[PATCH v3 9/9] ARM: dts: imx6ul-isiot: Add FEC node support

[Jagan Teki]

From: Jagan Teki <jagan at amarulasolutions.com>

Add support for fec1 node on Engicam Is.IoT variant boards.

Cc: Shawn Guo <shawnguo at kernel.org>
Cc: Matteo Lisi <matteo.lisi at engicam.com>
Cc: Michael Trimarchi <michael at amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
Changes for v3:
- none
Changes for v2:
- Newly added patch

 arch/arm/boot/dts/imx6ul-isiot.dtsi | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/imx6ul-isiot.dtsi
index 7e947e5..ccc5477 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/imx6ul-isiot.dtsi
@@ -129,6 +129,24 @@
 	status = "okay";
 };
 
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};
+
 &pwm8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
@@ -159,6 +177,21 @@
 };
 
 &iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA0__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET1_MDC	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x1b0b0
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
-- 
1.9.1