[Patch v6 12/12] Documention: v4l: Documentation for HEVC CIDs
Smitha T Murthy
smitha.t at samsung.com
Fri Dec 8 01:08:25 PST 2017
Added V4l2 controls for HEVC encoder
Signed-off-by: Smitha T Murthy <smitha.t at samsung.com>
---
Documentation/media/uapi/v4l/extended-controls.rst | 395 +++++++++++++++++++++
1 file changed, 395 insertions(+)
diff --git a/Documentation/media/uapi/v4l/extended-controls.rst b/Documentation/media/uapi/v4l/extended-controls.rst
index a3e81c1..3c92763 100644
--- a/Documentation/media/uapi/v4l/extended-controls.rst
+++ b/Documentation/media/uapi/v4l/extended-controls.rst
@@ -1960,6 +1960,401 @@ enum v4l2_vp8_golden_frame_sel -
1, 2 and 3 corresponding to encoder profiles 0, 1, 2 and 3.
+High Efficiency Video Coding (HEVC/H.265) Control Reference
+-----------------------------------------------------------
+
+The HEVC/H.265 controls include controls for encoding parameters of HEVC/H.265
+video codec.
+
+
+.. _hevc-control-id:
+
+HEVC/H.265 Control IDs
+^^^^^^^^^^^^^^^^^^^^^^
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MIN_QP (integer)``
+ Minimum quantization parameter for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_QP (integer)``
+ Maximum quantization parameter for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_I_FRAME_QP (integer)``
+ Quantization parameter for an I frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_P_FRAME_QP (integer)``
+ Quantization parameter for a P frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_B_FRAME_QP (integer)``
+ Quantization parameter for a B frame for HEVC.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_QP (boolean)``
+ HIERARCHICAL_QP allows host to specify the quantization parameter values
+ for each temporal layer through HIERARCHICAL_QP_LAYER. This is valid only
+ if HIERARCHICAL_CODING_LAYER is greater than 1. Setting the control value
+ to 1 enables setting of the QP values for the layers.
+
+.. _v4l2-hevc-hier-coding-type:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_TYPE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_hier_coding_type -
+ Selects the hierarchical coding type for encoding. Possible values are:
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_B``
+ - Use the B frame for hierarchical coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_HIERARCHICAL_CODING_P``
+ - Use the P frame for hierarchical coding.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_LAYER (integer)``
+ Selects the hierarchical coding layer. In normal encoding
+ (non-hierarchial coding), it should be zero. Possible values are 0 ~ 6.
+ 0 indicates HIERARCHICAL CODING LAYER 0, 1 indicates HIERARCHICAL CODING
+ LAYER 1 and so on.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L0_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 0.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L1_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 1.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L2_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 2.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L3_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 3.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L4_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 4.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L5_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 5.
+ For HEVC it can have a value of 0-51.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L6_QP (integer)``
+ Indicates quantization parameter for hierarchical coding layer 6.
+ For HEVC it can have a value of 0-51.
+
+.. _v4l2-hevc-profile:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_PROFILE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_profile -
+ Select the desired profile for HEVC encoder.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN``
+ - Main profile.
+ * - ``V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN10``
+ - Main 10 profile.
+ * - ``V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN_STILL_PICTURE``
+ - Main still picture profile.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+.. _v4l2-hevc-level:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LEVEL``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_level -
+ Selects the desired level for HEVC encoder.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_1``
+ - Level 1.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_2``
+ - Level 2.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_2_1``
+ - Level 2.1
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_3``
+ - Level 3.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_3_1``
+ - Level 3.1
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_4``
+ - Level 4.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_4_1``
+ - Level 4.1
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_5``
+ - Level 5.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_5_1``
+ - Level 5.1
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_5_2``
+ - Level 5.2
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_6``
+ - Level 6.0
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_6_1``
+ - Level 6.1
+ * - ``V4L2_MPEG_VIDEO_HEVC_LEVEL_6_2``
+ - Level 6.2
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_FRAME_RATE_RESOLUTION (integer)``
+ Indicates the number of evenly spaced subintervals, called ticks, within
+ one second. This is a 16 bit unsigned integer and has a maximum value up to
+ 0xffff and a minimum value of 1.
+
+.. _v4l2-hevc-tier-flag:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_TIER_FLAG``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_tier_flag -
+ TIER_FLAG specifies tiers information of the HEVC encoded picture. Tier
+ were made to deal with applications that differ in terms of maximum bit
+ rate. Setting the flag to 0 selects HEVC tier_flag as Main tier and setting
+ this flag to 1 indicates High tier. High tier is for applications requiring
+ high bit rates.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_TIER_MAIN``
+ - Main tier.
+ * - ``V4L2_MPEG_VIDEO_HEVC_TIER_HIGH``
+ - High tier.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_PARTITION_DEPTH (integer)``
+ Selects HEVC maximum coding unit depth.
+
+.. _v4l2-hevc-loop-filter-mode:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LOOP_FILTER_MODE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_loop_filter_mode -
+ Loop filter mode for HEVC encoder. Possible values are:
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_LOOP_FILTER_MODE_DISABLED``
+ - Loop filter is disabled.
+ * - ``V4L2_MPEG_VIDEO_HEVC_LOOP_FILTER_MODE_ENABLED``
+ - Loop filter is enabled.
+ * - ``V4L2_MPEG_VIDEO_HEVC_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY``
+ - Loop filter is disabled at the slice boundary.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_BETA_OFFSET_DIV2 (integer)``
+ Selects HEVC loop filter beta offset. The valid range is [-6, +6].
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LF_TC_OFFSET_DIV2 (integer)``
+ Selects HEVC loop filter tc offset. The valid range is [-6, +6].
+
+.. _v4l2-hevc-refresh-type:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_REFRESH_TYPE``
+ (enum)
+
+enum v4l2_mpeg_video_hevc_hier_refresh_type -
+ Selects refresh type for HEVC encoder.
+ Host has to specify the period into
+ V4L2_CID_MPEG_VIDEO_HEVC_REFRESH_PERIOD.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_NONE``
+ - Use the B frame for hierarchical coding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_CRA``
+ - Use CRA (Clean Random Access Unit) picture encoding.
+ * - ``V4L2_MPEG_VIDEO_HEVC_REFRESH_IDR``
+ - Use IDR picture encoding.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+
+``V4L2_CID_MPEG_VIDEO_HEVC_REFRESH_PERIOD (integer)``
+ Selects the refresh period for HEVC encoder.
+ This specifies the number of I pictures between two CRA/IDR pictures.
+ This is valid only if REFRESH_TYPE is not 0.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_LOSSLESS_CU (boolean)``
+ Indicates HEVC lossless encoding. Setting it to 0 disables lossless
+ encoding. Setting it to 1 enables lossless encoding.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_CONST_INTRA_PRED (boolean)``
+ Indicates constant intra prediction for HEVC encoder. Specifies the
+ constrained intra prediction in which intra largest coding unit (LCU)
+ prediction is performed by using residual data and decoded samples of
+ neighboring intra LCU only. Setting the value to 1 enables constant intra
+ prediction and setting the value to 0 disables constant inta prediction.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_WAVEFRONT (boolean)``
+ Indicates wavefront parallel processing for HEVC encoder. Setting it to 0
+ disables the feature and setting it to 1 enables the wavefront parallel
+ processing.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_GENERAL_PB (boolean)``
+ Setting the value to 1 enables combination of P and B frame for HEVC
+ encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_TEMPORAL_ID (boolean)``
+ Indicates temporal identifier for HEVC encoder which is enabled by
+ setting the value to 1.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_STRONG_SMOOTHING (boolean)``
+ Indicates bi-linear interpolation is conditionally used in the intra
+ prediction filtering process in the CVS when set to 1. Indicates bi-linear
+ interpolation is not used in the CVS when set to 0.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_MAX_NUM_MERGE_MV_MINUS1 (integer)``
+ Indicates maximum number of merge candidate motion vectors.
+ Values are from zero to four.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_TMV_PREDICTION (boolean)``
+ Indicates temporal motion vector prediction for HEVC encoder. Setting it to
+ 1 enables the prediction. Setting it to 0 disables the prediction.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_WITHOUT_STARTCODE (boolean)``
+ Specifies if HEVC generates a stream with a size of the length field
+ instead of start code pattern. The size of the length field is configurable
+ through the V4L2_CID_MPEG_VIDEO_HEVC_SIZE_OF_LENGTH_FIELD control. Setting
+ the value to 0 disables encoding without startcode pattern. Setting the
+ value to 1 will enables encoding without startcode pattern.
+
+.. _v4l2-hevc-size-of-length-field:
+
+``V4L2_CID_MPEG_VIDEO_HEVC_SIZE_OF_LENGTH_FIELD``
+(enum)
+
+enum v4l2_mpeg_video_hevc_size_of_length_field -
+ Indicates the size of length field.
+ This is valid when encoding WITHOUT_STARTCODE_ENABLE is enabled.
+
+.. raw:: latex
+
+ \begin{adjustbox}{width=\columnwidth}
+
+.. tabularcolumns:: |p{11.0cm}|p{10.0cm}|
+
+.. flat-table::
+ :header-rows: 0
+ :stub-columns: 0
+
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_0``
+ - Generate start code pattern (Normal).
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_1``
+ - Generate size of length field instead of start code pattern and length is 1.
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_2``
+ - Generate size of length field instead of start code pattern and length is 2.
+ * - ``V4L2_MPEG_VIDEO_HEVC_SIZE_4``
+ - Generate size of length field instead of start code pattern and length is 4.
+
+.. raw:: latex
+
+ \end{adjustbox}
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L0_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 0 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L1_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 1 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L2_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 2 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L3_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 3 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L4_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 4 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L5_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 5 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_HEVC_HIER_CODING_L6_BR (integer)``
+ Indicates bit rate for hierarchical coding layer 6 for HEVC encoder.
+
+``V4L2_CID_MPEG_VIDEO_REF_NUMBER_FOR_PFRAMES (integer)``
+ Selects number of P reference pictures required for HEVC encoder.
+ P-Frame can use 1 or 2 frames for reference.
+
+``V4L2_CID_MPEG_VIDEO_PREPEND_SPSPPS_TO_IDR (integer)``
+ Indicates whether to generate SPS and PPS at every IDR. Setting it to 0
+ disables generating SPS and PPS at every IDR. Setting it to one enables
+ generating SPS and PPS at every IDR.
+
+
.. _camera-controls:
Camera Control Reference
--
2.7.4
More information about the linux-arm-kernel
mailing list