[PATCH 1/2] arm64:dt:ls1046a: Add TMU device tree support for LS1046A

[Shawn Guo]

On Thu, Dec 08, 2016 at 11:28:25AM +0800, Jia Hongtao wrote:
> Also add nodes and properties for thermal management support.
> 
> Signed-off-by: Jia Hongtao <hongtao.jia at nxp.com>

"arm64: dts: ls1046a: ..." for subject prefix please.  Also, since we
have ls1046a in prefix, the 'for LS1046A' is not needed.

> ---
>  arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 79 ++++++++++++++++++++++++++
>  1 file changed, 79 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
> index 38806ca..40604e9 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
> @@ -45,6 +45,8 @@
>   */
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/thermal/thermal.h>
> +

Unneeded newline.

>  
>  / {
>  	compatible = "fsl,ls1046a";
> @@ -67,6 +69,7 @@
>  			clocks = <&clockgen 1 0>;
>  			next-level-cache = <&l2>;
>  			cpu-idle-states = <&CPU_PH20>;
> +			#cooling-cells = <2>;
>  		};
>  
>  		cpu1: cpu at 1 {
> @@ -279,6 +282,82 @@
>  			clocks = <&sysclk>;
>  		};
>  
> +		tmu: tmu at 1f00000 {
> +			compatible = "fsl,qoriq-tmu";
> +			reg = <0x0 0x1f00000 0x0 0x10000>;
> +			interrupts = <0 33 0x4>;
> +			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
> +			fsl,tmu-calibration = <0x00000000 0x00000026
> +					       0x00000001 0x0000002d
> +					       0x00000002 0x00000032
> +					       0x00000003 0x00000039
> +					       0x00000004 0x0000003f
> +					       0x00000005 0x00000046
> +					       0x00000006 0x0000004d
> +					       0x00000007 0x00000054
> +					       0x00000008 0x0000005a
> +					       0x00000009 0x00000061
> +					       0x0000000a 0x0000006a
> +					       0x0000000b 0x00000071
> +

Instead of a newline, can we have a single line comment here to tell how
these calibration data is grouped?

> +					       0x00010000 0x00000025
> +					       0x00010001 0x0000002c
> +					       0x00010002 0x00000035
> +					       0x00010003 0x0000003d
> +					       0x00010004 0x00000045
> +					       0x00010005 0x0000004e
> +					       0x00010006 0x00000057
> +					       0x00010007 0x00000061
> +					       0x00010008 0x0000006b
> +					       0x00010009 0x00000076
> +
> +					       0x00020000 0x00000029
> +					       0x00020001 0x00000033
> +					       0x00020002 0x0000003d
> +					       0x00020003 0x00000049
> +					       0x00020004 0x00000056
> +					       0x00020005 0x00000061
> +					       0x00020006 0x0000006d
> +
> +					       0x00030000 0x00000021
> +					       0x00030001 0x0000002a
> +					       0x00030002 0x0000003c
> +					       0x00030003 0x0000004e>;
> +			big-endian;
> +			#thermal-sensor-cells = <1>;
> +		};
> +
> +		thermal-zones {
> +			cpu_thermal: cpu-thermal {
> +				polling-delay-passive = <1000>;
> +				polling-delay = <5000>;
> +

We usually do not have newline between properties but nodes, or between
property list and child node.

> +				thermal-sensors = <&tmu 3>;
> +
> +				trips {
> +					cpu_alert: cpu-alert {
> +						temperature = <85000>;
> +						hysteresis = <2000>;
> +						type = "passive";
> +					};

Have a newline here.

Shawn

> +					cpu_crit: cpu-crit {
> +						temperature = <95000>;
> +						hysteresis = <2000>;
> +						type = "critical";
> +					};
> +				};
> +
> +				cooling-maps {
> +					map0 {
> +						trip = <&cpu_alert>;
> +						cooling-device =
> +							<&cpu0 THERMAL_NO_LIMIT
> +							THERMAL_NO_LIMIT>;
> +					};
> +				};
> +			};
> +		};
> +
>  		dspi: dspi at 2100000 {
>  			compatible = "fsl,ls1021a-v1.0-dspi";
>  			#address-cells = <1>;
> -- 
> 2.1.0.27.g96db324
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel