[PATCH v11 11/12] drm/mediatek: update DSI sub driver flow for sending commands to panel

YT Shen yt.shen at mediatek.com
Tue Jan 10 22:51:12 PST 2017


This patch update enable/disable flow of DSI module.
Original flow works on there is a bridge chip: DSI -> bridge -> panel.
In this case: DSI -> panel, the DSI sub driver flow should be updated.
We need to initialize DSI first so that we can send commands to panel.

Signed-off-by: shaoming chen <shaoming.chen at mediatek.com>
Signed-off-by: YT Shen <yt.shen at mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 89 +++++++++++++++++++++++++++++++-------
 1 file changed, 74 insertions(+), 15 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 85f22d2..21392c4 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -126,6 +126,10 @@
 #define CLK_HS_POST			(0xff << 8)
 #define CLK_HS_EXIT			(0xff << 16)
 
+#define DSI_VM_CMD_CON		0x130
+#define VM_CMD_EN			BIT(0)
+#define TS_VFP_EN			BIT(5)
+
 #define DSI_CMDQ0		0x180
 #define CONFIG				(0xff << 0)
 #define SHORT_PACKET			0
@@ -365,16 +369,23 @@ static void mtk_dsi_set_mode(struct mtk_dsi *dsi)
 	u32 vid_mode = CMD_MODE;
 
 	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
-		vid_mode = SYNC_PULSE_MODE;
-
-		if ((dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) &&
-		    !(dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE))
+		if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
 			vid_mode = BURST_MODE;
+		else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+			vid_mode = SYNC_PULSE_MODE;
+		else
+			vid_mode = SYNC_EVENT_MODE;
 	}
 
 	writel(vid_mode, dsi->regs + DSI_MODE_CTRL);
 }
 
+static void mtk_dsi_set_vm_cmd(struct mtk_dsi *dsi)
+{
+	mtk_dsi_mask(dsi, DSI_VM_CMD_CON, VM_CMD_EN, VM_CMD_EN);
+	mtk_dsi_mask(dsi, DSI_VM_CMD_CON, TS_VFP_EN, TS_VFP_EN);
+}
+
 static void mtk_dsi_ps_control_vact(struct mtk_dsi *dsi)
 {
 	struct videomode *vm = &dsi->vm;
@@ -512,6 +523,16 @@ static void mtk_dsi_start(struct mtk_dsi *dsi)
 	writel(1, dsi->regs + DSI_START);
 }
 
+static void mtk_dsi_stop(struct mtk_dsi *dsi)
+{
+	writel(0, dsi->regs + DSI_START);
+}
+
+static void mtk_dsi_set_cmd_mode(struct mtk_dsi *dsi)
+{
+	writel(CMD_MODE, dsi->regs + DSI_MODE_CTRL);
+}
+
 static void mtk_dsi_set_interrupt_enable(struct mtk_dsi *dsi)
 {
 	u32 inten = LPRX_RD_RDY_INT_FLAG | CMD_DONE_INT_FLAG | VM_DONE_INT_FLAG;
@@ -570,6 +591,19 @@ static irqreturn_t mtk_dsi_irq(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static s32 mtk_dsi_switch_to_cmd_mode(struct mtk_dsi *dsi, u8 irq_flag, u32 t)
+{
+	mtk_dsi_irq_data_clear(dsi, irq_flag);
+	mtk_dsi_set_cmd_mode(dsi);
+
+	if (!mtk_dsi_wait_for_irq_done(dsi, irq_flag, t)) {
+		DRM_ERROR("failed to switch cmd mode\n");
+		return -ETIME;
+	} else {
+		return 0;
+	}
+}
+
 static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 {
 	if (WARN_ON(dsi->refcount == 0))
@@ -578,6 +612,17 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	if (--dsi->refcount != 0)
 		return;
 
+	mtk_dsi_stop(dsi);
+	if (!mtk_dsi_switch_to_cmd_mode(dsi, VM_DONE_INT_FLAG, 500)) {
+		if (dsi->panel) {
+			if (drm_panel_unprepare(dsi->panel)) {
+				DRM_ERROR("failed to unprepare the panel\n");
+				return;
+			}
+		}
+	}
+
+	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_lane0_ulp_mode_enter(dsi);
 	mtk_dsi_clk_ulp_mode_enter(dsi);
 
@@ -596,13 +641,6 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 	if (dsi->enabled)
 		return;
 
-	if (dsi->panel) {
-		if (drm_panel_prepare(dsi->panel)) {
-			DRM_ERROR("failed to setup the panel\n");
-			return;
-		}
-	}
-
 	ret = mtk_dsi_poweron(dsi);
 	if (ret < 0) {
 		DRM_ERROR("failed to power on dsi\n");
@@ -610,22 +648,43 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 	}
 
 	mtk_dsi_rxtx_control(dsi);
+	mtk_dsi_ps_control_vact(dsi);
+	mtk_dsi_set_vm_cmd(dsi);
+	mtk_dsi_config_vdo_timing(dsi);
+	mtk_dsi_set_interrupt_enable(dsi);
 
 	mtk_dsi_clk_ulp_mode_leave(dsi);
 	mtk_dsi_lane0_ulp_mode_leave(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 0);
-	mtk_dsi_set_mode(dsi);
 
-	mtk_dsi_ps_control_vact(dsi);
-	mtk_dsi_config_vdo_timing(dsi);
-	mtk_dsi_set_interrupt_enable(dsi);
+	if (dsi->panel) {
+		if (drm_panel_prepare(dsi->panel)) {
+			DRM_ERROR("failed to prepare the panel\n");
+			goto err_dsi_power_off;
+		}
+	}
 
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
 	mtk_dsi_start(dsi);
 
+	if (dsi->panel) {
+		if (drm_panel_enable(dsi->panel)) {
+			DRM_ERROR("failed to enable the panel\n");
+			goto err_panel_disable;
+		}
+	}
+
 	dsi->enabled = true;
+
+	return;
+err_panel_disable:
+	mtk_dsi_stop(dsi);
+	if (dsi->panel)
+		drm_panel_unprepare(dsi->panel);
+err_dsi_power_off:
+	mtk_dsi_poweroff(dsi);
 }
 
 static void mtk_output_dsi_disable(struct mtk_dsi *dsi)
-- 
1.9.1




More information about the linux-arm-kernel mailing list