[PATCH v3 6/6] dt-bindings: PCI: add support for new generation controller

Bjorn Helgaas helgaas at kernel.org
Tue Aug 8 13:04:51 PDT 2017


On Fri, Aug 04, 2017 at 08:06:42PM +0800, honghui.zhang at mediatek.com wrote:
> From: Ryder Lee <ryder.lee at mediatek.com>
> 
> Add support for MediaTek new generation controller and update related
> properities.

When you update the series, can you update the subject and changelog
to be more specific than "new generation" controller?

Next year there will probably be another "new generation" controller,
so it's useful to be more specific here, e.g., include
"MT2701/MT7623", "MT2712/MT7622", or whatever is appropriate.

> Signed-off-by: Ryder Lee <ryder.lee at mediatek.com>
> Signed-off-by: Honghui Zhang <honghui.zhang at mediatek.com>
> Acked-by: Rob Herring <robh at kernel.org>
> ---
>  .../devicetree/bindings/pci/mediatek-pcie.txt      | 168 ++++++++++++++++++++-
>  1 file changed, 161 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
> index 0fdcb15..2e81742 100644
> --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
> @@ -3,18 +3,31 @@ MediaTek Gen2 PCIe controller
>  Required properties:
>  - compatible: Should contain one of the following strings:
>  	"mediatek,mt2701-pcie"
> +	"mediatek,mt2712-pcie"
> +	"mediatek,mt7622-pcie"
>  	"mediatek,mt7623-pcie"
>  - device_type: Must be "pci"
> -- reg: Base addresses and lengths of the PCIe controller.
> +- reg: Base addresses and lengths of the PCIe subsys and root ports.
> +- reg-names: Names of the above areas to use during resource look-up.
>  - #address-cells: Address representation for root ports (must be 3)
>  - #size-cells: Size representation for root ports (must be 2)
>  - clocks: Must contain an entry for each entry in clock-names.
>    See ../clocks/clock-bindings.txt for details.
> -- clock-names: Must include the following entries:
> -  - free_ck :for reference clock of PCIe subsys
> -  - sys_ck0 :for clock of Port0
> -  - sys_ck1 :for clock of Port1
> -  - sys_ck2 :for clock of Port2
> +- clock-names:
> +  Mandatory entries:
> +   - sys_ckN :transaction layer and data link layer clock
> +  Required entries for MT2701/MT7623:
> +   - free_ck :for reference clock of PCIe subsys
> +  Required entries for MT2712/MT7622:
> +   - ahb_ckN :AHB slave interface operating clock for CSR access and RC
> +	      initiated MMIO access
> +  Required entries for MT7622:
> +   - axi_ckN :application layer MMIO channel operating clock
> +   - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when
> +	      pcie_mac_ck/pcie_pipe_ck is turned off
> +   - obff_ckN :OBFF functional block operating clock
> +   - pipe_ckN :LTSSM and PHY/MAC layer operating clock
> +  where N starting from 0 to one less than the number of root ports.
>  - phys: List of PHY specifiers (used by generic PHY framework).
>  - phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
>    number of PHYs as specified in *phys* property.
> @@ -33,6 +46,10 @@ Required properties for MT7623/MT2701:
>  - reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
>    number of root ports.
>  
> +Required properties for MT2712/MT7622:
> +-interrupts: A list of interrupt outputs of the controller, must have one
> +	     entry for each PCIe port
> +
>  In addition, the device tree node must have sub-nodes describing each
>  PCIe port interface, having the following mandatory properties:
>  
> @@ -50,7 +67,7 @@ Required properties:
>    property is sufficient.
>  - num-lanes: Number of lanes to use for this port.
>  
> -Examples:
> +Examples for MT7623:
>  
>  	hifsys: syscon at 1a000000 {
>  		compatible = "mediatek,mt7623-hifsys",
> @@ -68,6 +85,7 @@ Examples:
>  		      <0 0x1a142000 0 0x1000>, /* Port0 registers */
>  		      <0 0x1a143000 0 0x1000>, /* Port1 registers */
>  		      <0 0x1a144000 0 0x1000>; /* Port2 registers */
> +		reg-names = "subsys", "port0", "port1", "port2";
>  		#address-cells = <3>;
>  		#size-cells = <2>;
>  		#interrupt-cells = <1>;
> @@ -128,3 +146,139 @@ Examples:
>  			num-lanes = <1>;
>  		};
>  	};
> +
> +Examples for MT2712:
> +	pcie: pcie at 11700000 {
> +		compatible = "mediatek,mt2712-pcie";
> +		device_type = "pci";
> +		reg = <0 0x11700000 0 0x1000>,
> +		      <0 0x112ff000 0 0x1000>;
> +		reg-names = "port0", "port1";
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
> +			 <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
> +			 <&pericfg CLK_PERI_PCIE0>,
> +			 <&pericfg CLK_PERI_PCIE1>;
> +		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1";
> +		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
> +		phy-names = "pcie-phy0", "pcie-phy1";
> +		bus-range = <0x00 0xff>;
> +		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
> +
> +		pcie0: pcie at 0,0 {
> +			device_type = "pci";
> +			reg = <0x0000 0 0 0 0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			#interrupt-cells = <1>;
> +			ranges;
> +			num-lanes = <1>;
> +			interrupt-map-mask = <0 0 0 7>;
> +			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
> +					<0 0 0 2 &pcie_intc0 1>,
> +					<0 0 0 3 &pcie_intc0 2>,
> +					<0 0 0 4 &pcie_intc0 3>;
> +			pcie_intc0: interrupt-controller {
> +				interrupt-controller;
> +				#address-cells = <0>;
> +				#interrupt-cells = <1>;
> +			};
> +		};
> +
> +		pcie1: pcie at 1,0 {
> +			device_type = "pci";
> +			reg = <0x0800 0 0 0 0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			#interrupt-cells = <1>;
> +			ranges;
> +			num-lanes = <1>;
> +			interrupt-map-mask = <0 0 0 7>;
> +			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
> +					<0 0 0 2 &pcie_intc1 1>,
> +					<0 0 0 3 &pcie_intc1 2>,
> +					<0 0 0 4 &pcie_intc1 3>;
> +			pcie_intc1: interrupt-controller {
> +				interrupt-controller;
> +				#address-cells = <0>;
> +				#interrupt-cells = <1>;
> +			};
> +		};
> +	};
> +
> +Examples for MT7622:
> +	pcie: pcie at 1a140000 {
> +		compatible = "mediatek,mt7622-pcie";
> +		device_type = "pci";
> +		reg = <0 0x1a140000 0 0x1000>,
> +		      <0 0x1a143000 0 0x1000>,
> +		      <0 0x1a145000 0 0x1000>;
> +		reg-names = "subsys", "port0", "port1";
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
> +		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
> +			 <&pciesys CLK_PCIE_P1_MAC_EN>,
> +			 <&pciesys CLK_PCIE_P0_AHB_EN>,
> +			 <&pciesys CLK_PCIE_P1_AHB_EN>,
> +			 <&pciesys CLK_PCIE_P0_AUX_EN>,
> +			 <&pciesys CLK_PCIE_P1_AUX_EN>,
> +			 <&pciesys CLK_PCIE_P0_AXI_EN>,
> +			 <&pciesys CLK_PCIE_P1_AXI_EN>,
> +			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
> +			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
> +			 <&pciesys CLK_PCIE_P0_PIPE_EN>,
> +			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
> +		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1",
> +			      "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1",
> +			      "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1";
> +		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>;
> +		phy-names = "pcie-phy0", "pcie-phy1";
> +		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
> +		bus-range = <0x00 0xff>;
> +		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
> +
> +		pcie0: pcie at 0,0 {
> +			device_type = "pci";
> +			reg = <0x0000 0 0 0 0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			#interrupt-cells = <1>;
> +			ranges;
> +			num-lanes = <1>;
> +			interrupt-map-mask = <0 0 0 7>;
> +			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
> +					<0 0 0 2 &pcie_intc0 1>,
> +					<0 0 0 3 &pcie_intc0 2>,
> +					<0 0 0 4 &pcie_intc0 3>;
> +			pcie_intc0: interrupt-controller {
> +				interrupt-controller;
> +				#address-cells = <0>;
> +				#interrupt-cells = <1>;
> +			};
> +		};
> +
> +		pcie1: pcie at 1,0 {
> +			device_type = "pci";
> +			reg = <0x0800 0 0 0 0>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			#interrupt-cells = <1>;
> +			ranges;
> +			num-lanes = <1>;
> +			interrupt-map-mask = <0 0 0 7>;
> +			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
> +					<0 0 0 2 &pcie_intc1 1>,
> +					<0 0 0 3 &pcie_intc1 2>,
> +					<0 0 0 4 &pcie_intc1 3>;
> +			pcie_intc1: interrupt-controller {
> +				interrupt-controller;
> +				#address-cells = <0>;
> +				#interrupt-cells = <1>;
> +			};
> +		};
> +	};
> -- 
> 2.6.4
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel



More information about the linux-arm-kernel mailing list