[PATCH 3/4] iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Wed Jan 11 09:43:33 PST 2017
This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.
The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets, as well as by reading (various versions of) the vendor
driver and by inspecting the registers on the vendor kernels of my
testing-hardware.
Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.
Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
accuracy of the results - in my tests the results were less than 3%
off without calibration compared to the vendor driver). Adding support
for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
Adding support for this is probably not so easy since (based on the
u-boot sources) most SoC versions are using different registers and
algorithms for the conversion from "ADC value" to temperature.
Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
individually because otherwise the ADC would be drawing power
constantly)
- interrupt support (similar to the vendor driver this new driver is
polling the results. It is unclear if the IRQ-mode is supported on
older (Meson6 or Meson8) hardware as well or if there are any errata)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
drivers/iio/adc/Kconfig | 12 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/meson_saradc.c | 860 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 873 insertions(+)
create mode 100644 drivers/iio/adc/meson_saradc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 9c8b558ba19e..86059b9b91bf 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -371,6 +371,18 @@ config MEN_Z188_ADC
This driver can also be built as a module. If so, the module will be
called men_z188_adc.
+config MESON_SARADC
+ tristate "Amlogic Meson SAR ADC driver"
+ default ARCH_MESON
+ depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST)
+ select REGMAP_MMIO
+ help
+ Say yes here to build support for the SAR ADC found in Amlogic Meson
+ SoCs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called meson_saradc.
+
config MXS_LRADC
tristate "Freescale i.MX23/i.MX28 LRADC"
depends on (ARCH_MXS || COMPILE_TEST) && HAS_IOMEM
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d36c4be8d1fc..de05b9e75f8f 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_MCP320X) += mcp320x.o
obj-$(CONFIG_MCP3422) += mcp3422.o
obj-$(CONFIG_MEDIATEK_MT6577_AUXADC) += mt6577_auxadc.o
obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
+obj-$(CONFIG_MESON_SARADC) += meson_saradc.o
obj-$(CONFIG_MXS_LRADC) += mxs-lradc.o
obj-$(CONFIG_NAU7802) += nau7802.o
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
diff --git a/drivers/iio/adc/meson_saradc.c b/drivers/iio/adc/meson_saradc.c
new file mode 100644
index 000000000000..06e8ac620385
--- /dev/null
+++ b/drivers/iio/adc/meson_saradc.c
@@ -0,0 +1,860 @@
+/*
+ * Amlogic Meson Successive Approximation Register (SAR) A/D Converter
+ *
+ * Copyright (C) 2017 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iio/iio.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#define SAR_ADC_REG0 0x00
+ #define SAR_ADC_REG0_PANEL_DETECT BIT(31)
+ #define SAR_ADC_REG0_BUSY_MASK GENMASK(30, 28)
+ #define SAR_ADC_REG0_DELTA_BUSY BIT(30)
+ #define SAR_ADC_REG0_AVG_BUSY BIT(29)
+ #define SAR_ADC_REG0_SAMPLE_BUSY BIT(28)
+ #define SAR_ADC_REG0_FIFO_FULL BIT(27)
+ #define SAR_ADC_REG0_FIFO_EMPTY BIT(26)
+ #define SAR_ADC_REG0_FIFO_COUNT_MASK GENMASK(25, 21)
+ #define SAR_ADC_REG0_ADC_BIAS_CTRL_MASK GENMASK(20, 19)
+ #define SAR_ADC_REG0_CURR_CHAN_ID_MASK GENMASK(18, 16)
+ #define SAR_ADC_REG0_ADC_TEMP_SEN_SEL BIT(15)
+ #define SAR_ADC_REG0_SAMPLING_STOP BIT(14)
+ #define SAR_ADC_REG0_CHAN_DELTA_EN_MASK GENMASK(13, 12)
+ #define SAR_ADC_REG0_DETECT_IRQ_POL BIT(10)
+ #define SAR_ADC_REG0_DETECT_IRQ_EN BIT(9)
+ #define SAR_ADC_REG0_FIFO_CNT_IRQ_MASK GENMASK(8, 4)
+ #define SAR_ADC_REG0_FIFO_IRQ_EN BIT(3)
+ #define SAR_ADC_REG0_SAMPLING_START BIT(2)
+ #define SAR_ADC_REG0_CONTINUOUS_EN BIT(1)
+ #define SAR_ADC_REG0_SAMPLE_ENGINE_ENABLE BIT(0)
+
+#define SAR_ADC_CHAN_LIST 0x04
+ #define SAR_ADC_CHAN_LIST_MAX_INDEX_MASK GENMASK(26, 24)
+ #define SAR_ADC_CHAN_CHAN_ENTRY_MASK(_chan) \
+ (GENMASK(2, 0) << (_chan * 3))
+
+#define SAR_ADC_AVG_CNTL 0x08
+ #define SAR_ADC_AVG_CNTL_AVG_MODE_SHIFT(_chan) \
+ (16 + (_chan * 2))
+ #define SAR_ADC_AVG_CNTL_AVG_MODE_MASK(_chan) \
+ (GENMASK(17, 16) << (_chan * 2))
+ #define SAR_ADC_AVG_CNTL_NUM_SAMPLES_SHIFT(_chan) \
+ (0 + (_chan * 2))
+ #define SAR_ADC_AVG_CNTL_NUM_SAMPLES_MASK(_chan) \
+ (GENMASK(1, 0) << (_chan * 2))
+
+#define SAR_ADC_REG3 0x0c
+ #define SAR_ADC_REG3_CNTL_USE_SC_DLY BIT(31)
+ #define SAR_ADC_REG3_CLK_EN BIT(30)
+ #define SAR_ADC_REG3_BL30_INITIALIZED BIT(28)
+ #define SAR_ADC_REG3_CTRL_CONT_RING_COUNTER_EN BIT(27)
+ #define SAR_ADC_REG3_CTRL_SAMPLING_CLOCK_PHASE BIT(26)
+ #define SAR_ADC_REG3_CTRL_CHAN7_MUX_SEL_MASK GENMASK(25, 23)
+ #define SAR_ADC_REG3_DETECT_EN BIT(22)
+ #define SAR_ADC_REG3_ADC_EN BIT(21)
+ #define SAR_ADC_REG3_PANEL_DETECT_COUNT_MASK GENMASK(20, 18)
+ #define SAR_ADC_REG3_PANEL_DETECT_FILTER_TB_MASK GENMASK(17, 16)
+ #define SAR_ADC_REG3_ADC_CLK_DIV_SHIFT 10
+ #define SAR_ADC_REG3_ADC_CLK_DIV_WIDTH 5
+ #define SAR_ADC_REG3_ADC_CLK_DIV_MASK GENMASK(15, 10)
+ #define SAR_ADC_REG3_BLOCK_DLY_SEL_MASK GENMASK(9, 8)
+ #define SAR_ADC_REG3_BLOCK_DLY_MASK GENMASK(7, 0)
+
+#define SAR_ADC_DELAY 0x10
+ #define SAR_ADC_DELAY_INPUT_DLY_SEL_MASK GENMASK(25, 24)
+ #define SAR_ADC_DELAY_BL30_BUSY BIT(15)
+ #define SAR_ADC_DELAY_KERNEL_BUSY BIT(14)
+ #define SAR_ADC_DELAY_INPUT_DLY_CNT_MASK GENMASK(23, 16)
+ #define SAR_ADC_DELAY_SAMPLE_DLY_SEL_MASK GENMASK(9, 8)
+ #define SAR_ADC_DELAY_SAMPLE_DLY_CNT_MASK GENMASK(7, 0)
+
+#define SAR_ADC_LAST_RD 0x14
+ #define SAR_ADC_LAST_RD_LAST_CHANNEL1_MASK GENMASK(23, 16)
+ #define SAR_ADC_LAST_RD_LAST_CHANNEL0_MASK GENMASK(9, 0)
+
+#define SAR_ADC_FIFO_RD 0x18
+ #define SAR_ADC_FIFO_RD_CHAN_ID_MASK GENMASK(14, 12)
+ #define SAR_ADC_FIFO_RD_SAMPLE_VALUE_MASK GENMASK(11, 0)
+
+#define SAR_ADC_AUX_SW 0x1c
+ #define SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK(_chan) \
+ (GENMASK(10, 8) << ((_chan - 2) * 2))
+ #define SAR_ADC_AUX_SW_VREF_P_MUX BIT(6)
+ #define SAR_ADC_AUX_SW_VREF_N_MUX BIT(5)
+ #define SAR_ADC_AUX_SW_MODE_SEL BIT(4)
+ #define SAR_ADC_AUX_SW_YP_DRIVE_SW BIT(3)
+ #define SAR_ADC_AUX_SW_XP_DRIVE_SW BIT(2)
+ #define SAR_ADC_AUX_SW_YM_DRIVE_SW BIT(1)
+ #define SAR_ADC_AUX_SW_XM_DRIVE_SW BIT(0)
+
+#define SAR_ADC_CHAN_10_SW 0x20
+ #define SAR_ADC_CHAN_10_SW_CHAN1_MUX_SEL_MASK GENMASK(25, 23)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_VREF_P_MUX BIT(22)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_VREF_N_MUX BIT(21)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_MODE_SEL BIT(20)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_YP_DRIVE_SW BIT(19)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_XP_DRIVE_SW BIT(18)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_YM_DRIVE_SW BIT(17)
+ #define SAR_ADC_CHAN_10_SW_CHAN1_XM_DRIVE_SW BIT(16)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_MUX_SEL_MASK GENMASK(9, 7)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_VREF_P_MUX BIT(6)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_VREF_N_MUX BIT(5)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_MODE_SEL BIT(4)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_YP_DRIVE_SW BIT(3)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_XP_DRIVE_SW BIT(2)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_YM_DRIVE_SW BIT(1)
+ #define SAR_ADC_CHAN_10_SW_CHAN0_XM_DRIVE_SW BIT(0)
+
+#define SAR_ADC_DETECT_IDLE_SW 0x24
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_SW_EN BIT(26)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_MUX_MASK GENMASK(25, 23)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_VREF_P_MUX BIT(22)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_VREF_N_MUX BIT(21)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_SEL BIT(20)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_YP_DRIVE_SW BIT(19)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_XP_DRIVE_SW BIT(18)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_YM_DRIVE_SW BIT(17)
+ #define SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_XM_DRIVE_SW BIT(16)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_MUX_SEL_MASK GENMASK(9, 7)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_VREF_P_MUX BIT(6)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_VREF_N_MUX BIT(5)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_SEL BIT(4)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_YP_DRIVE_SW BIT(3)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_XP_DRIVE_SW BIT(2)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_YM_DRIVE_SW BIT(1)
+ #define SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_XM_DRIVE_SW BIT(0)
+
+#define SAR_ADC_DELTA_10 0x28
+ #define SAR_ADC_DELTA_10_TEMP_SEL BIT(27)
+ #define SAR_ADC_DELTA_10_TS_REVE1 BIT(26)
+ #define SAR_ADC_DELTA_10_CHAN1_DELTA_VALUE_SHIFT 16
+ #define SAR_ADC_DELTA_10_CHAN1_DELTA_VALUE_MASK GENMASK(25, 16)
+ #define SAR_ADC_DELTA_10_TS_REVE0 BIT(15)
+ #define SAR_ADC_DELTA_10_TS_C_SHIFT 11
+ #define SAR_ADC_DELTA_10_TS_C_MASK GENMASK(14, 11)
+ #define SAR_ADC_DELTA_10_TS_VBG_EN BIT(10)
+ #define SAR_ADC_DELTA_10_CHAN0_DELTA_VALUE_SHIFT 0
+ #define SAR_ADC_DELTA_10_CHAN0_DELTA_VALUE_MASK GENMASK(9, 0)
+
+/* NOTE: registers from here are undocumented (the vendor Linux kernel driver
+ * and u-boot source served as reference). These only seem to be relevant on
+ * GXBB and newer.
+ */
+#define SAR_ADC_REG11 0x2c
+ #define SAR_ADC_REG11_BANDGAP_EN BIT(13)
+
+#define SAR_ADC_REG13 0x34
+ #define SAR_ADC_REG13_12BIT_CALIBRATION_MASK GENMASK(13, 8)
+
+#define SAR_ADC_MAX_FIFO_SIZE 32
+#define SAR_ADC_NUM_CHANNELS ARRAY_SIZE(meson_saradc_iio_channels)
+#define SAR_ADC_VALUE_MASK(_priv) (BIT(_priv->resolution) - 1)
+
+#define MESON_SAR_ADC_CHAN(_chan, _type) { \
+ .type = _type, \
+ .indexed = true, \
+ .channel = _chan, \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_AVERAGE_RAW), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
+ .datasheet_name = "SAR_ADC_CH"#_chan, \
+}
+
+/* TODO: the hardware supports IIO_TEMP for channel 6 as well which is
+ * currently not supported by this driver.
+ */
+static const struct iio_chan_spec meson_saradc_iio_channels[] = {
+ MESON_SAR_ADC_CHAN(0, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(1, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(2, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(3, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(4, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(5, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(6, IIO_VOLTAGE),
+ MESON_SAR_ADC_CHAN(7, IIO_VOLTAGE),
+ IIO_CHAN_SOFT_TIMESTAMP(8),
+};
+
+enum meson_saradc_avg_mode {
+ NO_AVERAGING = 0x0,
+ MEAN_AVERAGING = 0x1,
+ MEDIAN_AVERAGING = 0x2,
+};
+
+enum meson_saradc_num_samples {
+ ONE_SAMPLE = 0x0,
+ TWO_SAMPLES = 0x1,
+ FOUR_SAMPLES = 0x2,
+ EIGHT_SAMPLES = 0x3,
+};
+
+enum meson_saradc_chan7_mux_sel {
+ CHAN7_MUX_VSS = 0x0,
+ CHAN7_MUX_VDD_DIV4 = 0x1,
+ CHAN7_MUX_VDD_DIV2 = 0x2,
+ CHAN7_MUX_VDD_MUL3_DIV4 = 0x3,
+ CHAN7_MUX_VDD = 0x4,
+ CHAN7_MUX_CH7_INPUT = 0x7,
+};
+
+struct meson_saradc_priv {
+ struct regmap *regmap;
+ struct clk *clkin;
+ struct clk *core_clk;
+ struct clk *sana_clk;
+ struct clk *adc_sel_clk;
+ struct clk *adc_clk;
+ struct clk_gate clk_gate;
+ struct clk *adc_div_clk;
+ struct clk_divider clk_div;
+ struct regulator *vref;
+ struct completion completion;
+ u8 resolution;
+};
+
+static const struct regmap_config meson_saradc_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = SAR_ADC_REG13,
+};
+
+static unsigned int meson_saradc_get_fifo_count(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ u32 regval;
+
+ regmap_read(priv->regmap, SAR_ADC_REG0, ®val);
+
+ return FIELD_GET(SAR_ADC_REG0_FIFO_COUNT_MASK, regval);
+}
+
+static int meson_saradc_wait_busy_clear(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int regval, timeout = 10000;
+
+ do {
+ udelay(1);
+ regmap_read(priv->regmap, SAR_ADC_REG0, ®val);
+ } while (FIELD_GET(SAR_ADC_REG0_BUSY_MASK, regval) && timeout--);
+
+ if (timeout < 0)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+static int meson_saradc_read_raw_sample(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ int *val)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int ret, regval, fifo_chan, fifo_val, sum = 0, count = 0;
+
+ ret = meson_saradc_wait_busy_clear(indio_dev);
+ if (ret)
+ return ret;
+
+ regmap_read(priv->regmap, SAR_ADC_REG0, ®val);
+
+ while (meson_saradc_get_fifo_count(indio_dev) > 0 &&
+ count < SAR_ADC_MAX_FIFO_SIZE) {
+ regmap_read(priv->regmap, SAR_ADC_FIFO_RD, ®val);
+
+ fifo_chan = FIELD_GET(SAR_ADC_FIFO_RD_CHAN_ID_MASK, regval);
+ if (fifo_chan == chan->channel) {
+ fifo_val = FIELD_GET(SAR_ADC_FIFO_RD_SAMPLE_VALUE_MASK,
+ regval) & SAR_ADC_VALUE_MASK(priv);
+ sum += fifo_val;
+ count++;
+ }
+ }
+
+ if (!count)
+ return -ENOENT;
+
+ *val = sum / count;
+
+ return 0;
+}
+
+static void meson_saradc_set_averaging(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum meson_saradc_avg_mode mode,
+ enum meson_saradc_num_samples samples)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ u32 val;
+
+ val = samples << SAR_ADC_AVG_CNTL_NUM_SAMPLES_SHIFT(chan->channel);
+ regmap_update_bits(priv->regmap, SAR_ADC_AVG_CNTL,
+ SAR_ADC_AVG_CNTL_NUM_SAMPLES_MASK(chan->channel),
+ val);
+
+ val = mode << SAR_ADC_AVG_CNTL_AVG_MODE_SHIFT(chan->channel);
+ regmap_update_bits(priv->regmap, SAR_ADC_AVG_CNTL,
+ SAR_ADC_AVG_CNTL_AVG_MODE_MASK(chan->channel), val);
+}
+
+static void meson_saradc_enable_channel(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ u32 regval;
+
+ /* the SAR ADC engine allows sampling multiple channels at the same
+ * time. to keep it simple we're only working with one *internal*
+ * channel, which starts counting at index 0 (which means: count = 1).
+ */
+ regval = FIELD_PREP(SAR_ADC_CHAN_LIST_MAX_INDEX_MASK, 0);
+ regmap_update_bits(priv->regmap, SAR_ADC_CHAN_LIST,
+ SAR_ADC_CHAN_LIST_MAX_INDEX_MASK, regval);
+
+ /* map channel index 0 to the channel which we want to read */
+ regval = FIELD_PREP(SAR_ADC_CHAN_CHAN_ENTRY_MASK(0), chan->channel);
+ regmap_update_bits(priv->regmap, SAR_ADC_CHAN_LIST,
+ SAR_ADC_CHAN_CHAN_ENTRY_MASK(0), regval);
+
+ regval = FIELD_PREP(SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_MUX_MASK,
+ chan->channel);
+ regmap_update_bits(priv->regmap, SAR_ADC_DETECT_IDLE_SW,
+ SAR_ADC_DETECT_IDLE_SW_DETECT_MODE_MUX_MASK,
+ regval);
+
+ regval = FIELD_PREP(SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_MUX_SEL_MASK,
+ chan->channel);
+ regmap_update_bits(priv->regmap, SAR_ADC_DETECT_IDLE_SW,
+ SAR_ADC_DETECT_IDLE_SW_IDLE_MODE_MUX_SEL_MASK,
+ regval);
+
+ if (chan->channel == 6)
+ regmap_update_bits(priv->regmap, SAR_ADC_DELTA_10,
+ SAR_ADC_DELTA_10_TEMP_SEL, 0);
+}
+
+static void meson_saradc_set_channel7_mux(struct iio_dev *indio_dev,
+ enum meson_saradc_chan7_mux_sel sel)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ u32 regval;
+
+ regval = FIELD_PREP(SAR_ADC_REG3_CTRL_CHAN7_MUX_SEL_MASK, sel);
+ regmap_update_bits(priv->regmap, SAR_ADC_REG3,
+ SAR_ADC_REG3_CTRL_CHAN7_MUX_SEL_MASK, regval);
+
+ usleep_range(10, 20);
+}
+
+static void meson_saradc_start_sample_engine(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG0,
+ SAR_ADC_REG0_SAMPLE_ENGINE_ENABLE,
+ SAR_ADC_REG0_SAMPLE_ENGINE_ENABLE);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG0,
+ SAR_ADC_REG0_SAMPLING_START,
+ SAR_ADC_REG0_SAMPLING_START);
+}
+
+static void meson_saradc_stop_sample_engine(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG0,
+ SAR_ADC_REG0_SAMPLING_STOP,
+ SAR_ADC_REG0_SAMPLING_STOP);
+
+ /* wait until all modules are stopped */
+ meson_saradc_wait_busy_clear(indio_dev);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG0,
+ SAR_ADC_REG0_SAMPLE_ENGINE_ENABLE, 0);
+}
+
+static void meson_saradc_lock(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int val;
+
+ mutex_lock(&indio_dev->mlock);
+
+ /* prevent BL30 from using the SAR ADC while we are using it */
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_KERNEL_BUSY,
+ SAR_ADC_DELAY_KERNEL_BUSY);
+
+ /* wait until BL30 releases it's lock (so we can use the SAR ADC) */
+ do {
+ udelay(1);
+ regmap_read(priv->regmap, SAR_ADC_DELAY, &val);
+ } while (val & SAR_ADC_DELAY_BL30_BUSY);
+}
+
+static void meson_saradc_unlock(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+
+ /* allow BL30 to use the SAR ADC again */
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_KERNEL_BUSY, 0);
+
+ mutex_unlock(&indio_dev->mlock);
+}
+
+static int meson_saradc_get_sample(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum meson_saradc_avg_mode avg_mode,
+ enum meson_saradc_num_samples avg_samples,
+ int *val)
+{
+ int ret, tmp;
+
+ meson_saradc_lock(indio_dev);
+
+ /* clear old values from the FIFO buffer, ignoring errors */
+ meson_saradc_read_raw_sample(indio_dev, chan, &tmp);
+
+ meson_saradc_set_averaging(indio_dev, chan, avg_mode, avg_samples);
+
+ meson_saradc_enable_channel(indio_dev, chan);
+
+ meson_saradc_start_sample_engine(indio_dev);
+ ret = meson_saradc_read_raw_sample(indio_dev, chan, val);
+ meson_saradc_stop_sample_engine(indio_dev);
+
+ meson_saradc_unlock(indio_dev);
+
+ if (ret) {
+ dev_warn(&indio_dev->dev,
+ "failed to read sample for channel %d: %d\n",
+ chan->channel, ret);
+ return ret;
+ }
+
+ return IIO_VAL_INT;
+}
+
+static int meson_saradc_iio_info_read_raw(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ int *val, int *val2, long mask)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ return meson_saradc_get_sample(indio_dev, chan, NO_AVERAGING,
+ ONE_SAMPLE, val);
+ break;
+
+ case IIO_CHAN_INFO_AVERAGE_RAW:
+ return meson_saradc_get_sample(indio_dev, chan, MEAN_AVERAGING,
+ EIGHT_SAMPLES, val);
+ break;
+
+ case IIO_CHAN_INFO_SCALE:
+ ret = regulator_get_voltage(priv->vref);
+ if (ret < 0) {
+ dev_err(&indio_dev->dev,
+ "failed to get vref voltage: %d\n", ret);
+ return ret;
+ }
+
+ *val = ret / 1000;
+ *val2 = priv->resolution;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static int meson_saradc_clk_init(struct iio_dev *indio_dev, void __iomem *base)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ struct clk_init_data init;
+ char clk_name[32];
+ const char *clk_parents[1];
+
+ snprintf(clk_name, sizeof(clk_name), "%s#adc_div",
+ of_node_full_name(indio_dev->dev.of_node));
+ init.name = devm_kstrdup(&indio_dev->dev, clk_name, GFP_KERNEL);
+ init.flags = 0;
+ init.ops = &clk_divider_ops;
+ clk_parents[0] = __clk_get_name(priv->clkin);
+ init.parent_names = clk_parents;
+ init.num_parents = 1;
+
+ priv->clk_div.reg = base + SAR_ADC_REG3;
+ priv->clk_div.shift = SAR_ADC_REG3_ADC_CLK_DIV_SHIFT;
+ priv->clk_div.width = SAR_ADC_REG3_ADC_CLK_DIV_WIDTH;
+ priv->clk_div.hw.init = &init;
+ priv->clk_div.flags = 0;
+
+ priv->adc_div_clk = devm_clk_register(&indio_dev->dev,
+ &priv->clk_div.hw);
+ if (WARN_ON(IS_ERR(priv->adc_div_clk)))
+ return PTR_ERR(priv->adc_div_clk);
+
+ snprintf(clk_name, sizeof(clk_name), "%s#adc_en",
+ of_node_full_name(indio_dev->dev.of_node));
+ init.name = devm_kstrdup(&indio_dev->dev, clk_name, GFP_KERNEL);
+ init.flags = CLK_SET_RATE_PARENT;
+ init.ops = &clk_gate_ops;
+ clk_parents[0] = __clk_get_name(priv->adc_div_clk);
+ init.parent_names = clk_parents;
+ init.num_parents = 1;
+
+ priv->clk_gate.reg = base + SAR_ADC_REG3;
+ priv->clk_gate.bit_idx = fls(SAR_ADC_REG3_CLK_EN);
+ priv->clk_gate.hw.init = &init;
+
+ priv->adc_clk = devm_clk_register(&indio_dev->dev, &priv->clk_gate.hw);
+ if (WARN_ON(IS_ERR(priv->adc_clk)))
+ return PTR_ERR(priv->adc_clk);
+
+ return 0;
+}
+
+static int meson_saradc_init(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int regval, ret;
+
+ /* make sure we start at CH7 input */
+ meson_saradc_set_channel7_mux(indio_dev, CHAN7_MUX_CH7_INPUT);
+
+ regmap_read(priv->regmap, SAR_ADC_REG3, ®val);
+ if (regval & SAR_ADC_REG3_BL30_INITIALIZED) {
+ dev_info(&indio_dev->dev, "already initialized by BL30\n");
+ return 0;
+ }
+
+ dev_info(&indio_dev->dev, "initializing SAR ADC\n");
+
+ meson_saradc_stop_sample_engine(indio_dev);
+
+ /* update the channel 6 MUX to select the temperature sensor */
+ regmap_update_bits(priv->regmap, SAR_ADC_REG0,
+ SAR_ADC_REG0_ADC_TEMP_SEN_SEL,
+ SAR_ADC_REG0_ADC_TEMP_SEN_SEL);
+
+ /* disable all channels by default */
+ regmap_write(priv->regmap, SAR_ADC_CHAN_LIST, 0x0);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG3,
+ SAR_ADC_REG3_CTRL_SAMPLING_CLOCK_PHASE, 0);
+ regmap_update_bits(priv->regmap, SAR_ADC_REG3,
+ SAR_ADC_REG3_CNTL_USE_SC_DLY,
+ SAR_ADC_REG3_CNTL_USE_SC_DLY);
+
+ /* delay between two samples = (10+1) * 1uS */
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_INPUT_DLY_CNT_MASK,
+ FIELD_PREP(SAR_ADC_DELAY_SAMPLE_DLY_CNT_MASK, 10));
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_SAMPLE_DLY_SEL_MASK,
+ FIELD_PREP(SAR_ADC_DELAY_SAMPLE_DLY_SEL_MASK, 0));
+
+ /* delay between two samples = (10+1) * 1uS */
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_INPUT_DLY_CNT_MASK,
+ FIELD_PREP(SAR_ADC_DELAY_INPUT_DLY_CNT_MASK, 10));
+ regmap_update_bits(priv->regmap, SAR_ADC_DELAY,
+ SAR_ADC_DELAY_INPUT_DLY_SEL_MASK,
+ FIELD_PREP(SAR_ADC_DELAY_INPUT_DLY_SEL_MASK, 1));
+
+ ret = clk_set_parent(priv->adc_sel_clk, priv->clkin);
+ if (ret) {
+ dev_err(&indio_dev->dev,
+ "failed to set adc parent to clkin\n");
+ return ret;
+ }
+
+ ret = clk_set_rate(priv->adc_clk, 1200000);
+ if (ret) {
+ dev_err(&indio_dev->dev, "failed to set adc clock rate\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int meson_saradc_hw_enable(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ meson_saradc_lock(indio_dev);
+
+ ret = regulator_enable(priv->vref);
+ if (ret < 0) {
+ dev_err(&indio_dev->dev, "failed to enable vref regulator\n");
+ goto err_vref;
+ }
+
+ ret = clk_prepare_enable(priv->core_clk);
+ if (ret) {
+ dev_err(&indio_dev->dev, "failed to enable core clk\n");
+ goto err_core_clk;
+ }
+
+ ret = clk_prepare_enable(priv->sana_clk);
+ if (ret) {
+ dev_err(&indio_dev->dev, "failed to enable sana clk\n");
+ goto err_sana_clk;
+ }
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG11,
+ SAR_ADC_REG11_BANDGAP_EN, SAR_ADC_REG11_BANDGAP_EN);
+ regmap_update_bits(priv->regmap, SAR_ADC_REG3, SAR_ADC_REG3_ADC_EN,
+ SAR_ADC_REG3_ADC_EN);
+
+ udelay(5);
+
+ ret = clk_prepare_enable(priv->adc_clk);
+ if (ret) {
+ dev_err(&indio_dev->dev, "failed to enable adc_en clk\n");
+ goto err_adc_clk;
+ }
+
+ meson_saradc_unlock(indio_dev);
+
+ return 0;
+
+err_adc_clk:
+ clk_disable_unprepare(priv->sana_clk);
+err_sana_clk:
+ clk_disable_unprepare(priv->core_clk);
+err_core_clk:
+ regulator_disable(priv->vref);
+err_vref:
+ meson_saradc_unlock(indio_dev);
+ return ret;
+}
+
+static void meson_saradc_hw_disable(struct iio_dev *indio_dev)
+{
+ struct meson_saradc_priv *priv = iio_priv(indio_dev);
+
+ meson_saradc_lock(indio_dev);
+
+ clk_disable_unprepare(priv->adc_clk);
+
+ regmap_update_bits(priv->regmap, SAR_ADC_REG3, SAR_ADC_REG3_ADC_EN, 0);
+ regmap_update_bits(priv->regmap, SAR_ADC_REG11,
+ SAR_ADC_REG11_BANDGAP_EN, 0);
+
+ clk_disable_unprepare(priv->sana_clk);
+ clk_disable_unprepare(priv->core_clk);
+
+ regulator_disable(priv->vref);
+
+ meson_saradc_unlock(indio_dev);
+}
+
+static const struct iio_info meson_saradc_iio_info = {
+ .read_raw = meson_saradc_iio_info_read_raw,
+ .driver_module = THIS_MODULE,
+};
+
+static const struct of_device_id meson_saradc_of_match[] = {
+ {
+ .compatible = "amlogic,meson-gxbb-saradc",
+ .data = (void *)10,
+ }, {
+ .compatible = "amlogic,meson-gxl-saradc",
+ .data = (void *)12,
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, meson_saradc_of_match);
+
+static int meson_saradc_probe(struct platform_device *pdev)
+{
+ struct meson_saradc_priv *priv;
+ struct iio_dev *indio_dev;
+ struct resource *res;
+ void __iomem *base;
+ const struct of_device_id *match;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
+ if (!indio_dev) {
+ dev_err(&pdev->dev, "failed allocating iio device\n");
+ return -ENOMEM;
+ }
+
+ priv = iio_priv(indio_dev);
+
+ match = of_match_device(meson_saradc_of_match, &pdev->dev);
+ priv->resolution = (unsigned long)match->data;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ priv->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+ &meson_saradc_regmap_config);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ init_completion(&priv->completion);
+
+ priv->clkin = devm_clk_get(&pdev->dev, "clkin");
+ if (IS_ERR(priv->clkin)) {
+ dev_err(&pdev->dev, "failed to get clkin\n");
+ return PTR_ERR(priv->clkin);
+ }
+
+ priv->core_clk = devm_clk_get(&pdev->dev, "core");
+ if (IS_ERR(priv->core_clk)) {
+ dev_err(&pdev->dev, "failed to get core clk\n");
+ return PTR_ERR(priv->core_clk);
+ }
+
+ priv->sana_clk = devm_clk_get(&pdev->dev, "sana");
+ if (IS_ERR(priv->sana_clk)) {
+ if (PTR_ERR(priv->sana_clk) == -ENOENT) {
+ priv->sana_clk = NULL;
+ } else {
+ dev_err(&pdev->dev, "failed to get sana clk\n");
+ return PTR_ERR(priv->sana_clk);
+ }
+ }
+
+ priv->adc_clk = devm_clk_get(&pdev->dev, "adc_clk");
+ if (IS_ERR(priv->adc_clk)) {
+ if (PTR_ERR(priv->adc_clk) == -ENOENT) {
+ priv->adc_clk = NULL;
+ } else {
+ dev_err(&pdev->dev, "failed to get adc clk\n");
+ return PTR_ERR(priv->adc_clk);
+ }
+ }
+
+ priv->adc_sel_clk = devm_clk_get(&pdev->dev, "adc_sel");
+ if (IS_ERR(priv->adc_sel_clk)) {
+ if (PTR_ERR(priv->adc_sel_clk) == -ENOENT) {
+ priv->adc_sel_clk = NULL;
+ } else {
+ dev_err(&pdev->dev, "failed to get adc_sel clk\n");
+ return PTR_ERR(priv->adc_sel_clk);
+ }
+ }
+
+ /* on pre-GXBB SoCs the SAR ADC itself provides the ADC clock: */
+ if (!priv->adc_clk) {
+ ret = meson_saradc_clk_init(indio_dev, base);
+ if (ret)
+ return ret;
+ }
+
+ priv->vref = devm_regulator_get(&pdev->dev, "vref");
+ if (IS_ERR(priv->vref)) {
+ dev_err(&pdev->dev, "failed to get vref regulator\n");
+ return PTR_ERR(priv->vref);
+ }
+
+ ret = meson_saradc_init(indio_dev);
+ if (ret)
+ goto err;
+
+ ret = meson_saradc_hw_enable(indio_dev);
+ if (ret)
+ goto err;
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ indio_dev->name = dev_name(&pdev->dev);
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->dev.of_node = pdev->dev.of_node;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &meson_saradc_iio_info;
+
+ indio_dev->channels = meson_saradc_iio_channels;
+ indio_dev->num_channels = SAR_ADC_NUM_CHANNELS;
+
+ ret = iio_device_register(indio_dev);
+ if (ret)
+ goto err_hw;
+
+ return 0;
+
+err_hw:
+ meson_saradc_hw_disable(indio_dev);
+err:
+ return ret;
+}
+
+static int meson_saradc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+ meson_saradc_hw_disable(indio_dev);
+ iio_device_unregister(indio_dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int meson_saradc_suspend(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+
+ meson_saradc_hw_disable(indio_dev);
+
+ return 0;
+}
+
+static int meson_saradc_resume(struct device *dev)
+{
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+
+ return meson_saradc_hw_enable(indio_dev);
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static SIMPLE_DEV_PM_OPS(meson_saradc_pm_ops,
+ meson_saradc_suspend, meson_saradc_resume);
+
+static struct platform_driver meson_saradc_driver = {
+ .probe = meson_saradc_probe,
+ .remove = meson_saradc_remove,
+ .driver = {
+ .name = "meson-saradc",
+ .of_match_table = meson_saradc_of_match,
+ .pm = &meson_saradc_pm_ops,
+ },
+};
+
+module_platform_driver(meson_saradc_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl at googlemail.com>");
+MODULE_DESCRIPTION("Amlogic Meson SAR ADC driver");
+MODULE_LICENSE("GPL v2");
--
2.11.0
More information about the linux-arm-kernel
mailing list