[PATCH] DTS: MCCMON6: IMX: Provide support for iMX6Q based Liebherr mccmon6 board
Lukasz Majewski
l.majewski at majess.pl
Mon Jan 2 06:44:37 PST 2017
Hi Vladimir,
Thank you for review. Comments without my remarks have been applied
already.
> Hello Lukasz,
>
> On 12/27/2016 01:19 AM, Lukasz Majewski wrote:
> > Signed-off-by: Lukasz Majewski <l.majewski at majess.pl>
>
> please add a commit message with a short description of the change.
>
> Also change subject line to "ARM: dts: imx6q: Add mccmon6 board
> support".
>
> > ---
> > MCCMON6 board support depends on following patches:
> >
> > 1. "video: backlight: pwm_bl: Initialize fb_bl_on[x] and use_count
> > during pwm_backlight_probe()"
> > http://patchwork.ozlabs.org/patch/708844/
> >
> > 2. "pwm: imx: Provide atomic operation for IMX PWM driver"
> > http://patchwork.ozlabs.org/patch/708847/ -
> > http://patchwork.ozlabs.org/patch/708843/
> >
> >
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6q-mccmon6.dts | 469
> > ++++++++++++++++++++++++++++++++++++ 2 files changed, 470
> > insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-mccmon6.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index c558ba7..7ce1080 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -382,6 +382,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6q-h100.dtb \
> > imx6q-hummingboard.dtb \
> > imx6q-icore-rqs.dtb \
> > + imx6q-mccmon6.dtb \
> > imx6q-marsboard.dtb \
>
> Please add a new line preserving alphabetical order.
>
> > imx6q-nitrogen6x.dtb \
> > imx6q-nitrogen6_max.dtb \
> > diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts
> > b/arch/arm/boot/dts/imx6q-mccmon6.dts new file mode 100644
> > index 0000000..7445d01
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
> > @@ -0,0 +1,469 @@
> > +/*
> > + * Copyright 2016
>
> Copyright holder is missing.
>
> > + *
> > + * Author: Lukasz Majewski <l.majewski at majess.pl>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + *
> > + */
>
> Please add an empty line here to improve readability.
>
> > +/dts-v1/;
>
> Please add an empty line here to improve readability.
>
> > +#include "imx6q.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/pwm/pwm.h>
> > +
> > +/ {
> > + model = "Monitor6 i.MX6 Quad Board";
>
> Missing hardware vendor name.
>
> > + compatible = "mccmon6", "fsl,imx6q";
>
> Missing hardware vendor prefix before "mccmon6".
"lwn,mccmon6" ?
>
> > +
> > + memory {
> > + reg = <0x10000000 0x80000000>;
> > + };
> > +
> > + ethernet0 {
> > + status = "okay";
> > + };
>
> It looks like a useless device node, you have a description of &fec
> already.
>
> > +
> > + backlight_lvds: backlight {
> > + compatible = "pwm-backlight";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_display>;
>
> I would recommend to rename "pinctrl_display" to "pinctrl_backlight".
>
> > + pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
>
> This should work when extension to the i.MX PWM driver is merged.
Yes. The PWM -> apply is an ongoing work. But without the PMW patch the
board is also fully operational (with reversed PWM :-) )
>
> > + brightness-levels = < 0 1 2 3 4 5 6
> > 7 8 9
> > + 10 11 12 13 14 15 16
> > 17 18 19
> > + 20 21 22 23 24 25 26
> > 27 28 29
> > + 30 31 32 33 34 35 36
> > 37 38 39
> > + 40 41 42 43 44 45 46
> > 47 48 49
> > + 50 51 52 53 54 55 56
> > 57 58 59
> > + 60 61 62 63 64 65 66
> > 67 68 69
> > + 70 71 72 73 74 75 76
> > 77 78 79
> > + 80 81 82 83 84 85 86
> > 87 88 89
> > + 90 91 92 93 94 95 96
> > 97 98 99
> > + 100 101 102 103 104 105 106
> > 107 108 109
> > + 110 111 112 113 114 115 116
> > 117 118 119
> > + 120 121 122 123 124 125 126
> > 127 128 129
> > + 130 131 132 133 134 135 136
> > 137 138 139
> > + 140 141 142 143 144 145 146
> > 147 148 149
> > + 150 151 152 153 154 155 156
> > 157 158 159
> > + 160 161 162 163 164 165 166
> > 167 168 169
> > + 170 171 172 173 174 175 176
> > 177 178 179
> > + 180 181 182 183 184 185 186
> > 187 188 189
> > + 190 191 192 193 194 195 196
> > 197 198 199
> > + 200 201 202 203 204 205 206
> > 207 208 209
> > + 210 211 212 213 214 215 216
> > 217 218 219
> > + 220 221 222 223 224 225 226
> > 227 228 229
> > + 230 231 232 233 234 235 236
> > 237 238 239
> > + 240 241 242 243 244 245 246
> > 247 248 249
> > + 250 251 252 253 254 255>;
>
> I'm not sure that actually need such a long list of brightness levels.
Such brightness-level property is so verbose on purpose - in this board
we need fine brightness adjustment (harsh environment operation).
>
> > + default-brightness-level = <50>;
> > + enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + reg_lvds: regulator-lvds {
> > + compatible = "regulator-fixed";
> > + regulator-name = "lvds_ppen";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + panel-lvds0 {
> > + compatible = "innolux,g121x1-l03";
> > + backlight = <&backlight_lvds>;
> > + power-supply = <®_lvds>;
> > +
> > + port {
> > + panel_in_lvds0: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + pmic: pfuze100 at 08 {
> > + compatible = "fsl,pfuze100";
> > + reg = <0x08>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt =
> > <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt =
> > <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt =
> > <3950000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3a_reg: sw3a {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt =
> > <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3b_reg: sw3b {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt =
> > <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt =
> > <3300000>;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt =
> > <5000000>;
> > + regulator-max-microvolt =
> > <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt =
> > <1000000>;
> > + regulator-max-microvolt =
> > <3000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt =
> > <1550000>;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt =
> > <1550000>;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt =
> > <1800000>;
> > + regulator-max-microvolt =
> > <3300000>;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt =
> > <1800000>;
> > + regulator-max-microvolt =
> > <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt =
> > <1800000>;
> > + regulator-max-microvolt =
> > <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt =
> > <1800000>;
> > + regulator-max-microvolt =
> > <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > +
> > + imx6q-mccmon6 {
> > +
>
> Please drop the empty line above.
>
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> > + MX6QDL_PAD_GPIO_16__ENET_REF_CLK
> > 0x4001b0a8
> > +
> > MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> > +
> > MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> > +
> > MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> > +
> > MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> > +
> > MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> > +
> > MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> > +
> > MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> > +
> > MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> > +
> > MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> > +
> > MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> > +
> > MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_weim_cs0: weimcs0grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
> > + >;
> > + };
> > +
> > + pinctrl_weim_nor: weimnorgrp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
> > +
> > MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
> > +
> > MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
> > +
> > MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
> > +
> > MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
> > +v4.9-release-devel-fast
> > MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
> > +
> > MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
> > +
> > MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi3: ecspi3grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> > +
> > MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> > +
> > MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi3_cs: ecspi3cs {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24
> > 0x80000000
> > + >;
> > + };
> > + pinctrl_ecspi3_flwp: ecspi3flwp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27
> > 0x80000000
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> > +
> > MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> > +
> > MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
> > +
> > MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_display: dispgrp {
> > + fsl,pins = <
> > + /* BLEN_OUT */
> > + MX6QDL_PAD_GPIO_2__GPIO1_IO02
> > 0x1b0b0
> > + /* LVDS_PPEN_OUT */
> > + MX6QDL_PAD_SD1_DAT2__GPIO1_IO19
> > 0x1b0b0
>
> This GPIO should be moved to a pinctrl group of regulator-lvds device
> node.
You mean to provide separate:
pinctrl_reg_lvds: req_lvds_grp {
fsl,pins = <
/* LVDS_PPEN_OUT */
MX6QDL_PAD_SD1_DAT2__GPIO1_IO19
>;
and then
reg_lvds: regulator-lvds {
compatible = "regulator-fixed";
regulator-name = "lvds_ppen";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_lvds>;
gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
>
> > + >;
> > + };
> > +
> > + pinctrl_pwm2: pwm2grp {
> > + fsl,pins = <
> > +
> > MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
> > + >;
> > + };
>
> Please sort out all pinctrl_* nodes alphabetically.
>
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + phy-reset-gpios = <&gpio1 27 0>;
>
> GPIO1_27 has no pad configuration in pinctrl_enet.
>
> > + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
> > + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
>
> Should you add "uart-has-rtscts" property?
This is a simple "console" uart without rts/cts, so this property is
not needed.
>
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
>
> bus-width = <4>;
>
> You should consider to add the GPIO1_4 into pinctrl_usdhc2 group.
Added.
>
> > + status = "okay";
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + bus-width = <8>;
> > + status = "okay";
>
> No "cd-gpios" property, should you add "non-removable" property then?
Yes, this is the eMMC memory.
>
> > +};
> > +
> > +&weim {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
> > + #address-cells = <2>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0x08000000 0x08000000>;
> > + status = "okay";
> > +
> > + nor at 0,0 {
> > + compatible = "cfi-flash";
> > + reg = <0 0 0x02000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + bank-width = <2>;
> > + use-advanced-sector-protection;
> > + fsl,weim-cs-timing = <0x00620081 0x00000001
> > 0x1c022000
> > + 0x0000c000 0x1404a38e 0x00000000>;
> > + };
> > +};
> > +
> > +&ecspi3 {
> > + fsl,spi-num-chipselects = <1>;
>
> This property is obsoleted, please remove it.
>
> > + cs-gpios = <&gpio4 24 0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs
> > &pinctrl_ecspi3_flwp>;
> > + status = "okay";
> > +
> > + flash: s25sl032p at 0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "spansion,s25sl032p", "jedec,spi-nor";
> > + spi-max-frequency = <40000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > + status = "okay";
>
> Should you add "uart-has-rtscts" property?
Yes, this uart supports rts/cts flow controll
>
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds0: lvds-channel at 0 {
> > + fsl,data-mapping = "spwg";
> > + fsl,data-width = <24>;
> > + status = "okay";
> > +
> > + port at 4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint =
> > <&panel_in_lvds0>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&pwm2 {
> > + #pwm-cells = <3>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm2>;
> > + status = "okay";
> > +};
> >
>
> Please sort out all device nodes but &iomuxc alphabetically:
>
> * iomuxc
> * ecspi3
> * fec
> * i2c1
> * i2c2
> * ldb
> * pwm2
> * uart1
> * uart4
> * usdhc2
> * usdhc3
> * weim
Ok.
>
> --
> With best wishes,
> Vladimir
Best regards,
Łukasz Majewski
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 181 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170102/096b34d3/attachment-0001.sig>
More information about the linux-arm-kernel
mailing list