[PATCH] arm64: dts: rockchip: add rk3328-rock64 board
Shawn Lin
shawn.lin at rock-chips.com
Wed Aug 9 18:24:18 PDT 2017
Hi Heiko,
On 2017/8/10 6:04, Heiko Stuebner wrote:
> The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
> Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
> up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
> Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
> devices interface for makers to integrate with sensors and devices.
>
> The devicetree currently supports basic peripherals, with more to be
> added later on.
>
> Signed-off-by: Heiko Stuebner <heiko at sntech.de>
> ---
> Depends on rk805 pmic support landing, which hopefully will happen
> in the next days.
>
> Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 362 +++++++++++++++++++++
> 3 files changed, 367 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
> index 88d95323d301..b54e9bfd9562 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -134,6 +134,10 @@ Rockchip platforms device tree bindings
> Required root node properties:
> - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
>
> +- Pine64 Rock64 board:
> + Required root node properties:
> + - compatible = "pine64,rock64", "rockchip,rk3328";
> +
> - Rockchip PX3 Evaluation board:
> Required root node properties:
> - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index d0ad366bbd12..106fb8e0f2f8 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -1,4 +1,5 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> new file mode 100644
> index 000000000000..a77a94200f96
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
> @@ -0,0 +1,362 @@
> +/*
> + * Copyright (c) 2017 PINE64
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "rk3328.dtsi"
> +
> +/ {
> + model = "Pine64 Rock64";
> + compatible = "pine64,rock64", "rockchip,rk3328";
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + gmac_clkin: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "gmac_clkin";
> + #clock-cells = <0>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> +
> + /*
> + * On the module itself this is one of these (depending
> + * on the actual card populated):
> + * - SDIO_RESET_L_WL_REG_ON
> + * - PDN (power down when low)
> + */
> + reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc_sd: sdmmc-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 30 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0m1_gpio>;
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_host_5v: vcc-host-5v-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb30_host_drv>;
> + regulator-name = "vcc_host_5v";
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb20_host_drv>;
> + regulator-name = "vcc_host1_5v";
> + regulator-always-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_sys: vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + supports-emmc;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + status = "okay";
> +};
> +
supports-{emmc, sd, sdio} aren't vaild properties.
If you do want to speedup the init process and you
could add no-sd and no-sdio for emmc.
num-slots is deprecated and would be cleaned from all dts for 4.14
cycle. And disable-wp is only used for SD card now.
The same comment for the following sd and sdio nodes.
> +&gmac2io {
> + phy-supply = <&vcc_io>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 50000>;
> + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
> + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmiim1_pins>;
> + tx_delay = <0x26>;
> + rx_delay = <0x11>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +
> + rk805: rk805 at 18 {
> + compatible = "rockchip,rk805";
> + reg = <0x18>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk805-clkout2";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_io>;
> + vcc6-supply = <&vcc_sys>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-name = "vdd_logic";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1450000>;
> + regulator-initial-mode = <0x1>;
> + regulator-ramp-delay = <12500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-mode = <0x2>;
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vdd_arm: DCDC_REG2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1450000>;
> + regulator-initial-mode = <0x1>;
> + regulator-ramp-delay = <12500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-mode = <0x2>;
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-initial-mode = <0x1>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-mode = <0x2>;
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_io: DCDC_REG4 {
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <0x1>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-mode = <0x2>;
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_18: LDO_REG1 {
> + regulator-name = "vdd_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc18_emmc: LDO_REG2 {
> + regulator-name = "vcc_18emmc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_10: LDO_REG3 {
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&io_domains {
> + status = "okay";
> +
> + vccio1-supply = <&vcc_io>;
> + vccio2-supply = <&vcc18_emmc>;
> + vccio3-supply = <&vcc_io>;
> + vccio4-supply = <&vcc_18>;
> + vccio5-supply = <&vcc_io>;
> + vccio6-supply = <&vcc_io>;
> + pmuio-supply = <&vcc_io>;
> +};
> +
> +&pinctrl {
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb2 {
> + usb20_host_drv: usb20-host-drv {
> + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb3 {
> + usb30_host_drv: usb30-host-drv {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&sdio {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + disable-wp > + keep-power-in-suspend;
> + max-frequency = <150000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
> + supports-sdio;
> + status = "disabled";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + disable-wp;
> + max-frequency = <150000000>;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
> + supports-sd;
> + vmmc-supply = <&vcc_sd>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +
> + u2phy_host: host-port {
> + status = "okay";
> + };
> +
> + u2phy_otg: otg-port {
> + status = "okay";
> + };
> +};
> +
> +&usb20_otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
>
More information about the linux-arm-kernel
mailing list