[PATCH 1/3] dt-bindings: phy: Add documentation for NS2 USB3 PHY

[Jon Mason]

From: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>

Add documentation for USB3 PHY available in NS2 SoC

Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>
Signed-off-by: Jon Mason <jon.mason at broadcom.com>
---
 .../devicetree/bindings/phy/brcm,ns2-usb3-phy.txt  | 82 ++++++++++++++++++++++
 1 file changed, 82 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-usb3-phy.txt

diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-usb3-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-usb3-phy.txt
new file mode 100644
index 0000000..5bb8d53
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,ns2-usb3-phy.txt
@@ -0,0 +1,82 @@
+Broadcom USB3 dual port phy for Northstar2 SoC
+This is a child bus node of "brcm,mdio-mux-iproc" node.
+
+Required mdio bus properties:
+- reg: MDIO Bus number for the MDIO interface
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Required PHY properties:
+- compatible: should be "brcm,ns2-usb3-phy"
+- reg: Phy address in the MDIO interface
+- usb3-ctrl-syscon: handler of syscon node defining physical address
+  of usb3 control register.
+- usb3-phy-cfg-syscon: handler of syscon node defining physical base
+  address and length of usb3 phy config region.
+- usb3-rst-ctrl-syscon: handler of syscon node defining physical base
+  address and length of idm reset control of two ports.
+- #phy-cells: must be 0
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Sub-nodes:
+  Each port's PHY should be represented as a sub-node.
+
+Sub-nodes required properties:
+ - reg: the PHY number
+ - phy-cells: from the generic PHY bindings, must be 0
+
+Required usb3 control properties:
+- compatible: should be "brcm,ns2-usb3-ctrl"
+- reg: offset and length of the control registers
+
+Required usb3 phy config properties:
+- compatible: should be "brcm,ns2-usb3-phy-cfg"
+- reg: offset and length of the phy config registers
+
+Required usb3 reset control properties:
+- compatible: should be "brcm,ns2-usb3-rst-ctrl"
+- reg: offset and length of the reset control registers
+
+Example:
+
+mdio at 1 {
+	reg = <0x1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb3phy: usb3phy at 0 {
+		compatible = "brcm,ns2-usb3-phy";
+		reg = <0x0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		usb3-ctrl-syscon = <&usb3_ctrl>;
+		usb3-phy-cfg-syscon = <&usb3_phy_cfg>;
+		usb3-rst-ctrl-syscon = <&usb3_rst_ctrl>;
+
+		usb3phy0: usbphy at 0 {
+			reg = <0>;
+			#phy-cells = <0>;
+		};
+
+		usb3phy1: usbphy at 1 {
+			reg = <1>;
+			#phy-cells = <0>;
+		};
+	};
+};
+
+usb3_ctrl: syscon at 6501d144 {
+	compatible = "brcm,ns2-usb3-ctrl", "syscon";
+	reg = <0x6501d144 0x4>;
+};
+
+usb3_phy_cfg: syscon at 66000910 {
+	compatible = "brcm,ns2-usb3-phy-cfg", "syscon";
+	reg = <0x66000910 0x14>;
+};
+
+usb3_rst_ctrl: syscon at 67000800 {
+	compatible = "brcm,ns2-usb3-rst-ctrl", "syscon";
+	reg = <0x67000800 0x1808>;
+};
-- 
2.7.4