[PATCH V2 8/9] ARM: dts: stm32: add stm32mp157c initial support
Ludovic Barre
ludovic.Barre at st.com
Mon Dec 18 07:17:51 PST 2017
From: Ludovic Barre <ludovic.barre at st.com>
Add stm32mp157c initial support with:
-Dual Cortex-A7
-Arm psci, timer, gic
-Pinctrl
-Uart
Signed-off-by: Ludovic Barre <ludovic.barre at st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 172 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c.dtsi | 139 ++++++++++++++++++++++++
2 files changed, 311 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c.dtsi
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
new file mode 100644
index 0000000..440276a
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -0,0 +1,172 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre at st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+ soc {
+ pinctrl: pin-controller {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp157-pinctrl";
+ ranges = <0 0x50002000 0xa400>;
+ pins-are-numbered;
+
+ gpioa: gpio at 50002000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x0 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOA";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 0 16>;
+ };
+
+ gpiob: gpio at 50003000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x1000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOB";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 16 16>;
+ };
+
+ gpioc: gpio at 50004000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x2000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOC";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 32 16>;
+ };
+
+ gpiod: gpio at 50005000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x3000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOD";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 48 16>;
+ };
+
+ gpioe: gpio at 50006000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x4000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOE";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 64 16>;
+ };
+
+ gpiof: gpio at 50007000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x5000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOF";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 80 16>;
+ };
+
+ gpiog: gpio at 50008000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x6000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOG";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 96 16>;
+ };
+
+ gpioh: gpio at 50009000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x7000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOH";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 112 16>;
+ };
+
+ gpioi: gpio at 5000a000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x8000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOI";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 128 16>;
+ };
+
+ gpioj: gpio at 5000b000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x9000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOJ";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 144 16>;
+ };
+
+ gpiok: gpio at 5000c000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0xa000 0x400>;
+ clocks = <&clk_pll3_p>;
+ st,bank-name = "GPIOK";
+ ngpios = <8>;
+ gpio-ranges = <&pinctrl 0 160 8>;
+ };
+ };
+
+ pinctrl_z: pin-controller-z {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp157-z-pinctrl";
+ ranges = <0 0x54004000 0x400>;
+ pins-are-numbered;
+ status = "disabled";
+
+ gpioz: gpio at 54004000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x400>;
+ clocks = <&clk_pll2_p>;
+ st,bank-name = "GPIOZ";
+ st,bank-ioport = <11>;
+ ngpios = <8>;
+ gpio-ranges = <&pinctrl_z 0 400 8>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
new file mode 100644
index 0000000..93dbcac
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -0,0 +1,139 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre at st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu1: cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci";
+ method = "smc";
+ cpu_off = <0x84000002>;
+ cpu_on = <0x84000003>;
+ };
+
+ aliases {
+ gpio0 = &gpioa;
+ gpio1 = &gpiob;
+ gpio2 = &gpioc;
+ gpio3 = &gpiod;
+ gpio4 = &gpioe;
+ gpio5 = &gpiof;
+ gpio6 = &gpiog;
+ gpio7 = &gpioh;
+ gpio8 = &gpioi;
+ gpio9 = &gpioj;
+ gpio10 = &gpiok;
+ serial3 = &uart4;
+ };
+
+ intc: interrupt-controller at a0021000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0xa0021000 0x1000>,
+ <0xa0022000 0x2000>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ interrupt-parent = <&intc>;
+ };
+
+ clocks {
+ clk_hse: clk-hse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ clk_pll_per: clk-pll-per {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <64000000>;
+ };
+
+ clk_hsi: clk-hsi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <64000000>;
+ };
+
+ clk_lse: clk-lse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ clk_lsi: clk-lsi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ };
+
+ clk_csi: clk-csi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <4000000>;
+ };
+
+ clk_pclk1: clk-pclk1 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <86000000>;
+ };
+
+ clk_pll3_p: clk-pll3_p {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <172000000>;
+ };
+
+ clk_pll2_p: clk-pll2_p {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <264000000>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+
+ uart4: serial at 40010000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40010000 0x400>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_NONE>;
+ clocks = <&clk_pclk1>;
+ status = "disabled";
+ };
+ };
+};
--
2.7.4
More information about the linux-arm-kernel
mailing list