[PATCH] arm: dts: mt7623: enable all four available UARTs on bananapi-r2

[Sean Wang]

On Sat, 2017-12-23 at 08:52 +0100, Matthias Brugger wrote:
> 
> On 12/22/2017 07:06 AM, sean.wang at mediatek.com wrote:
> > From: Sean Wang <sean.wang at mediatek.com>
> > 
> > On bpi-r2 board, totally there're four uarts which we usually called
> > uart[0-3] helpful to extend slow I/O devices. Among those ones, uart2 has
> > dedicated pin slot which is used to conolse log. uart[0-1] appear at the
> > 40-pins connector and uart3 has no pinout, but just has test points (TP47
> > for TX and TP48 for RX, respectively) nearby uart2. Also, some missing
> > pinctrl is being complemented for those devices.
> > 
> > Signed-off-by: Sean Wang <sean.wang at mediatek.com>
> > ---
> >  arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 26 ++++++++++++++++++++++++--
> >  1 file changed, 24 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
> > index 7bf5aa2..64bf5db 100644
> > --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
> > +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
> > @@ -409,6 +409,20 @@
> >  				 <MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
> >  		};
> >  	};
> > +
> > +	uart2_pins_a: uart at 2 {
> > +		pins_dat {
> > +			pinmux = <MT7623_PIN_14_GPIO14_FUNC_URXD2>,
> > +				 <MT7623_PIN_15_GPIO15_FUNC_UTXD2>;
> > +		};
> > +	};
> > +
> > +	uart3_pins_a: uart at 3 {
> > +		pins_dat {
> > +			pinmux = <MT7623_PIN_242_URTS2_FUNC_URTS2>,
> > +				 <MT7623_PIN_243_UCTS2_FUNC_UTXD3>;
> > +		};
> > +	};
> >  };
> >  
> >  &pwm {
> > @@ -454,16 +468,24 @@
> >  &uart0 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&uart0_pins_a>;
> > -	status = "disabled";
> > +	status = "okay";
> >  };
> >  
> >  &uart1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&uart1_pins_a>;
> > -	status = "disabled";
> > +	status = "okay";
> >  };
> >  
> >  &uart2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart2_pins_a>;
> > +	status = "okay";
> > +};
> > +
> > +&uart3 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart3_pins_a>;
> >  	status = "okay";
> >  };
> >  
> 
> Why do we want to enable uart3 when there are only test points?
> It is not very useful, or do I oversee something?
> 

I have been listening to the sound from potential users of bpi-r2 to
understand what assistance I have to provide to them. Something could
be seen through [1] in the forum to know they had been trying hard to
explore all available UARTs from the SoC in the last weeks. The patch
should be really useful for these people and for the extra soldering
it shouldn't become a problem for these makers.

[1] http://forum.banana-pi.org/t/gpio-uart-not-the-debug-port/3748

	Sean 


> Regards,
> Matthias
>