[PATCH v3 2/6] ARM: dts: imx6: Add initial support for phyBOARD-Mira
Shawn Guo
shawnguo at kernel.org
Tue Dec 26 18:29:49 PST 2017
On Fri, Dec 22, 2017 at 11:59:09AM +0100, Stefan Riedmueller wrote:
> This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
> for PHYTEC phyCORE-i.MX 6.
>
> Signed-off-by: Christian Hemp <c.hemp at phytec.de>
> Signed-off-by: Stefan Christ <s.christ at phytec.de>
> Signed-off-by: Christoph Fritz <chf.fritz at googlemail.com>
> Signed-off-by: Stefan Riedmueller <s.riedmueller at phytec.de>
> ---
> arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 +++++++++++++++++++++++++++++
> 1 file changed, 390 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
>
> diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
> new file mode 100644
> index 0000000..45d8c0c
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
> @@ -0,0 +1,390 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2017 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp at phytec.de>
> + */
> +
> +
> +/ {
> + aliases {
> + rtc0 = &i2c_rtc;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <7>;
> + power-supply = <®_backlight>;
> + pwms = <&pwm1 0 5000000>;
> + status = "okay";
> + };
> +
> + gpio_leds: leds {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpioleds>;
> + status = "disabled";
> +
Generally we do not have newlines in middle of property list.
> + compatible = "gpio-leds";
Please put 'compatible' at the beginning of property list and always
have 'status' be the end of list.
> +
> + red {
> + label = "phyboard-mira:red";
> + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
> + };
> +
> + green {
> + label = "phyboard-mira:green";
> + gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
> + };
> +
> + blue {
> + label = "phyboard-mira:blue";
> + gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + };
> + };
> +
> + reg_backlight: regulator-backlight {
> + compatible = "regulator-fixed";
> + regulator-name = "backlight_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_en_switch: regulator-en-switch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_en_switch>;
> + compatible = "regulator-fixed";
Move the 'compatible' forward.
> + regulator-name = "Enable Switch";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
> + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + };
> +
> + reg_flexcan1: regulator-flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1_en>;
> + compatible = "regulator-fixed";
> + regulator-name = "flexcan1-reg";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_panel: regulator-panel {
> + compatible = "regulator-fixed";
> + regulator-name = "panel-power-supply";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-always-on;
> + };
> +
> + reg_pcie: regulator-pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie_reg>;
> + compatible = "regulator-fixed";
> + regulator-name = "mPCIe_1V5";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_h1_vbus: usb-h1-vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_vbus>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usbotg_vbus: usbotg-vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + panel {
> + compatible = "auo,g104sn02";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_panel_en>;
> + power-supply = <®_panel>;
> + enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
> +
Drop the newline.
Shawn
> + backlight = <&backlight>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + xceiver-supply = <®_flexcan1>;
> + status = "disabled";
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmicec>;
> + ddc-i2c-bus = <&i2c2>;
> + status = "disabled";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + clock-frequency = <400000>;
> + status = "disabled";
> +
> + stmpe: touchctrl at 44 {
> + compatible = "st,stmpe811";
> + reg = <0x44>;
> + interrupt-parent = <&gpio7>;
> + interrupts = <12 IRQ_TYPE_NONE>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_stmpe>;
> + status = "disabled";
> +
> + stmpe_touchscreen {
> + compatible = "st,stmpe-ts";
> + st,sample-time = <4>;
> + st,mod-12b = <1>;
> + st,ref-sel = <0>;
> + st,adc-freq = <1>;
> + st,ave-ctrl = <1>;
> + st,touch-det-delay = <2>;
> + st,settling = <2>;
> + st,fraction-z = <7>;
> + st,i-drive = <1>;
> + };
> + };
> +
> + i2c_rtc: rtc at 68 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rtc_int>;
> + compatible = "microcrystal,rv4162";
> + reg = <0x68>;
> + interrupt-parent = <&gpio7>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + clock-frequency = <100000>;
> + status = "disabled";
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel at 0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "disabled";
> +
> + port at 4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio2 25 GPIO_ACTIVE_LOW>;
> + vpcie-supply = <®_pcie>;
> + status = "disabled";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usb_h1_vbus>;
> + disable-over-current;
> + status = "disabled";
> +};
> +
> +&usbotg {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + vbus-supply = <®_usbotg_vbus>;
> + disable-over-current;
> + status = "disabled";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
> + no-1-8-v;
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + pinctrl_panel_en: panelen1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0xb0b1
> + >;
> + };
> +
> + pinctrl_en_switch: enswitchgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
> + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
> + >;
> + };
> +
> + pinctrl_flexcan1_en: flexcan1engrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0xb0b1
> + >;
> + };
> +
> + pinctrl_gpioleds: gpioledsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x1b0b0
> + >;
> + };
> +
> + pinctrl_hdmicec: hdmicecgrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1
> + >;
> + };
> +
> + pinctrl_pcie_reg: pciereggrp {
> + fsl,pins = <MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0xb0b1>;
> + };
> +
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_rtc_int: rtcintgrp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0
> + >;
> + };
> +
> + pinctrl_stmpe: stmpegrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbh1_vbus: usbh1vbusgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0xb0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> + >;
> + };
> +
> + pinctrl_usbotg_vbus: usbotgvbusgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0xb0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */
> + >;
> + };
> +};
> --
> 2.7.4
>
More information about the linux-arm-kernel
mailing list