[RESEND PATCH V2] ARM: dts: introduce the sama5d2 ptc ek board
Ludovic Desroches
ludovic.desroches at microchip.com
Thu Dec 7 00:24:53 PST 2017
Add the official SAMA5D2 Peripheral Touch Controller Evaluation
Kit board.
Signed-off-by: Ludovic Desroches <ludovic.desroches at microchip.com>
---
Resend: Put SPDX-License-Identifier at the beginning of the file.
Changes:
- v2:
- remove memory node
- use SPDX-License-Identifier
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 401 ++++++++++++++++++++++++++++++
2 files changed, 402 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 043d7c720d0c..ed60582eb1da 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d27_som1_ek.dtb \
+ at91-sama5d2_ptc_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
at91-tse850-3.dtb \
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
new file mode 100644
index 000000000000..186cb03e2672
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * at91-sama5d2_ptc_ek.dts - Device Tree file for SAMA5D2 PTC EK board
+ *
+ * Copyright (C) 2017 Microchip/Atmel,
+ * 2017 Wenyou Yang <wenyou.yang at microchip.com>
+ * 2017 Ludovic Desroches <ludovic.desroches at microchip.com>
+ */
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Atmel SAMA5D2 PTC EK";
+ compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
+
+ aliases {
+ serial0 = &uart0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+
+ ahb {
+ usb0: gadget at 300000 {
+ atmel,vbus-gpio = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci at 400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioA PIN_PB12 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci at 500000 {
+ status = "okay";
+ };
+
+ ebi: ebi at 10000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand_default>;
+ status = "okay"; /* conflicts with sdmmc1 and qspi0 */
+
+ nand_controller: nand-controller {
+ status = "okay";
+
+ nand at 3 {
+ reg = <0x3 0x0 0x2>;
+ atmel,rb = <0>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap at 0 {
+ label = "bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0xc0000>;
+ };
+
+ bootloaderenv at 0x100000 {
+ label = "bootloader env";
+ reg = <0x100000 0x40000>;
+ };
+
+ bootloaderenvred at 0x140000 {
+ label = "bootloader env redundant";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb at 180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x1f800000>;
+ };
+ };
+ };
+ };
+ };
+
+ sdmmc0: sdio-host at a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ non-removable;
+ mmc-ddr-1_8v;
+ status = "okay";
+ };
+
+ apb {
+ spi0: spi at f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
+ status = "okay";
+ };
+
+ macb0: ethernet at f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy at 1 {
+ reg = <0x1>;
+ interrupt-parent = <&pioA>;
+ interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ uart0: serial at f801c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ uart2: serial at f8024000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ i2c0: i2c at f8028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ status = "okay";
+ };
+
+ flx0: flexcom at f8034000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c2: i2c at 600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ atmel,fifo-size = <16>;
+ status = "okay";
+ };
+ };
+
+ shdwc at f8048010 {
+ atmel,shdwc-debouncer = <976>;
+
+ input at 0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+ };
+
+ watchdog at f8048040 {
+ status = "okay";
+ };
+
+ spi1: spi at fc000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+ status = "okay";
+ };
+
+ i2c1: i2c at fc028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+
+ at24 at 50 {
+ compatible = "24c02";
+ reg = <0x50>;
+ pagesize = <8>;
+ };
+ };
+
+ pinctrl at fc038000 {
+ pinctrl_flx0_default: flx0_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PC6__TWD1>,
+ <PIN_PC7__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PA10__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PB6__GPIO>,
+ <PIN_PB8__GPIO>,
+ <PIN_PB10__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_macb0_default: macb0_default {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PB24__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_nand_default: nand_default {
+ re_we_data {
+ pinmux = <PIN_PA22__D0>,
+ <PIN_PA23__D1>,
+ <PIN_PA24__D2>,
+ <PIN_PA25__D3>,
+ <PIN_PA26__D4>,
+ <PIN_PA27__D5>,
+ <PIN_PA28__D6>,
+ <PIN_PA29__D7>,
+ <PIN_PA30__NWE_NANDWE>,
+ <PIN_PB2__NRD_NANDOE>;
+ bias-pull-up;
+ };
+
+ ale_cle_rdy_cs {
+ pinmux = <PIN_PB0__A21_NANDALE>,
+ <PIN_PB1__A22_NANDCLE>,
+ <PIN_PC8__NANDRDY>,
+ <PIN_PA31__NCS3>;
+ bias-pull-up;
+ };
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ ck_cd_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_spi0_default: spi0_default {
+ pinmux = <PIN_PA14__SPI0_SPCK>,
+ <PIN_PA15__SPI0_MOSI>,
+ <PIN_PA16__SPI0_MISO>,
+ <PIN_PA17__SPI0_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_spi1_default: spi1_default {
+ pinmux = <PIN_PC1__SPI1_SPCK>,
+ <PIN_PC2__SPI1_MOSI>,
+ <PIN_PC3__SPI1_MISO>,
+ <PIN_PC4__SPI1_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_uart0_default: uart0_default {
+ pinmux = <PIN_PB26__URXD0>,
+ <PIN_PB27__UTXD0>;
+ bias-disable;
+ };
+
+ pinctrl_uart2_default: uart2_default {
+ pinmux = <PIN_PD23__URXD2>,
+ <PIN_PD24__UTXD2>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PB12__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PB11__GPIO>;
+ bias-disable;
+ };
+
+ };
+
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ bp1 {
+ label = "PB_USER";
+ gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioA PIN_PB10 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA PIN_PB6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.12.2
More information about the linux-arm-kernel
mailing list