[PATCH] dt: psci: Update DT bindings to support hierarchical PSCI states
Ulf Hansson
ulf.hansson at linaro.org
Thu Dec 28 05:00:01 PST 2017
On 26 December 2017 at 23:13, Rob Herring <robh at kernel.org> wrote:
> On Fri, Dec 22, 2017 at 03:32:07PM +0100, Ulf Hansson wrote:
>> From: Lina Iyer <lina.iyer at linaro.org>
>>
>> Update DT bindings to represent hierarchical CPU and CPU domain idle states
>> for PSCI. Also update the PSCI examples to clearly show how flattened and
>> hierarchical idle states can be represented in DT.
>>
>> Signed-off-by: Lina Iyer <lina.iyer at linaro.org>
>> Signed-off-by: Ulf Hansson <ulf.hansson at linaro.org>
>> ---
>>
>> For your information, I have picked up the work from Lina Iyer around the so
>> called CPU cluster idling series [1,2] and I working on new versions. However,
>> I decided to post the updates to the PSCI DT bindings first, as they will be
>> needed to be agreed upon before further changes can be done to the PSCI firmware
>> driver.
>>
>> Note, these bindings have been discussed over and over again, at LKML, but
>> especially also at various Linux conferences, like LPC and Linaro Connect. We
>> finally came to a conclusion and the changes we agreed upon, should be reflected
>> in this update.
>>
>> Of course, it's a while ago since the latest discussions, but hopefully people
>> don't have too hard time to remember.
>
> Vaguely...
>
>>
>> Kind regards
>> Uffe
>>
>> [1]
>> https://www.spinics.net/lists/arm-kernel/msg566200.html
>>
>> [2]
>> https://lwn.net/Articles/716300/
>>
>> ---
>> Documentation/devicetree/bindings/arm/psci.txt | 152 +++++++++++++++++++++++++
>> 1 file changed, 152 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt
>> index a2c4f1d..5a8f11b 100644
>> --- a/Documentation/devicetree/bindings/arm/psci.txt
>> +++ b/Documentation/devicetree/bindings/arm/psci.txt
>> @@ -105,7 +105,159 @@ Case 3: PSCI v0.2 and PSCI v0.1.
>> ...
>> };
>>
>> +PSCI v1.0 onwards, supports OS-Initiated mode for powering off CPUs and CPU
>> +clusters from the firmware. For such topologies the PSCI firmware driver acts
>> +as pseudo-controller, which may be specified in the psci DT node. The
>> +definitions of the CPU and the CPU cluster topology, must conform to the domain
>> +idle state specification [3]. The domain idle states themselves, must be
>> +compatible with the defined 'domain-idle-state' binding [1], and also need to
>> +specify the arm,psci-suspend-param property for each idle state.
>> +
>> +DT allows representing CPU and CPU cluster idle states in two different ways -
>> +
>> +The flattened model as given in Example 1, lists CPU's idle states followed by
>> +the domain idle state that the CPUs may choose. This is the general practice
>> +followed in PSCI firmwares that support Platform Coordinated mode. Note that
>> +the idle states are all compatible with "arm,idle-state".
>> +
>> +Example 2 represents the hierarchical model of CPU and domain idle states.
>> +CPUs define their domain provider in their DT node. The domain controls the
>> +power to the CPU and possibly other h/w blocks that would be powered off when
>> +the CPU is powered off. The CPU's idle states may therefore be considered as
>> +the domain's idle states and have the compatible "arm,idle-state". Such domains
>> +may be embedded within another domain that represents common h/w blocks between
>> +these CPUs viz. the cluster. The idle states of the cluster would be
>> +represented as the domain's idle states. In order to use OS-Initiated mode of
>> +PSCI in the firmware, the hierarchical representation must be used.
>> +
>> +Example 1: Flattened representation of CPU and domain idle states
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + CPU0: cpu at 0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + reg = <0x0>;
>> + enable-method = "psci";
>> + cpu-idle-states = <&CPU_PWRDN>, <&CLUSTER_RET>,
>> + <&CLUSTER_PWR_DWN>;
>> + };
>> +
>> + CPU1: cpu at 1 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a57", "arm,armv8";
>> + reg = <0x100>;
>> + enable-method = "psci";
>> + cpu-idle-states = <&CPU_PWRDN>, <&CLUSTER_RET>,
>> + <&CLUSTER_PWR_DWN>;
>> + };
>> +
>> + idle-states {
>> + CPU_PWRDN: cpu_power_down{
>
> Use '-' rather than '_'. dtc has more warnings since last time...
Yes, I found this on a couple of more places and fixed them all.
>
>> + compatible = "arm,idle-state";
>> + arm,psci-suspend-param = <0x000001>;
>> + entry-latency-us = <10>;
>> + exit-latency-us = <10>;
>> + min-residency-us = <100>;
>> + };
>> +
>> + CLUSTER_RET: domain_ret {
>> + compatible = "arm,idle-state";
>> + arm,psci-suspend-param = <0x1000010>;
>> + entry-latency-us = <500>;
>> + exit-latency-us = <500>;
>> + min-residency-us = <2000>;
>> + };
>> +
>> + CLUSTER_PWR_DWN: domain_off {
>> + compatible = "arm,idle-state";
>> + arm,psci-suspend-param = <0x1000030>;
>> + entry-latency-us = <2000>;
>> + exit-latency-us = <2000>;
>> + min-residency-us = <6000>;
>> + };
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-0.2";
>> + method = "smc";
>> + };
>> +
>> +Example 2: Hierarchical representation of CPU and domain idle states
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + CPU0: cpu at 0 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + reg = <0x0>;
>> + enable-method = "psci";
>> + power-domains = <&CPU_PD0>;
>> + };
>> +
>> + CPU1: cpu at 1 {
>> + device_type = "cpu";
>> + compatible = "arm,cortex-a57", "arm,armv8";
>> + reg = <0x100>;
>> + enable-method = "psci";
>> + power-domains = <&CPU_PD1>;
>> + };
>> +
>> + idle-states {
>> + CPU_PWRDN: cpu_power_down{
>> + compatible = "arm,idle-state";
>> + arm,psci-suspend-param = <0x000001>;
>> + entry-latency-us = <10>;
>> + exit-latency-us = <10>;
>> + min-residency-us = <100>;
>> + };
>> +
>> + CLUSTER_RET: domain_ret {
>> + compatible = "domain-idle-state";
>> + arm,psci-suspend-param = <0x1000010>;
>> + entry-latency-us = <500>;
>> + exit-latency-us = <500>;
>> + min-residency-us = <2000>;
>> + };
>> +
>> + CLUSTER_PWR_DWN: domain_off {
>> + compatible = "domain-idle-state";
>> + arm,psci-suspend-param = <0x1000030>;
>> + entry-latency-us = <2000>;
>> + exit-latency-us = <2000>;
>> + min-residency-us = <6000>;
>> + };
>> + };
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-1.0";
>> + method = "smc";
>> +
>> + CPU_PD0: cpu-pd at 0 {
>
> A unit address without reg property is now a warning.
There is currently no need for reg property, so let me replace this with:
CPU_PD0: cpu-pd0
>
>> + #power-domain-cells = <0>;
>> + domain-idle-states = <&CPU_PWRDN>;
>> + power-domains = <&CLUSTER_PD>;
>> + };
>> +
>> + CPU_PD1: cpu-pd at 1 {
>> + #power-domain-cells = <0>;
>> + domain-idle-states = <&CPU_PWRDN>;
>> + power-domains = <&CLUSTER_PD>;
>
> Could this node be a child of CLUSTER_PD rather than having a phandle?
> Doesn't matter so much here, but when you have 3 levels?
This follows existing bindings for power-domains as per
Documentation/devicetree/bindings/power/power_domain.txt. I guess it's
better to stick to that!?
>
>> + };
>
> These 2 nodes are identical, so why do you need both?
Each node represents a power domain, which contains devices (in this
case CPUs) that are specific to each power domain.
In other words, we are trying to describe the HW using a hierarchical layout.
>
>> +
>> + CLUSTER_PD: cluster-pd at 0 {
>> + #power-domain-cells = <0>;
>> + domain-idle-states = <&CLUSTER_RET>, <&CLUSTER_PWR_DWN>;
>> + };
>> + };
>> +
>> [1] Kernel documentation - ARM idle states bindings
>> Documentation/devicetree/bindings/arm/idle-states.txt
>> [2] Power State Coordination Interface (PSCI) specification
>> http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf
>> +[3]. PM Domains description
>> + Documentation/devicetree/bindings/power/power_domain.txt
>> --
>> 2.7.4
>>
Kind regards
Uffe
More information about the linux-arm-kernel
mailing list