[PATCH v4 1/2] arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2

[Matthias Brugger]

On 08/04/2017 12:14 PM, Sean Wang wrote:
> On Fri, 2017-08-04 at 11:59 +0800, sean.wang at mediatek.com wrote:
>> From: Sean Wang <sean.wang at mediatek.com>
>>
>> The bananapi-r2 board has an SD-card controller and built-in
>> EMMC storage so enables those devices in the devicetree. Also
>> cleanup nodes in alphabetical order in the patch.
>>
> 
> Hi, Matthias
> 
> could your help remove those words "Also cleanup nodes in alphabetical
> order in the patch." when merging, i was forgetting to do it.
> 
> or prefer wanting me to resend it again?

Yes I can do that. No need to resend.

Regards,
Matthias

> 
> 	Sean
> 
>> Signed-off-by: Matthias Brugger <matthias.bgg at gmail.com>
>> Signed-off-by: Sean Wang <sean.wang at mediatek.com>
>> ---
>>   arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 37 +++++++++++++++++++++++++++
>>   1 file changed, 37 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> index 9f3e6dd..444ed93 100644
>> --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> @@ -179,6 +179,32 @@
>>   	status = "okay";
>>   };
>>   
>> +&mmc0 {
>> +	pinctrl-names = "default", "state_uhs";
>> +	pinctrl-0 = <&mmc0_pins_default>;
>> +	pinctrl-1 = <&mmc0_pins_uhs>;
>> +	status = "okay";
>> +	bus-width = <8>;
>> +	max-frequency = <50000000>;
>> +	cap-mmc-highspeed;
>> +	vmmc-supply = <&mt6323_vemc3v3_reg>;
>> +	vqmmc-supply = <&mt6323_vio18_reg>;
>> +	non-removable;
>> +};
>> +
>> +&mmc1 {
>> +	pinctrl-names = "default", "state_uhs";
>> +	pinctrl-0 = <&mmc1_pins_default>;
>> +	pinctrl-1 = <&mmc1_pins_uhs>;
>> +	status = "okay";
>> +	bus-width = <4>;
>> +	max-frequency = <50000000>;
>> +	cap-sd-highspeed;
>> +	cd-gpios = <&pio 261 0>;
>> +	vmmc-supply = <&mt6323_vmch_reg>;
>> +	vqmmc-supply = <&mt6323_vio18_reg>;
>> +};
>> +
>>   &pio {
>>   	cir_pins_a:cir at 0 {
>>   		pins_cir {
>> @@ -314,6 +340,17 @@
>>   			bias-pull-down;
>>   			drive-strength = <MTK_DRIVE_4mA>;
>>   		};
>> +
>> +		pins_wp {
>> +			pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
>> +			input-enable;
>> +			bias-pull-up;
>> +		};
>> +
>> +		pins_insert {
>> +			pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
>> +			bias-pull-up;
>> +		};
>>   	};
>>   
>>   	mmc1_pins_uhs: mmc1 {
> 
>