[PATCH] arm64: allwinner: h5: add support for NanoPi NEO Plus 2 board
Antony Antony
antony at phenome.org
Thu Aug 24 16:17:16 PDT 2017
Add initial DT support for NanoPi NEO Plus 2 by FriendlyELEC
Allwinner H5 quad core Cortex A53 with an ARM Mali-450MP GPU
1 GB DDR3 RAM
8GB eMMC flash (Samsung KLM8G1WEPD-B031)
micro SD card slot
Gigabit Ethernet (external RTL8211E-VB-CG chip)
802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
2x USB 2.0 host ports & 2x USB via headers
The DTS is based on OrangePi PC 2, sun50i-h5-orangepi-pc2
Added dwmac-sun8i Gigabit Ethernet support based on
Nano Pi Neo2 DT and the schematics.
Signed-off-by: Antony Antony <antony at phenome.org>
---
Also commited in Armbian
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts | 257 +++++++++++++++++++++
2 files changed, 258 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 108f12c..e6810c8 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
new file mode 100644
index 0000000..69b9879
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
@@ -0,0 +1,257 @@
+/*
+ * Copyright (C) 2017 Antony Antony <antony at phenome.org>
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "FriendlyARM NanoPi NEO Plus2";
+ compatible = "friendlyarm,nanopi-neo-pus2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy at 7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mixer0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&tcon0 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <10000000>;
+ status = "okay";
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition at 100000 {
+ label = "env";
+ reg = <0x100000 0x100000>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB Type-A ports' VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
--
2.9.3
More information about the linux-arm-kernel
mailing list