[PATCH 4/5] ARM: sun8i: h3: add operating-points-v2 table for CPU

[Maxime Ripard]

On Mon, Apr 17, 2017 at 05:00:00AM +0800, Icenowy Zheng wrote:
> 
> 
> 于 2017年4月17日 GMT+08:00 上午4:57:40, Maxime Ripard <maxime.ripard at free-electrons.com> 写到:
> >On Tue, Apr 11, 2017 at 09:28:55PM +0800, icenowy at aosc.io wrote:
> >> 在 2017-04-11 17:13，Maxime Ripard 写道：
> >> > On Sun, Apr 09, 2017 at 02:50:24AM +0800, Icenowy Zheng wrote:
> >> > > The CPU on Allwinner H3 can do dynamic frequency scaling.
> >> > > 
> >> > > Add a DVFS table based on the one tweaked by Armbian developers,
> >which
> >> > > are proven to work stably on BSP kernels.
> >> > > 
> >> > > Frequencies higher than 1008MHz are temporarily dropped in the
> >> > > table, as
> >> > > they may lead to over voltage on boards without proper regulator
> >> > > settings or over temperature on boards with proper regulator
> >settings.
> >> > > They will be added back once regulator settings are ready and
> >thermal
> >> > > sensor driver is merged.
> >> > > 
> >> > > In order to satisfy all different regulators (SY8106A which is
> >50mV
> >> > > per
> >> > > level, SY8113B which have two states: 1.1V and 1.3V, and some
> >board
> >> > > with
> >> > > non-tweakable regulators), all the OPPs are defined with a range
> >> > > which has
> >> > > the target value as the minimum allowed value, and 1.3V (the
> >highest
> >> > > VDD-CPUX voltage suggested by the datasheet) as the maximum
> >allowed
> >> > > value.
> >> > > It's proven to work well with a board with SY8113B.
> >> > > 
> >> > > Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
> >> > > ---
> >> > >  arch/arm/boot/dts/sun8i-h3.dtsi | 38
> >> > > +++++++++++++++++++++++++++++++++++++-
> >> > >  1 file changed, 37 insertions(+), 1 deletion(-)
> >> > > 
> >> > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi
> >> > > b/arch/arm/boot/dts/sun8i-h3.dtsi
> >> > > index b36f9f423c39..a0cee17fe44b 100644
> >> > > --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> >> > > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> >> > > @@ -43,32 +43,68 @@
> >> > >  #include "sunxi-h3-h5.dtsi"
> >> > > 
> >> > >  / {
> >> > > +	cpu0_opp_table: opp_table0 {
> >> > > +		compatible = "operating-points-v2";
> >> > > +		opp-shared;
> >> > > +
> >> > > +		opp at 480000000 {
> >> > > +			opp-hz = /bits/ 64 <480000000>;
> >> > > +			opp-microvolt = <980000 980000 1300000>;
> >> > > +			clock-latency-ns = <244144>; /* 8 32k periods */
> >> > > +		};
> >> > > +
> >> > > +		opp at 648000000 {
> >> > > +			opp-hz = /bits/ 64 <816000000>;
> >> > > +			opp-microvolt = <1020000 1020000 1300000>;
> >> > > +			clock-latency-ns = <244144>; /* 8 32k periods */
> >> > > +		};
> >> > > +
> >> > > +		opp at 912000000 {
> >> > > +			opp-hz = /bits/ 64 <960000000>;
> >> > > +			opp-microvolt = <1080000 1080000 1300000>;
> >> > > +			clock-latency-ns = <244144>; /* 8 32k periods */
> >> > > +		};
> >> > > +
> >> > > +		opp at 1008000000 {
> >> > > +			opp-hz = /bits/ 64 <1008000000>;
> >> > > +			opp-microvolt = <1140000 1140000 1300000>;
> >> > > +			clock-latency-ns = <244144>; /* 8 32k periods */
> >> > > +		};
> >> > > +	};
> >> > > +
> >> > 
> >> > From your serie, I guess you never actually tested those OPPs on
> >any
> >> > board without SY8113B, right?
> >> 
> >> Yes. But I will test them on an Orange Pi PC (newly got) soon.
> >
> >The orange pi pc also uses the SY8113B.
> 
> I remember in H3 Orange Pi's only One, Lite and Zero uses SY8113B,
> and PC is SY8106A.

Ah, my bad, I confused the two.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170417/516cd3a6/attachment-0001.sig>