[PATCH v2 4/5] arm64: dts: add RK3399-Q7 (Puma) SoM
Klaus Goger
klaus.goger at theobroma-systems.com
Fri Aug 18 12:34:44 PDT 2017
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit 1.8V interface)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet with on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/2x MIPI-DSI
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Signed-off-by: Klaus Goger <klaus.goger at theobroma-systems.com>
---
Changes in v2:
₋ split SoM parts into it's own dtsi
- use dashes in phandles
- use /delete-node/ before redefining opp-table1
- add comment why opp-table1 is redefined
- use generic node names
- remove deprecated regulator-compatible property
-- suggested by Heiko Stübner <heiko at sntech.de>
- add vqmmc property to sdmmc
- use pcie_clkreqn_cpm instead of pcie_clkreqn
-- suggested by Shawn Lin <shawn.lin at rock-chips.com>
arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi | 546 ++++++++++++++++++++++++++
1 file changed, 546 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
new file mode 100644
index 000000000000..7f657b4e9c4d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
@@ -0,0 +1,546 @@
+/*
+ * Copyright (c) 2017 Theobroma Systems Design und Consulting GmbH
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_module>;
+
+ module-led {
+ label = "module_led";
+ gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ panic-indicator;
+ };
+ };
+
+ /* overwrite the opp-table for CPUB as this board uses a different
+ * regulator (FAN53555) that only allows 10mV steps and therefore
+ * can't reach the operation point target voltages from rk3399-opp.dtsi
+ */
+ /delete-node/ opp-table1;
+ cluster1_opp: opp-table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp00 {
+ opp-hz = /bits/ 64 <408000000>;
+ opp-microvolt = <800000>;
+ clock-latency-ns = <40000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <800000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <816000000>;
+ opp-microvolt = <830000>;
+ opp-suspend;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <880000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <950000>;
+ };
+ opp05 {
+ opp-hz = /bits/ 64 <1416000000>;
+ opp-microvolt = <1030000>;
+ };
+ opp06 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <1100000>;
+ };
+ opp07 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1200000>;
+ };
+ opp08 {
+ opp-hz = /bits/ 64 <1992000000>;
+ opp-microvolt = <1230000>;
+ turbo-mode;
+ };
+ };
+
+ clkin_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "clkin_gmac";
+ #clock-cells = <0>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc1v2_phy: vcc1v2-phy {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v2_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 0>;
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+ status = "okay";
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_RMII_SRC>;
+ assigned-clock-parents = <&clkin_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc1v2_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x10>;
+ rx_delay = <0x10>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <168>;
+ i2c-scl-falling-time-ns = <4>;
+ clock-frequency = <400000>;
+
+ vdd_gpu: regulator at 60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ vin-supply = <&vcc5v0_sys>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1230000>;
+ regulator-ramp-delay = <1000>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+};
+
+ rk808: pmic at 1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc5v0_sys>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc1v8_pmu>;
+
+ regulators {
+ vdd_center: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_center";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_cpu_l";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_ldo1: LDO_REG1 {
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_ldo1";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_hdmi: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_hdmi";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sd: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_ldo5: LDO_REG5 {
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_ldo5";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ldo6: LDO_REG6 {
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc_ldo6";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc0v9_hdmi: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vcc0v9_hdmi";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_efuse: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_efuse";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c7 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ fan: fan at 18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ cooling-min-state = <0>;
+ cooling-max-state = <9>;
+ #cooling-cells = <2>;
+ };
+
+ rtc_twi: rtc at 6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+};
+
+&i2c8 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ vdd_cpu_b: regulator at 60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ vin-supply = <&vcc5v0_sys>;
+ regulator-name = "vdd_cpu_b";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1230000>;
+ regulator-ramp-delay = <1000>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&io_domains {
+ status = "okay";
+ bt656-supply = <&vcc_1v8>;
+ audio-supply = <&vcc_1v8>;
+ sdmmc-supply = <&vcc_sd>;
+ gpio1830-supply = <&vcc_1v8>;
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmu1830-supply = <&vcc_1v8>;
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pinctrl {
+ i2c8 {
+ i2c8_xfer_a: i2c8-xfer {
+ rockchip,pins =
+ <RK_GPIO1 RK_PC4 RK_FUNC_1 &pcfg_pull_up>,
+ <RK_GPIO1 RK_PC5 RK_FUNC_1 &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ led_pin_module: led-module-gpio {
+ rockchip,pins =
+ <RK_GPIO2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins =
+ <RK_GPIO1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins =
+ <RK_GPIO4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
+ status = "okay";
+};
+
+&sdmmc {
+ vqmmc = <&vcc_sd>;
+};
+
+&spi1 {
+ status = "okay";
+
+ norflash: flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
--
2.11.0
More information about the linux-arm-kernel
mailing list