[PATCH 2/2] ARM: dts: imx51-babbage: Fix the 26MHz clock modelling

[Shawn Guo]

On Sat, Dec 02, 2017 at 06:26:05PM -0200, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam at nxp.com>
> 
> On imx51-babbage there is a 26MHz oscillator that is gated by GPIO3_1.
> 
> The output of this clock feeds audio codec clock and USB PHY clocks,
> which are gated by GPIO4_26 and GPIO2_1 respectively.
> 
> Fix the clock representation by properly using gpio-gate-clock.
> 
> The clock nodes can be moved out of the 'clocks' node.
> 
> Based on a commit from Lucas Stach for imx51-zii-rdu1 board.
> 
> This also fixes the following build warning with W=1:
> 
> arch/arm/boot/dts/imx51-babbage.dtb: Warning (unit_address_vs_reg): Node /clocks/codec_clock has a reg or ranges property, but no unit name
> 
> Signed-off-by: Fabio Estevam <fabio.estevam at nxp.com>
> ---
>  arch/arm/boot/dts/imx51-babbage.dts | 67 +++++++++++++++++++++++++++----------
>  1 file changed, 50 insertions(+), 17 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
> index c432de7..663a3cd 100644
> --- a/arch/arm/boot/dts/imx51-babbage.dts
> +++ b/arch/arm/boot/dts/imx51-babbage.dts
> @@ -25,18 +25,41 @@
>  		reg = <0x90000000 0x20000000>;
>  	};
>  
> -	clocks {
> -		ckih1 {
> -			clock-frequency = <22579200>;
> -		};
> +	ckih1 {
> +		clock-frequency = <22579200>;
> +	};
>  
> -		clk_26M: codec_clock {
> -			compatible = "fixed-clock";
> -			reg=<0>;
> -			#clock-cells = <0>;
> -			clock-frequency = <26000000>;
> -			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> -		};
> +	clk_26M_osc: 26M_osc {

While at it, I suggest we use hyphen rather than underscore in node
name, and all lowercase for node name.

Shawn

> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <26000000>;
> +	};
> +
> +	clk_26M_osc_gate: 26M_gate {
> +		compatible = "gpio-gate-clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_clk26mhz_osc>;
> +		clocks = <&clk_26M_osc>;
> +		#clock-cells = <0>;
> +		enable-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	clk_26M_audio: audio_gate {
> +		compatible = "gpio-gate-clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_clk26mhz_audio>;
> +		clocks = <&clk_26M_osc_gate>;
> +		#clock-cells = <0>;
> +		enable-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	clk_26M_usb: usbhost_gate {
> +		compatible = "gpio-gate-clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_clk26mhz_usb>;
> +		clocks = <&clk_26M_osc_gate>;
> +		#clock-cells = <0>;
> +		enable-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
>  	};
>  
>  	display1: disp1 {
> @@ -162,7 +185,7 @@
>  		usbh1phy: usbh1phy at 0 {
>  			compatible = "usb-nop-xceiv";
>  			reg = <0>;
> -			clocks = <&clks IMX5_CLK_DUMMY>;
> +			clocks = <&clk_26M_usb>;
>  			clock-names = "main_clk";
>  			reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
>  			vcc-supply = <&vusb_reg>;
> @@ -345,10 +368,8 @@
>  
>  	sgtl5000: codec at a {
>  		compatible = "fsl,sgtl5000";
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&pinctrl_clkcodec>;
>  		reg = <0x0a>;
> -		clocks = <&clk_26M>;
> +		clocks = <&clk_26M_audio>;
>  		VDDA-supply = <&vdig_reg>;
>  		VDDIO-supply = <&vvideo_reg>;
>  	};
> @@ -441,9 +462,21 @@
>  			>;
>  		};
>  
> -		pinctrl_clkcodec: clkcodecgrp {
> +		pinctrl_clk26mhz_audio: clk26mhzaudiocgrp {
> +			fsl,pins = <
> +				MX51_PAD_CSPI1_RDY__GPIO4_26		0x85
> +			>;
> +		};
> +
> +		pinctrl_clk26mhz_osc: clk26mhzoscgrp {
> +			fsl,pins = <
> +				MX51_PAD_DI1_PIN12__GPIO3_1		0x85
> +			>;
> +		};
> +
> +		pinctrl_clk26mhz_usb: clk26mhzusbgrp {
>  			fsl,pins = <
> -				MX51_PAD_CSPI1_RDY__GPIO4_26		0x80000000
> +				MX51_PAD_EIM_D17__GPIO2_1		0x85
>  			>;
>  		};
>  
> -- 
> 2.7.4
>