[GIT PULL] Second Round of Renesas ARM Based SoC DT Updates for v4.14

[Simon Horman]

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these second round of Renesas ARM based SoC DT updates for v4.14.

This pull request is based on the previous round of
such requests, tagged as renesas-dt-for-v4.14,
which you have already pulled.


The following changes since commit bf38b9ac16c5c8a82d63c79391dd64c5924fc00b:

  ARM: dts: iwg20m: Correct indentation of mmcif0 properties (2017-07-31 17:10:14 +0200)

are available in the git repository at:

  https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-dt2-for-v4.14

for you to fetch changes up to a4bc74d570a79dbfeb64766b130c0113ac39ec3e:

  ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat string (2017-08-17 11:02:51 +0200)

----------------------------------------------------------------
Second Round of Renesas ARM Based SoC DT Updates for v4.14

* Use newly added Gen-3 fallback compat string

  This is consistent with ongoing efforts to use per-generation
  fallback strings where appropriate across devices found
  on R-Car SoCs. The aim of the effort being to strike a balance
  between the limited information available about the compatibility
  of devices found on different SoCs and the desire to ease enabling
  devices on new SoCs.

  This has no run-time effect due to the presence of a per-SoC
  compat string.

* Enable second CPU core on RZ/G1M (r8a7743)

  The RZ/G1M has two CA15 cores running at up to 1.5GHz

* Enable frequency scaling on RZ/G1M (r8a7743)

* Add six I2C cores to RZ/G1M (r8a7743) SoC DT

  This is a step towards enabling these cores on boards that use this SoC

* Add CEC clock for HDMI transmitter to R-Car M2-W (r8a7791) Koelsch

  Hans Verkuil says "The adv7511 on the Koelsch board has a 12 MHz fixed
  clock for the CEC block. Specify this in the dts to enable CEC support."

* Add PFC support to RZ/G1E (r8a7745) SoC and add Ethernet and SCIF2
  pins to SK-RZG1E board.

  This allows the kernel to control multiplexed pins for Ethernet
  and SCIF2 rather than relying on setup inherited at boot.

----------------------------------------------------------------
Biju Das (3):
      ARM: dts: r8a7743: Add I2C DT support
      ARM: dts: r8a7743: Add APMU node and second CPU core
      ARM: dts: r8a7743: Add OPP table for frequency scaling

Hans Verkuil (1):
      ARM: dts: koelsch: Add CEC clock for HDMI transmitter

Sergei Shtylyov (3):
      ARM: dts: r8a7745: add PFC support
      ARM: dts: sk-rzg1e: add SCIF2 pins
      ARM: dts: sk-rzg1e: add Ether pins

Simon Horman (2):
      ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat string
      ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat string

 arch/arm/boot/dts/r8a7743.dtsi         | 122 +++++++++++++++++++++++++++++++++
 arch/arm/boot/dts/r8a7745-sk-rzg1e.dts |  25 ++++++-
 arch/arm/boot/dts/r8a7745.dtsi         |   7 +-
 arch/arm/boot/dts/r8a7790.dtsi         |   4 +-
 arch/arm/boot/dts/r8a7791-koelsch.dts  |   8 +++
 arch/arm/boot/dts/r8a7791.dtsi         |   4 +-
 6 files changed, 164 insertions(+), 6 deletions(-)