[PATCH 8/9] ARM: dts: imx7-colibri: add MCP2515 CAN controller

[Stefan Agner]

On 2017-12-06 16:30, Stefan Agner wrote:
> The Colibri Evaluation Carrier Board provides a MCP2515 CAN
> controller connected via SPI. Note that the i.MX 7 provides
> an internal CAN controller which is much better suited for CAN
> operations. Using the MCP2515 with a Colibri iMX7 module is
> mainly useful to test the SPI interface.
> 
> Signed-off-by: Stefan Agner <stefan at agner.ch>
> ---
>  arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi | 25 +++++++++++++++++++++++++
>  arch/arm/boot/dts/imx7-colibri.dtsi         | 14 +++++++++++++-
>  2 files changed, 38 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> index 87c23b769a08..3d6c282dd258 100644
> --- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> +++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
> @@ -45,6 +45,13 @@
>  		stdout-path = "serial0:115200n8";
>  	};
>  
> +	/* fixed crystal dedicated to mpc258x */
> +	clk16m: clk16m {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <16000000>;
> +	};
> +
>  	panel: panel {
>  		compatible = "edt,et057090dhu";
>  		backlight = <&bl>;
> @@ -99,6 +106,24 @@
>  	status = "okay";
>  };
>  
> +&ecspi3 {
> +	status = "okay";
> +
> +	mcp258x0: mcp258x at 0 {


Just realized that this is somewhat bogus, this should be "mcp2515:
can at 0".

--
Stefan

> +		compatible = "microchip,mcp2515";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_can_int>;
> +		reg = <0>;
> +		clocks = <&clk16m>;
> +		interrupt-parent = <&gpio5>;
> +		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
> +		spi-max-frequency = <10000000>;
> +		vdd-supply = <&reg_3v3>;
> +		xceiver-supply = <&reg_5v0>;
> +		status = "okay";
> +	};
> +};
> +
>  &fec1 {
>  	status = "okay";
>  };
> diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi
> b/arch/arm/boot/dts/imx7-colibri.dtsi
> index 689ff6822634..e1c6da0a65e4 100644
> --- a/arch/arm/boot/dts/imx7-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx7-colibri.dtsi
> @@ -92,6 +92,13 @@
>  	cpu-supply = <&reg_DCDC2>;
>  };
>  
> +&ecspi3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> +	num-cs = <1>;
> +	cs-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
> +};
> +
>  &fec1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_enet1>;
> @@ -313,7 +320,6 @@
>  		fsl,pins = <
>  			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x74 /* SODIMM 55 */
>  			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x74 /* SODIMM 63 */
> -			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
>  			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
>  			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
>  			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
> @@ -400,6 +406,12 @@
>  		>;
>  	};
>  
> +	pinctrl_can_int: can-int-grp {
> +		fsl,pins = <
> +			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
> +		>;
> +	};
> +
>  	pinctrl_enet1: enet1grp {
>  		fsl,pins = <
>  			MX7D_PAD_ENET1_CRS__GPIO7_IO14			0x14