[PATCH 4/4] dt-bindings: phy-mt65xx-usb: supports PCIe, SATA and rename file
Chunfeng Yun
chunfeng.yun at mediatek.com
Thu Aug 3 03:01:07 PDT 2017
add support for PCIe and SATA, also add some new compatibles.
due to phy-mt65xx-usb.txt holds the bindings for all mediatek SoCs
with T-PHY controller, change the name to phy-mtk-tphy.txt to
reflect that.
Change-Id: I2d9200d4c8768dc301a4c116fe0e9b8179d5911c
Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
---
.../devicetree/bindings/phy/phy-mt65xx-usb.txt | 137 -------------------
.../devicetree/bindings/phy/phy-mtk-tphy.txt | 144 ++++++++++++++++++++
2 files changed, 144 insertions(+), 137 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
create mode 100644 Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt
diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
deleted file mode 100644
index 0acc5a9..0000000
--- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
+++ /dev/null
@@ -1,137 +0,0 @@
-mt65xx USB3.0 PHY binding
---------------------------
-
-This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
-
-Required properties (controller (parent) node):
- - compatible : should be one of
- "mediatek,mt2701-u3phy"
- "mediatek,mt2712-u3phy"
- "mediatek,mt8173-u3phy"
- - clocks : (deprecated, use port's clocks instead) a list of phandle +
- clock-specifier pairs, one for each entry in clock-names
- - clock-names : (deprecated, use port's one instead) must contain
- "u3phya_ref": for reference clock of usb3.0 analog phy.
-
-Required nodes : a sub-node is required for each port the controller
- provides. Address range information including the usual
- 'reg' property is used inside these nodes to describe
- the controller's topology.
-
-Optional properties (controller (parent) node):
- - reg : offset and length of register shared by multiple ports,
- exclude port's private register. It is needed on mt2701
- and mt8173, but not on mt2712.
-
-Required properties (port (child) node):
-- reg : address and length of the register set for the port.
-- clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
-- clock-names : must contain
- "ref": 48M reference clock for HighSpeed analog phy; and 26M
- reference clock for SuperSpeed analog phy, sometimes is
- 24M, 25M or 27M, depended on platform.
-- #phy-cells : should be 1 (See second example)
- cell after port phandle is phy type from:
- - PHY_TYPE_USB2
- - PHY_TYPE_USB3
-
-Example:
-
-u3phy: usb-phy at 11290000 {
- compatible = "mediatek,mt8173-u3phy";
- reg = <0 0x11290000 0 0x800>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
- status = "okay";
-
- u2port0: usb-phy at 11290800 {
- reg = <0 0x11290800 0 0x100>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "ref";
- #phy-cells = <1>;
- status = "okay";
- };
-
- u3port0: usb-phy at 11290900 {
- reg = <0 0x11290800 0 0x700>;
- clocks = <&clk26m>;
- clock-names = "ref";
- #phy-cells = <1>;
- status = "okay";
- };
-
- u2port1: usb-phy at 11291000 {
- reg = <0 0x11291000 0 0x100>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "ref";
- #phy-cells = <1>;
- status = "okay";
- };
-};
-
-Specifying phy control of devices
----------------------------------
-
-Device nodes should specify the configuration required in their "phys"
-property, containing a phandle to the phy port node and a device type;
-phy-names for each port are optional.
-
-Example:
-
-#include <dt-bindings/phy/phy.h>
-
-usb30: usb at 11270000 {
- ...
- phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
- phy-names = "usb2-0", "usb3-0";
- ...
-};
-
-
-Layout differences of banks between mt8173/mt2701 and mt2712
--------------------------------------------------------------
-mt8173 and mt2701:
-port offset bank
-shared 0x0000 SPLLC
- 0x0100 FMREG
-u2 port0 0x0800 U2PHY_COM
-u3 port0 0x0900 U3PHYD
- 0x0a00 U3PHYD_BANK2
- 0x0b00 U3PHYA
- 0x0c00 U3PHYA_DA
-u2 port1 0x1000 U2PHY_COM
-u3 port1 0x1100 U3PHYD
- 0x1200 U3PHYD_BANK2
- 0x1300 U3PHYA
- 0x1400 U3PHYA_DA
-u2 port2 0x1800 U2PHY_COM
- ...
-
-mt2712:
-port offset bank
-u2 port0 0x0000 MISC
- 0x0100 FMREG
- 0x0300 U2PHY_COM
-u3 port0 0x0700 SPLLC
- 0x0800 CHIP
- 0x0900 U3PHYD
- 0x0a00 U3PHYD_BANK2
- 0x0b00 U3PHYA
- 0x0c00 U3PHYA_DA
-u2 port1 0x1000 MISC
- 0x1100 FMREG
- 0x1300 U2PHY_COM
-u3 port1 0x1700 SPLLC
- 0x1800 CHIP
- 0x1900 U3PHYD
- 0x1a00 U3PHYD_BANK2
- 0x1b00 U3PHYA
- 0x1c00 U3PHYA_DA
-u2 port2 0x2000 MISC
- ...
-
- SPLLC shared by u3 ports and FMREG shared by u2 ports on
-mt8173/mt2701 are put back into each port; a new bank MISC for
-u2 ports and CHIP for u3 ports are added on mt2712.
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt
new file mode 100644
index 0000000..faf1808
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt
@@ -0,0 +1,144 @@
+MediaTek T-PHY binding
+--------------------------
+
+T-phy controller supports physical layer functionality for a number of
+controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA.
+
+Required properties (controller (parent) node):
+ - compatible : should be one of
+ "mediatek,generic-tphy-v1"
+ "mediatek,generic-tphy-v2"
+ "mediatek,mt2701-u3phy" (deprecated)
+ "mediatek,mt2712-u3phy" (deprecated)
+ "mediatek,mt8173-u3phy";
+ make use of "mediatek,generic-tphy-v1" on mt2701 instead and
+ "mediatek,generic-tphy-v2" on mt2712 instead.
+ - clocks : (deprecated, use port's clocks instead) a list of phandle +
+ clock-specifier pairs, one for each entry in clock-names
+ - clock-names : (deprecated, use port's one instead) must contain
+ "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes : a sub-node is required for each port the controller
+ provides. Address range information including the usual
+ 'reg' property is used inside these nodes to describe
+ the controller's topology.
+
+Optional properties (controller (parent) node):
+ - reg : offset and length of register shared by multiple ports,
+ exclude port's private register. It is needed on mt2701
+ and mt8173, but not on mt2712.
+
+Required properties (port (child) node):
+- reg : address and length of the register set for the port.
+- clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+- clock-names : must contain
+ "ref": 48M reference clock for HighSpeed analog phy; and 26M
+ reference clock for SuperSpeed analog phy, sometimes is
+ 24M, 25M or 27M, depended on platform.
+- #phy-cells : should be 1 (See second example)
+ cell after port phandle is phy type from:
+ - PHY_TYPE_USB2
+ - PHY_TYPE_USB3
+ - PHY_TYPE_PCIE
+ - PHY_TYPE_SATA
+
+Example:
+
+u3phy: usb-phy at 11290000 {
+ compatible = "mediatek,mt8173-u3phy";
+ reg = <0 0x11290000 0 0x800>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "okay";
+
+ u2port0: usb-phy at 11290800 {
+ reg = <0 0x11290800 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u3port0: usb-phy at 11290900 {
+ reg = <0 0x11290800 0 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u2port1: usb-phy at 11291000 {
+ reg = <0 0x11291000 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb at 11270000 {
+ ...
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+ phy-names = "usb2-0", "usb3-0";
+ ...
+};
+
+
+Layout differences of banks between mt8173/mt2701 and mt2712
+-------------------------------------------------------------
+mt8173 and mt2701:
+port offset bank
+shared 0x0000 SPLLC
+ 0x0100 FMREG
+u2 port0 0x0800 U2PHY_COM
+u3 port0 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 U2PHY_COM
+u3 port1 0x1100 U3PHYD
+ 0x1200 U3PHYD_BANK2
+ 0x1300 U3PHYA
+ 0x1400 U3PHYA_DA
+u2 port2 0x1800 U2PHY_COM
+ ...
+
+mt2712:
+port offset bank
+u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+u3 port0 0x0700 SPLLC
+ 0x0800 CHIP
+ 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+u3 port1 0x1700 SPLLC
+ 0x1800 CHIP
+ 0x1900 U3PHYD
+ 0x1a00 U3PHYD_BANK2
+ 0x1b00 U3PHYA
+ 0x1c00 U3PHYA_DA
+u2 port2 0x2000 MISC
+ ...
+
+ SPLLC shared by u3 ports and FMREG shared by u2 ports on
+mt8173/mt2701 are put back into each port; a new bank MISC for
+u2 ports and CHIP for u3 ports are added on mt2712.
--
1.7.9.5
More information about the linux-arm-kernel
mailing list