[PATCH] phy: bcm-ns-usb3: split all writes into reg & val pairs

[Kishon Vijay Abraham I]

Hi,

On Sunday 02 April 2017 10:25 PM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal at milecki.pl>
> 
> So far all the PHY initialization was implemented using some totally
> magic values. There was some pattern there but it wasn't clear what is
> it about.
> 
> Thanks to the patch submitted by Broadcom:
> [PATCH 5/6] phy: Add USB3 PHY support for Broadcom NSP SoC
> and the upstream "iproc-mdio" driver we now know there is a MDIO bus
> underneath with PHY(s) and their registers.
> 
> It allows us to clean the driver a bit by making all these values less
> magical. The next step is switching to using a proper MDIO layer.
> 
> Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
> ---
>  drivers/phy/phy-bcm-ns-usb3.c | 69 ++++++++++++++++++++++++++++++-------------
>  1 file changed, 49 insertions(+), 20 deletions(-)
> 
> diff --git a/drivers/phy/phy-bcm-ns-usb3.c b/drivers/phy/phy-bcm-ns-usb3.c
> index f420fa4bebfc..22b5e7047fa6 100644
> --- a/drivers/phy/phy-bcm-ns-usb3.c
> +++ b/drivers/phy/phy-bcm-ns-usb3.c
> @@ -2,6 +2,7 @@
>   * Broadcom Northstar USB 3.0 PHY Driver
>   *
>   * Copyright (C) 2016 Rafał Miłecki <rafal at milecki.pl>
> + * Copyright (C) 2016 Broadcom
>   *
>   * All magic values used for initialization (and related comments) were obtained
>   * from Broadcom's SDK:
> @@ -23,6 +24,23 @@
>  
>  #define BCM_NS_USB3_MII_MNG_TIMEOUT_US	1000	/* usecs */
>  
> +#define BCM_NS_USB3_PHY_BASE_ADDR_REG	0x1f
> +#define BCM_NS_USB3_PHY_PLL30_BLOCK	0x8000
> +#define BCM_NS_USB3_PHY_TX_PMD_BLOCK	0x8040
> +#define BCM_NS_USB3_PHY_PIPE_BLOCK	0x8060
> +
> +/* Registers of PLL30 block */
> +#define BCM_NS_USB3_PLL_CONTROL		0x01
> +#define BCM_NS_USB3_PLLA_CONTROL0	0x0a
> +#define BCM_NS_USB3_PLLA_CONTROL1	0x0b
> +
> +/* Registers of TX PMD block */
> +#define BCM_NS_USB3_TX_PMD_CONTROL1	0x01
> +
> +/* Registers of PIPE block */
> +#define BCM_NS_USB3_LFPS_CMP		0x02
> +#define BCM_NS_USB3_LFPS_DEGLITCH	0x03
> +
>  enum bcm_ns_family {
>  	BCM_NS_UNKNOWN,
>  	BCM_NS_AX,
> @@ -76,8 +94,10 @@ static inline int bcm_ns_usb3_mii_mng_wait_idle(struct bcm_ns_usb3 *usb3)
>  				    usecs_to_jiffies(BCM_NS_USB3_MII_MNG_TIMEOUT_US));
>  }
>  
> -static int bcm_ns_usb3_mii_mng_write32(struct bcm_ns_usb3 *usb3, u32 value)
> +static int bcm_ns_usb3_mdio_phy_write(struct bcm_ns_usb3 *usb3, u16 reg,
> +				      u16 value)
>  {
> +	u32 tmp = 0;
>  	int err;
>  
>  	err = bcm_ns_usb3_mii_mng_wait_idle(usb3);
> @@ -86,7 +106,11 @@ static int bcm_ns_usb3_mii_mng_write32(struct bcm_ns_usb3 *usb3, u32 value)
>  		return err;
>  	}
>  
> -	writel(value, usb3->ccb_mii + BCMA_CCB_MII_MNG_CMD_DATA);
> +	/* TODO: Use a proper MDIO bus layer */

Instead of using this intermediate patch, can we directly convert this to
mdio_driver or you see issues with converting it?

Thanks
Kishon