[PATCH v2 2/3] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

[Yong]

Hi,

On Wed, 27 Dec 2017 23:47:23 +0200
Sakari Ailus <sakari.ailus at iki.fi> wrote:

> Hi Yong,
> 
> On Thu, Dec 21, 2017 at 10:49:35AM +0800, Yong wrote:
> > Hi,
> > 
> > On Tue, 19 Dec 2017 13:53:28 +0200
> > Sakari Ailus <sakari.ailus at iki.fi> wrote:
> > 
> > > Hi Yong,
> > > 
> > > On Thu, Jul 27, 2017 at 01:01:36PM +0800, Yong Deng wrote:
> > > > Add binding documentation for Allwinner V3s CSI.
> > > > 
> > > > Signed-off-by: Yong Deng <yong.deng at magewell.com>
> > > 
> > > DT bindings should precede the driver.
> > 
> > OK.
> > 
> > > 
> > > > ---
> > > >  .../devicetree/bindings/media/sun6i-csi.txt        | 49 ++++++++++++++++++++++
> > > >  1 file changed, 49 insertions(+)
> > > >  create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > 
> > > > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > new file mode 100644
> > > > index 0000000..f8d83f6
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > @@ -0,0 +1,49 @@
> > > > +Allwinner V3s Camera Sensor Interface
> > > > +------------------------------
> > > > +
> > > > +Required properties:
> > > > +  - compatible: value must be "allwinner,sun8i-v3s-csi"
> > > 
> > > What are sun6i and sun8i? Is this device first present in sun6i SoCs,
> > > whereas you have only defined bindings for sun8i?
> > 
> > Yes, some sun6i SoCs has the almost same CSI module.
> > There is only V3s on my hand. So, I only tested it on V3s. But
> > some people work on the others.
> 
> Ack.
> 
> > 
> > > 
> > > > +  - reg: base address and size of the memory-mapped region.
> > > > +  - interrupts: interrupt associated to this IP
> > > > +  - clocks: phandles to the clocks feeding the CSI
> > > > +    * ahb: the CSI interface clock
> > > > +    * mod: the CSI module clock
> > > > +    * ram: the CSI DRAM clock
> > > > +  - clock-names: the clock names mentioned above
> > > > +  - resets: phandles to the reset line driving the CSI
> > > > +
> > > > +- ports: A ports node with endpoint definitions as defined in
> > > > +  Documentation/devicetree/bindings/media/video-interfaces.txt.
> > > 
> > > Please document mandatory and optional endpoint properties relevant for the
> > > hardware.
> > 
> > I have added below commit in my v3:
> > Currently, the driver only support the parallel interface. So, a single port
> > node with one endpoint and parallel bus is supported.
> 
> Please specify the exact properties that are relevant for the hardware. No
> references should be made to the driver, the bindings are entirely
> separate.
> 
> Are the non-parallel (CSI-2?) and parallel bus on the same interface? If
> yes, they should probably use different endpoints, if not, then different
> ports.
> 
> You could document the other bus or omit it now altogether, in which case
> you'd only detail the parallel bus properties here.

Thanks for your explication. I have misunderstood this.

> 
> > 
> > > 
> > > > +
> > > > +Example:
> > > > +
> > > > +	csi1: csi at 01cb4000 {
> > > > +		compatible = "allwinner,sun8i-v3s-csi";
> > > > +		reg = <0x01cb4000 0x1000>;
> > > > +		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > > > +		clocks = <&ccu CLK_BUS_CSI>,
> > > > +			 <&ccu CLK_CSI1_SCLK>,
> > > > +			 <&ccu CLK_DRAM_CSI>;
> > > > +		clock-names = "ahb", "mod", "ram";
> > > > +		resets = <&ccu RST_BUS_CSI>;
> > > > +
> > > > +		port {
> > > > +			#address-cells = <1>;
> > > > +			#size-cells = <0>;
> > > > +
> > > > +			/* Parallel bus endpoint */
> > > > +			csi1_ep: endpoint {
> > > > +				remote-endpoint = <&adv7611_ep>;
> > > > +				bus-width = <16>;
> > > > +				data-shift = <0>;
> > > > +
> > > > +				/* If hsync-active/vsync-active are missing,
> > > > +				   embedded BT.656 sync is used */
> > > > +				hsync-active = <0>; /* Active low */
> > > > +				vsync-active = <0>; /* Active low */
> > > > +				data-active = <1>;  /* Active high */
> > > > +				pclk-sample = <1>;  /* Rising */
> > > > +			};
> > > > +		};
> > > > +	};
> > > > +
> > > 
> > > -- 
> > > Kind regards,
> > > 
> > > Sakari Ailus
> > > e-mail: sakari.ailus at iki.fi
> > 
> > 
> > Thanks,
> > Yong
> 
> -- 
> Regards,
> 
> Sakari Ailus
> e-mail: sakari.ailus at iki.fi


Thanks,
Yong