[PATCH v3 11/16] KVM: Move vcpu_load to arch-specific kvm_arch_vcpu_ioctl_set_guest_debug

[Cornelia Huck]

On Mon,  4 Dec 2017 21:35:33 +0100
Christoffer Dall <cdall at kernel.org> wrote:

> From: Christoffer Dall <christoffer.dall at linaro.org>
> 
> Move vcpu_load() and vcpu_put() into the architecture specific
> implementations of kvm_arch_vcpu_ioctl_set_guest_debug().
> 
> Reviewed-by: David Hildenbrand <david at redhat.com>
> Signed-off-by: Christoffer Dall <christoffer.dall at linaro.org>
> ---
>  arch/arm64/kvm/guest.c    | 15 ++++++++++++---
>  arch/powerpc/kvm/book3s.c |  2 ++
>  arch/powerpc/kvm/booke.c  | 19 +++++++++++++------
>  arch/s390/kvm/kvm-s390.c  | 16 ++++++++++++----
>  arch/x86/kvm/x86.c        |  4 +++-
>  virt/kvm/kvm_main.c       |  2 --
>  6 files changed, 42 insertions(+), 16 deletions(-)
> 

> diff --git a/arch/powerpc/kvm/booke.c b/arch/powerpc/kvm/booke.c
> index 1b491b89cd43..7cb0e2677e60 100644
> --- a/arch/powerpc/kvm/booke.c
> +++ b/arch/powerpc/kvm/booke.c
> @@ -2018,12 +2018,15 @@ int kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
>  {
>  	struct debug_reg *dbg_reg;
>  	int n, b = 0, w = 0;
> +	int ret = 0;
> +
> +	vcpu_load(vcpu);
>  
>  	if (!(dbg->control & KVM_GUESTDBG_ENABLE)) {
>  		vcpu->arch.dbg_reg.dbcr0 = 0;
>  		vcpu->guest_debug = 0;
>  		kvm_guest_protect_msr(vcpu, MSR_DE, false);
> -		return 0;
> +		goto out;
>  	}
>  
>  	kvm_guest_protect_msr(vcpu, MSR_DE, true);
> @@ -2055,8 +2058,9 @@ int kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
>  #endif
>  
>  	if (!(vcpu->guest_debug & KVM_GUESTDBG_USE_HW_BP))
> -		return 0;
> +		goto out;
>  
> +	ret = -EINVAL;
>  	for (n = 0; n < (KVMPPC_BOOKE_IAC_NUM + KVMPPC_BOOKE_DAC_NUM); n++) {
>  		uint64_t addr = dbg->arch.bp[n].addr;
>  		uint32_t type = dbg->arch.bp[n].type;
> @@ -2067,21 +2071,24 @@ int kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
>  		if (type & ~(KVMPPC_DEBUG_WATCH_READ |
>  			     KVMPPC_DEBUG_WATCH_WRITE |
>  			     KVMPPC_DEBUG_BREAKPOINT))
> -			return -EINVAL;
> +			goto out;
>  
>  		if (type & KVMPPC_DEBUG_BREAKPOINT) {
>  			/* Setting H/W breakpoint */
>  			if (kvmppc_booke_add_breakpoint(dbg_reg, addr, b++))
> -				return -EINVAL;
> +				goto out;
>  		} else {
>  			/* Setting H/W watchpoint */
>  			if (kvmppc_booke_add_watchpoint(dbg_reg, addr,
>  							type, w++))
> -				return -EINVAL;
> +				goto out;
>  		}
>  	}
>  
> -	return 0;
> +	ret = 0;

I would probably set the -EINVAL in the individual branches (so it is
clear that something is wrong, and it is not just a benign exit as in
the cases above), but your code is correct as well. Let the powerpc
folks decide.

> +out:
> +	vcpu_put(vcpu);
> +	return ret;
>  }
>  
>  void kvmppc_booke_vcpu_load(struct kvm_vcpu *vcpu, int cpu)

In any case,

Reviewed-by: Cornelia Huck <cohuck at redhat.com>