[PATCH v3] arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2
Matthias Brugger
matthias.bgg at gmail.com
Thu Aug 3 03:03:02 PDT 2017
Hi Sean,
On 08/03/2017 10:38 AM, Sean Wang wrote:
> Hi, Matthias,
>
> Ryder and me tried to make the patch better, so the delivery is made in
> v3, including add missing pin state for mmc1 and remove wp-gpio
> because the board only has micro-sd slot that can't be adjusted for the
> lock manually. And also some cleanups are made for nodes sorted in
> alphabetical order. Thanks for Ryder to catch.
>
Thanks for that. Would you mind to split the clean-up into another patch?
We should avoid patches which do cleanup and adding drivers in one go.
Thanks,
Matthias
> Sean
>
> On Thu, 2017-08-03 at 16:29 +0800, sean.wang at mediatek.com wrote:
>> From: Sean Wang <sean.wang at mediatek.com>
>>
>> The bananapi-r2 board has an SD-card controller and built-in
>> EMMC storage so enables those devices in the devicetree. Also
>> cleanup nodes in alphabetical order in the patch.
>>
>> Signed-off-by: Matthias Brugger <matthias.bgg at gmail.com>
>> Signed-off-by: Sean Wang <sean.wang at mediatek.com>
>> Signed-off-by: Ryder Lee <ryder.lee at mediatek.com>
>> ---
>> arch/arm/boot/dts/mt7623.dtsi | 73 ++++++++++++++-------------
>> arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 73 ++++++++++++++++++++-------
>> 2 files changed, 94 insertions(+), 52 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi
>> index 2a877ed..ec8a074 100644
>> --- a/arch/arm/boot/dts/mt7623.dtsi
>> +++ b/arch/arm/boot/dts/mt7623.dtsi
>> @@ -91,6 +91,7 @@
>> cooling-max-level = <7>;
>> clock-frequency = <1300000000>;
>> };
>> +
>> cpu1: cpu at 1 {
>> device_type = "cpu";
>> compatible = "arm,cortex-a7";
>> @@ -98,6 +99,7 @@
>> operating-points-v2 = <&cpu_opp_table>;
>> clock-frequency = <1300000000>;
>> };
>> +
>> cpu2: cpu at 2 {
>> device_type = "cpu";
>> compatible = "arm,cortex-a7";
>> @@ -105,6 +107,7 @@
>> operating-points-v2 = <&cpu_opp_table>;
>> clock-frequency = <1300000000>;
>> };
>> +
>> cpu3: cpu at 3 {
>> device_type = "cpu";
>> compatible = "arm,cortex-a7";
>> @@ -172,10 +175,12 @@
>> trip = <&cpu_passive>;
>> cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> };
>> +
>> map1 {
>> trip = <&cpu_active>;
>> cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> };
>> +
>> map2 {
>> trip = <&cpu_hot>;
>> cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> @@ -481,6 +486,31 @@
>> nvmem-cell-names = "calibration-data";
>> };
>>
>> + nandc: nfi at 1100d000 {
>> + compatible = "mediatek,mt7623-nfc",
>> + "mediatek,mt2701-nfc";
>> + reg = <0 0x1100d000 0 0x1000>;
>> + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
>> + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
>> + clocks = <&pericfg CLK_PERI_NFI>,
>> + <&pericfg CLK_PERI_NFI_PAD>;
>> + clock-names = "nfi_clk", "pad_clk";
>> + status = "disabled";
>> + ecc-engine = <&bch>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + bch: ecc at 1100e000 {
>> + compatible = "mediatek,mt7623-ecc",
>> + "mediatek,mt2701-ecc";
>> + reg = <0 0x1100e000 0 0x1000>;
>> + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
>> + clocks = <&pericfg CLK_PERI_NFI_ECC>;
>> + clock-names = "nfiecc_clk";
>> + status = "disabled";
>> + };
>> +
>> spi1: spi at 11016000 {
>> compatible = "mediatek,mt7623-spi",
>> "mediatek,mt2701-spi";
>> @@ -509,31 +539,6 @@
>> status = "disabled";
>> };
>>
>> - nandc: nfi at 1100d000 {
>> - compatible = "mediatek,mt7623-nfc",
>> - "mediatek,mt2701-nfc";
>> - reg = <0 0x1100d000 0 0x1000>;
>> - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
>> - power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
>> - clocks = <&pericfg CLK_PERI_NFI>,
>> - <&pericfg CLK_PERI_NFI_PAD>;
>> - clock-names = "nfi_clk", "pad_clk";
>> - status = "disabled";
>> - ecc-engine = <&bch>;
>> - #address-cells = <1>;
>> - #size-cells = <0>;
>> - };
>> -
>> - bch: ecc at 1100e000 {
>> - compatible = "mediatek,mt7623-ecc",
>> - "mediatek,mt2701-ecc";
>> - reg = <0 0x1100e000 0 0x1000>;
>> - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
>> - clocks = <&pericfg CLK_PERI_NFI_ECC>;
>> - clock-names = "nfiecc_clk";
>> - status = "disabled";
>> - };
>> -
>> afe: audio-controller at 11220000 {
>> compatible = "mediatek,mt7623-audio",
>> "mediatek,mt2701-audio";
>> @@ -655,6 +660,15 @@
>> status = "disabled";
>> };
>>
>> + hifsys: syscon at 1a000000 {
>> + compatible = "mediatek,mt7623-hifsys",
>> + "mediatek,mt2701-hifsys",
>> + "syscon";
>> + reg = <0 0x1a000000 0 0x1000>;
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + };
>> +
>> usb1: usb at 1a1c0000 {
>> compatible = "mediatek,mt7623-xhci",
>> "mediatek,mt8173-xhci";
>> @@ -733,15 +747,6 @@
>> };
>> };
>>
>> - hifsys: syscon at 1a000000 {
>> - compatible = "mediatek,mt7623-hifsys",
>> - "mediatek,mt2701-hifsys",
>> - "syscon";
>> - reg = <0 0x1a000000 0 0x1000>;
>> - #clock-cells = <1>;
>> - #reset-cells = <1>;
>> - };
>> -
>> ethsys: syscon at 1b000000 {
>> compatible = "mediatek,mt7623-ethsys",
>> "mediatek,mt2701-ethsys",
>> diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> index 9f3e6dd..0aa1c69 100644
>> --- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> +++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
>> @@ -179,6 +179,32 @@
>> status = "okay";
>> };
>>
>> +&mmc0 {
>> + pinctrl-names = "default", "state_uhs";
>> + pinctrl-0 = <&mmc0_pins_default>;
>> + pinctrl-1 = <&mmc0_pins_uhs>;
>> + status = "okay";
>> + bus-width = <8>;
>> + max-frequency = <50000000>;
>> + cap-mmc-highspeed;
>> + vmmc-supply = <&mt6323_vemc3v3_reg>;
>> + vqmmc-supply = <&mt6323_vio18_reg>;
>> + non-removable;
>> +};
>> +
>> +&mmc1 {
>> + pinctrl-names = "default", "state_uhs";
>> + pinctrl-0 = <&mmc1_pins_default>;
>> + pinctrl-1 = <&mmc1_pins_uhs>;
>> + status = "okay";
>> + bus-width = <4>;
>> + max-frequency = <50000000>;
>> + cap-sd-highspeed;
>> + cd-gpios = <&pio 261 0>;
>> + vmmc-supply = <&mt6323_vmch_reg>;
>> + vqmmc-supply = <&mt6323_vio18_reg>;
>> +};
>> +
>> &pio {
>> cir_pins_a:cir at 0 {
>> pins_cir {
>> @@ -314,6 +340,17 @@
>> bias-pull-down;
>> drive-strength = <MTK_DRIVE_4mA>;
>> };
>> +
>> + pins_wp {
>> + pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
>> + input-enable;
>> + bias-pull-up;
>> + };
>> +
>> + pins_insert {
>> + pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
>> + bias-pull-up;
>> + };
>> };
>>
>> mmc1_pins_uhs: mmc1 {
>> @@ -335,16 +372,6 @@
>> };
>> };
>>
>> - spi0_pins_a: spi at 0 {
>> - pins_spi {
>> - pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>,
>> - <MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>,
>> - <MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>,
>> - <MT7623_PIN_56_SPI0_MO_FUNC_SPI0_MO>;
>> - bias-disable;
>> - };
>> - };
>> -
>> pwm_pins_a: pwm at 0 {
>> pins_pwm {
>> pinmux = <MT7623_PIN_203_PWM0_FUNC_PWM0>,
>> @@ -355,6 +382,16 @@
>> };
>> };
>>
>> + spi0_pins_a: spi at 0 {
>> + pins_spi {
>> + pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>,
>> + <MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>,
>> + <MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>,
>> + <MT7623_PIN_56_SPI0_MO_FUNC_SPI0_MO>;
>> + bias-disable;
>> + };
>> + };
>> +
>> uart0_pins_a: uart at 0 {
>> pins_dat {
>> pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>,
>> @@ -414,14 +451,6 @@
>> status = "disabled";
>> };
>>
>> -&u3phy1 {
>> - status = "okay";
>> -};
>> -
>> -&u3phy2 {
>> - status = "okay";
>> -};
>> -
>> &uart1 {
>> pinctrl-names = "default";
>> pinctrl-0 = <&uart1_pins_a>;
>> @@ -441,3 +470,11 @@
>> vusb33-supply = <&mt6323_vusb_reg>;
>> status = "okay";
>> };
>> +
>> +&u3phy1 {
>> + status = "okay";
>> +};
>> +
>> +&u3phy2 {
>> + status = "okay";
>> +};
>
>
More information about the linux-arm-kernel
mailing list