[PATCH v2] gpio: uniphier: add UniPhier GPIO controller driver
Masahiro Yamada
yamada.masahiro at socionext.com
Mon Aug 21 02:36:55 PDT 2017
This GPIO controller device is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---
Changes in v2:
- Remove +32 offset for parent interrupts to follow the GIC
binding convention
- Let uniphier_gpio_irq_alloc() fail if nr_irqs != 1
- Allocate gpio_chip statically because just one instance is
supported
- Fix suspend and resume hooks
.../devicetree/bindings/gpio/gpio-uniphier.txt | 42 ++
MAINTAINERS | 1 +
drivers/gpio/Kconfig | 7 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-uniphier.c | 591 +++++++++++++++++++++
include/dt-bindings/gpio/uniphier-gpio.h | 18 +
6 files changed, 660 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/gpio-uniphier.txt
create mode 100644 drivers/gpio/gpio-uniphier.c
create mode 100644 include/dt-bindings/gpio/uniphier-gpio.h
diff --git a/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt b/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt
new file mode 100644
index 000000000000..8e3e1fe0d072
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-uniphier.txt
@@ -0,0 +1,42 @@
+UniPhier GPIO controller
+
+Required properties:
+- compatible: Should be one of the following:
+ "socionext,uniphier-ld4-gpio" - for LD4 SoC
+ "socionext,uniphier-pro4-gpio" - for Pro4 SoC
+ "socionext,uniphier-sld8-gpio" - for sLD8 SoC
+ "socionext,uniphier-pro5-gpio" - for Pro5 SoC
+ "socionext,uniphier-pxs2-gpio" - for PXs2/LD6b SoC
+ "socionext,uniphier-ld11-gpio" - for LD11 SoC
+ "socionext,uniphier-ld20-gpio" - for LD20 SoC
+ "socionext,uniphier-pxs3-gpio" - for PXs3 SoC
+- reg: Specifies offset and length of the register set for the device.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be 2. The first cell is the pin number and the second
+ cell is used to specify optional parameters
+- interrupt-parent: Specifies the parent interrupt controller.
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be 2. The first cell defines the interrupt number.
+ The second cell bits[3:0] is used to specify trigger type as follows:
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive
+ Valid combinations are 1, 2, 3, 4, 8.
+- gpio-ranges: Mapping to pin controller pins (as described in gpio.txt)
+
+Optional properties:
+- gpio-ranges-group-names: Used for named gpio ranges (as described in gpio.txt)
+
+Example:
+ gpio: gpio at 55000000 {
+ compatible = "socionext,uniphier-pro4-gpio";
+ reg = <0x55000000 0x200>;
+ interrupt-parent = <&aidet>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl 0 0 0>;
+ gpio-ranges-group-names = "gpio_range";
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 7b84f047b3fd..9a1f94ff99a6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1992,6 +1992,7 @@ F: arch/arm/mm/cache-uniphier.c
F: arch/arm64/boot/dts/socionext/
F: drivers/bus/uniphier-system-bus.c
F: drivers/clk/uniphier/
+F: drivers/gpio/gpio-uniphier.c
F: drivers/i2c/busses/i2c-uniphier*
F: drivers/irqchip/irq-uniphier-aidet.c
F: drivers/pinctrl/uniphier/
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 461d6fc3688b..5f6d2e984bb6 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -465,6 +465,13 @@ config GPIO_TZ1090_PDC
help
Say yes here to support Toumaz Xenif TZ1090 PDC GPIOs.
+config GPIO_UNIPHIER
+ tristate "UniPhier GPIO support"
+ depends on ARCH_UNIPHIER
+ depends on OF_GPIO
+ help
+ Say yes here to support UniPhier GPIOs.
+
config GPIO_VF610
def_bool y
depends on ARCH_MXC && SOC_VF610
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index a9fda6c55113..1de9fdb8cff9 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -129,6 +129,7 @@ obj-$(CONFIG_GPIO_TWL6040) += gpio-twl6040.o
obj-$(CONFIG_GPIO_TZ1090) += gpio-tz1090.o
obj-$(CONFIG_GPIO_TZ1090_PDC) += gpio-tz1090-pdc.o
obj-$(CONFIG_GPIO_UCB1400) += gpio-ucb1400.o
+obj-$(CONFIG_GPIO_UNIPHIER) += gpio-uniphier.o
obj-$(CONFIG_GPIO_VF610) += gpio-vf610.o
obj-$(CONFIG_GPIO_VIPERBOARD) += gpio-viperboard.o
obj-$(CONFIG_GPIO_VR41XX) += gpio-vr41xx.o
diff --git a/drivers/gpio/gpio-uniphier.c b/drivers/gpio/gpio-uniphier.c
new file mode 100644
index 000000000000..3c096b41208d
--- /dev/null
+++ b/drivers/gpio/gpio-uniphier.c
@@ -0,0 +1,591 @@
+/*
+ * Copyright (C) 2017 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro at socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <dt-bindings/gpio/uniphier-gpio.h>
+
+#define UNIPHIER_GPIO_BANK_MASK \
+ GENMASK((UNIPHIER_GPIO_LINES_PER_BANK) - 1, 0)
+
+#define UNIPHIER_GPIO_IRQ_NUM 24
+
+#define UNIPHIER_GPIO_PORT_DATA 0x0 /* data */
+#define UNIPHIER_GPIO_PORT_DIR 0x4 /* direction (1:in, 0:out) */
+#define UNIPHIER_GPIO_IRQ_EN 0x90 /* irq enable */
+#define UNIPHIER_GPIO_IRQ_MODE 0x94 /* irq mode (1: both edge) */
+#define UNIPHIER_GPIO_IRQ_FLT_EN 0x98 /* noise filter enable */
+#define UNIPHIER_GPIO_IRQ_FLT_CYC 0x9c /* noise filter clock cycle */
+
+struct uniphier_gpio_socdata {
+ unsigned int ngpio;
+ bool (*is_valid_irq)(unsigned int hwirq);
+ bool (*is_input_only)(unsigned int offset);
+};
+
+struct uniphier_gpio_priv {
+ struct irq_domain *domain;
+ const struct uniphier_gpio_socdata *socdata;
+ void __iomem *regs;
+ spinlock_t lock;
+ u32 saved_vals[0];
+};
+
+static unsigned int uniphier_gpio_bank_to_reg(unsigned int bank)
+{
+ unsigned int reg;
+
+ reg = (bank + 1) * 8;
+
+ /*
+ * Unfortunately, the GPIO port registers are not contiguous because
+ * offset 0x90-0x9f is used for IRQ. Add 0x10 when crossing the region.
+ */
+ if (reg >= UNIPHIER_GPIO_IRQ_EN)
+ reg += 0x10;
+
+ return reg;
+}
+
+static void uniphier_gpio_get_bank_and_mask(unsigned int offset,
+ unsigned int *bank, u32 *mask)
+{
+ *bank = offset / UNIPHIER_GPIO_LINES_PER_BANK;
+ *mask = BIT(offset % UNIPHIER_GPIO_LINES_PER_BANK);
+}
+
+static void uniphier_gpio_reg_update(struct uniphier_gpio_priv *priv,
+ unsigned int reg, u32 mask, u32 val)
+{
+ unsigned long flags;
+ u32 tmp;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ tmp = readl(priv->regs + reg);
+ tmp &= ~mask;
+ tmp |= mask & val;
+ writel(tmp, priv->regs + reg);
+ spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+static void uniphier_gpio_bank_write(struct gpio_chip *chip, unsigned int bank,
+ unsigned int reg, u32 mask, u32 val)
+{
+ struct uniphier_gpio_priv *priv = gpiochip_get_data(chip);
+
+ if (!mask)
+ return;
+
+ uniphier_gpio_reg_update(priv, uniphier_gpio_bank_to_reg(bank) + reg,
+ mask, val);
+}
+
+static void uniphier_gpio_offset_write(struct gpio_chip *chip,
+ unsigned int offset, unsigned int reg,
+ int val)
+{
+ unsigned int bank;
+ u32 mask;
+
+ uniphier_gpio_get_bank_and_mask(offset, &bank, &mask);
+
+ uniphier_gpio_bank_write(chip, bank, reg, mask, val ? mask : 0);
+}
+
+static int uniphier_gpio_offset_read(struct gpio_chip *chip,
+ unsigned int offset, unsigned int reg)
+{
+ struct uniphier_gpio_priv *priv = gpiochip_get_data(chip);
+ unsigned int bank, reg_offset;
+ u32 mask;
+
+ uniphier_gpio_get_bank_and_mask(offset, &bank, &mask);
+ reg_offset = uniphier_gpio_bank_to_reg(bank) + reg;
+
+ return !!(readl(priv->regs + reg_offset) & mask);
+}
+
+static int uniphier_gpio_get_direction(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ return uniphier_gpio_offset_read(chip, offset, UNIPHIER_GPIO_PORT_DIR);
+}
+
+static int uniphier_gpio_direction_input(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ uniphier_gpio_offset_write(chip, offset, UNIPHIER_GPIO_PORT_DIR, 1);
+
+ return 0;
+}
+
+static int uniphier_gpio_direction_output(struct gpio_chip *chip,
+ unsigned int offset, int val)
+{
+ struct uniphier_gpio_priv *priv = gpiochip_get_data(chip);
+
+ if (priv->socdata->is_input_only &&
+ priv->socdata->is_input_only(offset)) {
+ dev_err(chip->parent, "GPIO%d is input only port\n", offset);
+ return -EINVAL;
+ }
+
+ uniphier_gpio_offset_write(chip, offset, UNIPHIER_GPIO_PORT_DATA, val);
+ uniphier_gpio_offset_write(chip, offset, UNIPHIER_GPIO_PORT_DIR, 0);
+
+ return 0;
+}
+
+static int uniphier_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ return uniphier_gpio_offset_read(chip, offset, UNIPHIER_GPIO_PORT_DATA);
+}
+
+static void uniphier_gpio_set(struct gpio_chip *chip,
+ unsigned int offset, int val)
+{
+ uniphier_gpio_offset_write(chip, offset, UNIPHIER_GPIO_PORT_DATA, val);
+}
+
+static void uniphier_gpio_set_multiple(struct gpio_chip *chip,
+ unsigned long *mask, unsigned long *bits)
+{
+ unsigned int bank, shift, bank_mask, bank_bits;
+ int i;
+
+ for (i = 0; i < chip->ngpio; i += UNIPHIER_GPIO_LINES_PER_BANK) {
+ bank = i / UNIPHIER_GPIO_LINES_PER_BANK;
+ shift = i % BITS_PER_LONG;
+ bank_mask = (mask[BIT_WORD(i)] >> shift) &
+ UNIPHIER_GPIO_BANK_MASK;
+ bank_bits = bits[BIT_WORD(i)] >> shift;
+
+ uniphier_gpio_bank_write(chip, bank, UNIPHIER_GPIO_PORT_DATA,
+ bank_mask, bank_bits);
+ }
+}
+
+static int uniphier_gpio_to_irq(struct gpio_chip *chip, unsigned int offset)
+{
+ struct irq_fwspec fwspec;
+
+ if (offset < UNIPHIER_GPIO_IRQ_OFFSET)
+ return -ENXIO;
+
+ fwspec.fwnode = of_node_to_fwnode(chip->parent->of_node);
+ fwspec.param_count = 2;
+ fwspec.param[0] = offset - UNIPHIER_GPIO_IRQ_OFFSET;
+ fwspec.param[1] = IRQ_TYPE_NONE;
+
+ return irq_create_fwspec_mapping(&fwspec);
+}
+
+static struct gpio_chip uniphier_gpio_chip = {
+ .label = "UniPhier GPIO",
+ .request = gpiochip_generic_request,
+ .free = gpiochip_generic_free,
+ .get_direction = uniphier_gpio_get_direction,
+ .direction_input = uniphier_gpio_direction_input,
+ .direction_output = uniphier_gpio_direction_output,
+ .get = uniphier_gpio_get,
+ .set = uniphier_gpio_set,
+ .set_multiple = uniphier_gpio_set_multiple,
+ .to_irq = uniphier_gpio_to_irq,
+ .base = -1,
+};
+
+static void uniphier_gpio_irq_mask(struct irq_data *data)
+{
+ struct uniphier_gpio_priv *priv = data->chip_data;
+ u32 mask = BIT(data->hwirq);
+
+ uniphier_gpio_reg_update(priv, UNIPHIER_GPIO_IRQ_EN, mask, 0);
+
+ return irq_chip_mask_parent(data);
+}
+
+static void uniphier_gpio_irq_unmask(struct irq_data *data)
+{
+ struct uniphier_gpio_priv *priv = data->chip_data;
+ u32 mask = BIT(data->hwirq);
+
+ uniphier_gpio_reg_update(priv, UNIPHIER_GPIO_IRQ_EN, mask, mask);
+
+ return irq_chip_unmask_parent(data);
+}
+
+static int uniphier_gpio_irq_set_type(struct irq_data *data, unsigned int type)
+{
+ struct uniphier_gpio_priv *priv = data->chip_data;
+ u32 mask = BIT(data->hwirq);
+ u32 val = 0;
+
+ if (type == IRQ_TYPE_EDGE_BOTH) {
+ val = mask;
+ type = IRQ_TYPE_EDGE_FALLING;
+ }
+
+ uniphier_gpio_reg_update(priv, UNIPHIER_GPIO_IRQ_MODE, mask, val);
+ /* To enable both edge detection, the noise filter must be enabled. */
+ uniphier_gpio_reg_update(priv, UNIPHIER_GPIO_IRQ_FLT_EN, mask, val);
+
+ return irq_chip_set_type_parent(data, type);
+}
+
+static struct irq_chip uniphier_gpio_irq_chip = {
+ .name = "GPIO",
+ .irq_mask = uniphier_gpio_irq_mask,
+ .irq_unmask = uniphier_gpio_irq_unmask,
+ .irq_eoi = irq_chip_eoi_parent,
+ .irq_set_type = uniphier_gpio_irq_set_type,
+};
+
+static const u32 uniphier_gpio_irq_parent_hwirqs[] = {
+ 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,
+ 154, 155, 156, 157, 158, 217, 218, 219,
+};
+
+static int uniphier_gpio_irq_domain_translate(struct irq_domain *domain,
+ struct irq_fwspec *fwspec,
+ unsigned long *out_hwirq,
+ unsigned int *out_type)
+{
+ if (WARN_ON(fwspec->param_count < 2))
+ return -EINVAL;
+
+ *out_hwirq = fwspec->param[0];
+ *out_type = fwspec->param[1] & IRQ_TYPE_SENSE_MASK;
+
+ return 0;
+}
+
+static int uniphier_gpio_irq_domain_alloc(struct irq_domain *domain,
+ unsigned int virq,
+ unsigned int nr_irqs, void *arg)
+{
+ struct uniphier_gpio_priv *priv = domain->host_data;
+ struct irq_fwspec parent_fwspec;
+ irq_hw_number_t hwirq;
+ unsigned int type;
+ int ret;
+
+ if (WARN_ON(nr_irqs != 1))
+ return -EINVAL;
+
+ ret = uniphier_gpio_irq_domain_translate(domain, arg, &hwirq, &type);
+ if (ret)
+ return ret;
+
+ if (!priv->socdata->is_valid_irq(hwirq))
+ return -ENXIO;
+
+ ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
+ &uniphier_gpio_irq_chip, priv);
+ if (ret)
+ return ret;
+
+ if (type == IRQ_TYPE_EDGE_BOTH)
+ type = IRQ_TYPE_EDGE_FALLING;
+
+ BUILD_BUG_ON(ARRAY_SIZE(uniphier_gpio_irq_parent_hwirqs) >
+ UNIPHIER_GPIO_IRQ_NUM);
+
+ /* parent is UniPhier AIDET */
+ parent_fwspec.fwnode = domain->parent->fwnode;
+ parent_fwspec.param_count = 2;
+ parent_fwspec.param[0] = uniphier_gpio_irq_parent_hwirqs[hwirq];
+ parent_fwspec.param[1] = type;
+
+ return irq_domain_alloc_irqs_parent(domain, virq, 1, &parent_fwspec);
+}
+
+static void uniphier_gpio_irq_domain_activate(struct irq_domain *domain,
+ struct irq_data *data)
+{
+ gpiochip_lock_as_irq(&uniphier_gpio_chip,
+ data->hwirq + UNIPHIER_GPIO_IRQ_OFFSET);
+}
+
+static void uniphier_gpio_irq_domain_deactivate(struct irq_domain *domain,
+ struct irq_data *data)
+{
+ gpiochip_unlock_as_irq(&uniphier_gpio_chip,
+ data->hwirq + UNIPHIER_GPIO_IRQ_OFFSET);
+}
+
+static const struct irq_domain_ops uniphier_gpio_irq_domain_ops = {
+ .alloc = uniphier_gpio_irq_domain_alloc,
+ .free = irq_domain_free_irqs_common,
+ .activate = uniphier_gpio_irq_domain_activate,
+ .deactivate = uniphier_gpio_irq_domain_deactivate,
+ .translate = uniphier_gpio_irq_domain_translate,
+};
+
+static void uniphier_gpio_hw_init(struct uniphier_gpio_priv *priv)
+{
+ /*
+ * To detect both edge interrupts, the noise filter must be enabled.
+ * This filter is intended to remove the noise from the irq lines.
+ * It does not work for GPIO input, so GPIO debounce is not supported.
+ * Unfortunately, the filter period is shared among all irq lines.
+ * Just choose a sensible period here.
+ */
+ writel(0xff, priv->regs + UNIPHIER_GPIO_IRQ_FLT_CYC);
+}
+
+static unsigned int uniphier_gpio_get_nbanks(unsigned int ngpio)
+{
+ return DIV_ROUND_UP(ngpio, UNIPHIER_GPIO_LINES_PER_BANK);
+}
+
+static int uniphier_gpio_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *parent_np;
+ struct irq_domain *parent_domain;
+ struct uniphier_gpio_priv *priv;
+ const struct uniphier_gpio_socdata *data;
+ struct resource *regs;
+ unsigned int nregs;
+ int ret;
+
+ parent_np = of_irq_find_parent(dev->of_node);
+ if (!parent_np)
+ return -ENXIO;
+
+ parent_domain = irq_find_host(parent_np);
+ of_node_put(parent_np);
+ if (!parent_domain)
+ return -EPROBE_DEFER;
+
+ data = of_device_get_match_data(dev);
+ if (WARN_ON(!data || !data->is_valid_irq))
+ return -EINVAL;
+
+ nregs = DIV_ROUND_UP(data->ngpio, UNIPHIER_GPIO_LINES_PER_BANK) * 2 + 3;
+
+ nregs = uniphier_gpio_get_nbanks(data->ngpio) * 2 + 3;
+ priv = devm_kzalloc(dev,
+ sizeof(*priv) + sizeof(priv->saved_vals[0]) * nregs,
+ GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->regs = devm_ioremap_resource(dev, regs);
+ if (IS_ERR(priv->regs))
+ return PTR_ERR(priv->regs);
+
+ spin_lock_init(&priv->lock);
+ priv->socdata = data;
+
+ uniphier_gpio_hw_init(priv);
+
+ uniphier_gpio_chip.parent = dev;
+ uniphier_gpio_chip.ngpio = data->ngpio;
+
+ ret = devm_gpiochip_add_data(dev, &uniphier_gpio_chip, priv);
+ if (ret)
+ return ret;
+
+ priv->domain = irq_domain_add_hierarchy(parent_domain, 0,
+ UNIPHIER_GPIO_IRQ_NUM,
+ dev->of_node,
+ &uniphier_gpio_irq_domain_ops,
+ priv);
+ if (!priv->domain)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+}
+
+static int uniphier_gpio_remove(struct platform_device *pdev)
+{
+ struct uniphier_gpio_priv *priv = platform_get_drvdata(pdev);
+
+ irq_domain_remove(priv->domain);
+
+ return 0;
+}
+
+static int __maybe_unused uniphier_gpio_suspend(struct device *dev)
+{
+ struct uniphier_gpio_priv *priv = dev_get_drvdata(dev);
+ unsigned int nbanks = uniphier_gpio_get_nbanks(priv->socdata->ngpio);
+ u32 *val = priv->saved_vals;
+ unsigned int reg;
+ int i;
+
+ for (i = 0; i < nbanks; i++) {
+ reg = uniphier_gpio_bank_to_reg(i);
+
+ *val++ = readl(priv->regs + reg + UNIPHIER_GPIO_PORT_DATA);
+ *val++ = readl(priv->regs + reg + UNIPHIER_GPIO_PORT_DIR);
+ }
+
+ *val++ = readl(priv->regs + UNIPHIER_GPIO_IRQ_EN);
+ *val++ = readl(priv->regs + UNIPHIER_GPIO_IRQ_MODE);
+ *val++ = readl(priv->regs + UNIPHIER_GPIO_IRQ_FLT_EN);
+
+ return 0;
+}
+
+static int __maybe_unused uniphier_gpio_resume(struct device *dev)
+{
+ struct uniphier_gpio_priv *priv = dev_get_drvdata(dev);
+ unsigned int nbanks = uniphier_gpio_get_nbanks(priv->socdata->ngpio);
+ const u32 *val = priv->saved_vals;
+ unsigned int reg;
+ int i;
+
+ for (i = 0; i < nbanks; i++) {
+ reg = uniphier_gpio_bank_to_reg(i);
+
+ writel(*val++, priv->regs + reg + UNIPHIER_GPIO_PORT_DATA);
+ writel(*val++, priv->regs + reg + UNIPHIER_GPIO_PORT_DIR);
+ }
+
+ writel(*val++, priv->regs + UNIPHIER_GPIO_IRQ_EN);
+ writel(*val++, priv->regs + UNIPHIER_GPIO_IRQ_MODE);
+ writel(*val++, priv->regs + UNIPHIER_GPIO_IRQ_FLT_EN);
+
+ uniphier_gpio_hw_init(priv);
+
+ return 0;
+}
+
+static const struct dev_pm_ops uniphier_gpio_pm_ops = {
+ SET_LATE_SYSTEM_SLEEP_PM_OPS(uniphier_gpio_suspend,
+ uniphier_gpio_resume)
+};
+
+static bool uniphier_ld4_gpio_is_valid_irq(unsigned int hwirq)
+{
+ return hwirq < 16 && hwirq != 13;
+}
+
+static const struct uniphier_gpio_socdata uniphier_ld4_gpio_data = {
+ .ngpio = 136,
+ .is_valid_irq = uniphier_ld4_gpio_is_valid_irq,
+};
+
+static bool uniphier_pro4_gpio_is_valid_irq(unsigned int hwirq)
+{
+ return hwirq < 21;
+}
+
+static const struct uniphier_gpio_socdata uniphier_pro4_gpio_data = {
+ .ngpio = 248,
+ .is_valid_irq = uniphier_pro4_gpio_is_valid_irq,
+};
+
+static bool uniphier_pxs2_gpio_is_valid_irq(unsigned int hwirq)
+{
+ return hwirq < 24;
+}
+
+static const struct uniphier_gpio_socdata uniphier_pxs2_gpio_data = {
+ .ngpio = 232,
+ .is_valid_irq = uniphier_pxs2_gpio_is_valid_irq,
+};
+
+static bool uniphier_ld11_gpio_is_input_only(unsigned int offset)
+{
+ return offset >= 144 && offset <= 151;
+}
+
+static const struct uniphier_gpio_socdata uniphier_ld11_gpio_data = {
+ .ngpio = 200,
+ .is_valid_irq = uniphier_pxs2_gpio_is_valid_irq,
+ .is_input_only = uniphier_ld11_gpio_is_input_only,
+};
+
+static const struct uniphier_gpio_socdata uniphier_ld20_gpio_data = {
+ .ngpio = 205,
+ .is_valid_irq = uniphier_pxs2_gpio_is_valid_irq,
+ .is_input_only = uniphier_ld11_gpio_is_input_only,
+};
+
+static bool uniphier_pxs3_gpio_is_input_only(unsigned int offset)
+{
+ return offset >= 144 && offset <= 161;
+}
+
+static const struct uniphier_gpio_socdata uniphier_pxs3_gpio_data = {
+ .ngpio = 286,
+ .is_valid_irq = uniphier_pxs2_gpio_is_valid_irq,
+ .is_input_only = uniphier_pxs3_gpio_is_input_only,
+};
+
+static const struct of_device_id uniphier_gpio_match[] = {
+ {
+ .compatible = "socionext,uniphier-ld4-gpio",
+ .data = &uniphier_ld4_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro4-gpio",
+ .data = &uniphier_pro4_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-sld8-gpio",
+ .data = &uniphier_ld4_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro5-gpio",
+ .data = &uniphier_pro4_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-gpio",
+ .data = &uniphier_pxs2_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld11-gpio",
+ .data = &uniphier_ld11_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-gpio",
+ .data = &uniphier_ld20_gpio_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs3-gpio",
+ .data = &uniphier_pxs3_gpio_data,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_gpio_match);
+
+static struct platform_driver uniphier_gpio_driver = {
+ .probe = uniphier_gpio_probe,
+ .remove = uniphier_gpio_remove,
+ .driver = {
+ .name = "uniphier-gpio",
+ .of_match_table = uniphier_gpio_match,
+ .pm = &uniphier_gpio_pm_ops,
+ },
+};
+module_platform_driver(uniphier_gpio_driver);
+
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro at socionext.com>");
+MODULE_DESCRIPTION("UniPhier GPIO driver");
+MODULE_LICENSE("GPL");
diff --git a/include/dt-bindings/gpio/uniphier-gpio.h b/include/dt-bindings/gpio/uniphier-gpio.h
new file mode 100644
index 000000000000..9f0ad174f61c
--- /dev/null
+++ b/include/dt-bindings/gpio/uniphier-gpio.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright (C) 2017 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro at socionext.com>
+ */
+
+#ifndef _DT_BINDINGS_GPIO_UNIPHIER_H
+#define _DT_BINDINGS_GPIO_UNIPHIER_H
+
+#define UNIPHIER_GPIO_LINES_PER_BANK 8
+
+#define UNIPHIER_GPIO_IRQ_OFFSET ((UNIPHIER_GPIO_LINES_PER_BANK) * 15)
+
+#define UNIPHIER_GPIO_PORT(bank, line) \
+ ((UNIPHIER_GPIO_LINES_PER_BANK) * (bank) + (line))
+
+#define UNIPHIER_GPIO_IRQ(n) ((UNIPHIER_GPIO_IRQ_OFFSET) + (n))
+
+#endif /* _DT_BINDINGS_GPIO_UNIPHIER_H */
--
2.7.4
More information about the linux-arm-kernel
mailing list