
> hardware, which prevents the INTA legacy interrupt source from
> functioning with the current driver.
>
> There are two fixes required:
>
> 1) Don't fixup the PME interrupt on the newer SoCs as it already has
> the proper value.
>
> 2) Report MSI-X Capability Table Size of 2 for the newer SoCs, so the
> core MSI-X code doesn't inadvertently clobber the INTA machinery that
> happens to reside immediately following the table.
>
> Signed-off-by: David Daney <david.daney at cavium.com>
> ---
>  drivers/pci/host/pci-thunder-pem.c | 25 ++++++++++++++++++++-----
>  1 file changed, 20 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/pci/host/pci-thunder-pem.c b/drivers/pci/host/pci-thunder-pem.c
> index af722eb..eea466f 100644
> --- a/drivers/pci/host/pci-thunder-pem.c
> +++ b/drivers/pci/host/pci-thunder-pem.c
> @@ -36,7 +36,7 @@ struct thunder_pem_pci {
>  static int thunder_pem_bridge_read(struct pci_bus *bus, unsigned int devfn,
>  				   int where, int size, u32 *val)
>  {
> -	u64 read_val;
> +	u64 read_val, tmp_val;
>  	struct pci_config_window *cfg = bus->sysdata;
>  	struct thunder_pem_pci *pem_pci = (struct thunder_pem_pci *)cfg->priv;
>
> @@ -65,13 +65,28 @@ static int thunder_pem_bridge_read(struct pci_bus *bus, unsigned int devfn,
>  		read_val |= 0x00007000; /* Skip MSI CAP */
>  		break;
>  	case 0x70: /* Express Cap */
> -		/* PME interrupt on vector 2*/
> -		read_val |= (2u << 25);
> +		/*
> +		 * Change PME interrupt to vector 2 on T88 where it
> +		 * reads as 0, else leave it alone.
> +		 */
> +		if (!(read_val & (0x1f << 25)))
> +			read_val |= (2u << 25);
>  		break;
>  	case 0xb0: /* MSI-X Cap */
> -		/* TableSize=4, Next Cap is EA */
> +		/* TableSize=2 or 4, Next Cap is EA */
>  		read_val &= 0xc00000ff;
> -		read_val |= 0x0003bc00;
> +		/*
> +		 * If Express Cap(0x70) raw PME vector reads as 2 we are on

Crap!  The comment is incorrect  s/2/0/, I guess I will send a corrected 
patch.  The code is correct though.


> +		 * T88 and TableSize is reported as 4, else TableSize
> +		 * is 2.
> +		 */
> +		writeq(0x70, pem_pci->pem_reg_base + PEM_CFG_RD);
> +		tmp_val = readq(pem_pci->pem_reg_base + PEM_CFG_RD);
> +		tmp_val >>= 32;
> +		if (!(tmp_val & (0x1f << 25)))
> +			read_val |= 0x0003bc00;
> +		else
> +			read_val |= 0x0001bc00;
>  		break;
>  	case 0xb4:
>  		/* Table offset=0, BIR=0 */
>