[patch v2 2/2] drivers: jtag: Add Aspeed SoC 24xx and 25xx families JTAG master driver

[Rob Herring]

On Mon, Aug 07, 2017 at 05:17:47PM +0300, Oleksandr Shamray wrote:
> Driver adds support of Aspeed 2500/2400 series SOC JTAG master controller.
> 
> Driver implements the following jtag ops:
> - freq_get;
> - freq_set;
> - status_get;
> - idle;
> - xfer;
> 
> It has been tested on Mellanox system with BMC equipped with
> Aspeed 2520 SoC for programming CPLD devices.
> 
> Signed-off-by: Jiri Pirko <jiri at resnulli.us>
> Signed-off-by: Oleksandr Shamray <oleksandrs at mellanox.com>
> ---
> v1->v2
> Comments pointed by Greg KH <gregkh at linuxfoundation.org>
> - change license type from GPLv2/BSD to GPLv2
> 
> Comments pointed by Neil Armstrong <narmstrong at baylibre.com>
> - Add clk_prepare_enable/clk_disable_unprepare in clock init/deinit
> - Change .compatible to soc-specific compatible names
>   aspeed,aspeed4000-jtag/aspeed5000-jtag
> - Added dt-bindings
> 
> Comments pointed by Arnd Bergmann <arnd at arndb.de>
> - Reorder functions and removed the forward declarations
> - Add static const qualifier to state machine states transitions
> - Change .compatible to soc-specific compatible names
>   aspeed,aspeed4000-jtag/aspeed5000-jtag
> - Add dt-bindings
> 
> Comments pointed by Randy Dunlap <rdunlap at infradead.org>
> - Change module name jtag-aspeed in description in Kconfig
> 
> Comments pointed by kbuild test robot <lkp at intel.com>
> - Remove invalid include <asm/mach-types.h>
> - add resource_size instead of calculation
> ---
>  .../devicetree/bindings/jtag/aspeed-jtag.txt       |   27 +

Please split binding to separate patch.

>  drivers/jtag/Kconfig                               |   13 +
>  drivers/jtag/Makefile                              |    1 +
>  drivers/jtag/jtag-aspeed.c                         |  774 ++++++++++++++++++++
>  4 files changed, 815 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
>  create mode 100644 drivers/jtag/jtag-aspeed.c
> 
> diff --git a/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
> new file mode 100644
> index 0000000..27b1d34
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
> @@ -0,0 +1,27 @@
> +Aspeed JTAG driver for ast2400 and ast2500 SoC
> +
> +Required properties:
> +- compatible:		Should be one of
> +      - "aspeed,aspeed2400-jtag"
> +      - "aspeed,aspeed2500-jtag"
> +- reg			contains the offset and length of the JTAG memory
> +			region
> +- clocks		root clock of bus, should reference the APB clock
> +- reg-shift		device register offsets are shifted by this value

It doesn't appear that you use this. It should be implied by the 
compatible in any case.

> +- interrupts		should contain JTAG controller interrupt
> +
> +Optional properties:
> +- status 		 defines the operation status of the JTAG. Valid
> +values are:
> +      - "disabled"	 the JTAG is disabled
> +      - "okay"		 the JTAG is enabled

Don't need to document status. It's implied for any node.

> +
> +Example:
> +jtag: jtag at 1e6e4000 {
> +	compatible = "aspeed,aspeed2500-jtag";
> +	reg = <0x1e6e4000 0x1c>;
> +	reg-shift = <2>;
> +	clocks = <&clk_apb>;
> +	interrupts = <43>;
> +	status = "disabled";

Don't need to show status in examples either.

> +};
> \ No newline at end of file

^^^