[PATCH net-next v6 1/2] dt-bindings: net: add DT bindings for Socionext UniPhier AVE

[Kunihiko Hayashi]

Hello Florian,

On Thu, 14 Dec 2017 15:24:17 -0800 <f.fainelli at gmail.com> wrote:
> 
> 
> On 12/14/2017 02:05 AM, Kunihiko Hayashi wrote:
> > DT bindings for the AVE ethernet controller found on Socionext's
> > UniPhier platforms.
> > 
> > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko at socionext.com>
> > Signed-off-by: Jassi Brar <jaswinder.singh at linaro.org>
> > Acked-by: Rob Herring <robh at kernel.org>
> > ---
> >  .../bindings/net/socionext,uniphier-ave4.txt       | 48 ++++++++++++++++++++++
> >  1 file changed, 48 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> > new file mode 100644
> > index 0000000..4700377
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> > @@ -0,0 +1,48 @@
> > +* Socionext AVE ethernet controller
> > +
> > +This describes the devicetree bindings for AVE ethernet controller
> > +implemented on Socionext UniPhier SoCs.
> > +
> > +Required properties:
> > + - compatible: Should be
> > +	- "socionext,uniphier-pro4-ave4" : for Pro4 SoC
> > +	- "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
> > +	- "socionext,uniphier-ld11-ave4" : for LD11 SoC
> > +	- "socionext,uniphier-ld20-ave4" : for LD20 SoC
> > + - reg: Address where registers are mapped and size of region.
> > + - interrupts: Should contain the MAC interrupt.
> > + - phy-mode: See ethernet.txt in the same directory. Allow to choose
> > +	"rgmii", "rmii", or "mii" according to the PHY.
> > + - phy-handle: Should point to the external phy device.
> > +	See ethernet.txt file in the same directory.
> > + - clocks: A phandle to the clock for the MAC.
> > +
> > +Optional properties:
> > + - resets: A phandle to the reset control for the MAC
> > + - local-mac-address: See ethernet.txt in the same directory.
> > +
> > +Required subnode:
> > + - mdio: Device tree subnode with the following required properties:
> > +	- #address-cells: Must be <1>.
> > +	- #size-cells: Must be <0>.
> > +	- reg: phy ID number, usually a small integer.
> 
> Almost, the "reg" property applies to the MDIO child nodes: the Ethernet
> PHYs/MDIO devices. For the MDIO controller itself, the "reg" property,
> if specified, would be relative to the Ethernet controller's base
> register address.
> 
> Please drop this property's description here.

Thank you for pointing out.
Surely this MDIO node doesn't have own "reg" property, and this description
shows "reg" property of PHY device connected to the MDIO bus.

I'll remove the description.

Thank you,

> > +
> > +Example:
> > +
> > +	ether: ethernet at 65000000 {
> > +		compatible = "socionext,uniphier-ld20-ave4";
> > +		reg = <0x65000000 0x8500>;
> > +		interrupts = <0 66 4>;
> > +		phy-mode = "rgmii";
> > +		phy-handle = <&ethphy>;
> > +		clocks = <&sys_clk 6>;
> > +		resets = <&sys_rst 6>;
> > +		local-mac-address = [00 00 00 00 00 00];
> > +		mdio {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			ethphy: ethphy at 1 {
> > +				reg = <1>;
> > +			};
> > +		};
> > +	};
> > 
> 
> -- 
> Florian

---
Best Regards,
Kunihiko Hayashi