[PATCH v2 1/2] arm64: dts: rk3399: add support for firefly-rk3399 board
Kever Yang
kever.yang at rock-chips.com
Wed Apr 5 02:33:19 PDT 2017
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral works:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
Not work:
- USB 3.0 HOST, type-C port
- sdio, sd-card
Not test for other peripheral:
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
---
Changes in v2:
- rebase on Heiko's for-next
- using pinctrl binding header definition instead of a number
- other fix by comments from Heiko and Andreas.
arch/arm64/boot/dts/rockchip/Makefile | 1 +
arch/arm64/boot/dts/rockchip/rk3399-firefly.dts | 750 ++++++++++++++++++++++++
2 files changed, 751 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index b5636bb..bcfa53b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
always := $(dtb-y)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
new file mode 100644
index 0000000..d427d40
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
@@ -0,0 +1,750 @@
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+
+/ {
+ model = "Firefly-RK3399 Board";
+ compatible = "firefly,firefly-rk3399", "rockchip,rk3399";
+
+ backlight: backlight {
+ status = "okay";
+ compatible = "pwm-backlight";
+ enable-gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pwms = <&pwm0 0 25000 0>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7
+ 8 9 10 11 12 13 14 15
+ 16 17 18 19 20 21 22 23
+ 24 25 26 27 28 29 30 31
+ 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47
+ 48 49 50 51 52 53 54 55
+ 56 57 58 59 60 61 62 63
+ 64 65 66 67 68 69 70 71
+ 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87
+ 88 89 90 91 92 93 94 95
+ 96 97 98 99 100 101 102 103
+ 104 105 106 107 108 109 110 111
+ 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127
+ 128 129 130 131 132 133 134 135
+ 136 137 138 139 140 141 142 143
+ 144 145 146 147 148 149 150 151
+ 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167
+ 168 169 170 171 172 173 174 175
+ 176 177 178 179 180 181 182 183
+ 184 185 186 187 188 189 190 191
+ 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207
+ 208 209 210 211 212 213 214 215
+ 216 217 218 219 220 221 222 223
+ 224 225 226 227 228 229 230 231
+ 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247
+ 248 249 250 251 252 253 254 255>;
+ default-brightness-level = <200>;
+ };
+
+ clkin_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "clkin_gmac";
+ #clock-cells = <0>;
+ };
+
+ rt5640-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "rockchip,rt5640-codec";
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Mic Jack", "MICBIAS1",
+ "IN1P", "Mic Jack",
+ "Headphone Jack", "HPOL",
+ "Headphone Jack", "HPOR";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rt5640>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc3v3_pcie: vcc3v3-pcie-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_drv>;
+ regulator-name = "vcc3v3_pcie";
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 1>;
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ /* for rockchip boot on */
+ rockchip,pwm_id= <2>;
+ rockchip,pwm_voltage = <1000000>;
+ };
+
+ vccadc_ref: vccadc-ref {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_RMII_SRC>;
+ assigned-clock-parents = <&clkin_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x28>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <168>;
+ i2c-scl-falling-time-ns = <4>;
+ clock-frequency = <400000>;
+
+ vdd_cpu_b: pmic at 40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ vin-supply = <&vcc5v0_sys>;
+ regulator-compatible = "fan53555-reg";
+ regulator-name = "vdd_cpu_b";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ vsel-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+ fcs,suspend-voltage-selector = <0>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-state = <3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: syr828 at 41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ vin-supply = <&vcc5v0_sys>;
+ regulator-compatible = "fan53555-reg";
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-state = <3>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk808: pmic at 1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ vcc10-supply = <&vcc3v3_sys>;
+ vcc11-supply = <&vcc3v3_sys>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc1v8_pmu>;
+
+ regulators {
+ vdd_center: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_center";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-name = "vdd_cpu_l";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v0_tp: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc3v0_tp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sd: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcca3v0_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc_1v5";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_3v0";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <300>;
+ i2c-scl-falling-time-ns = <15>;
+
+ gsl3673: gsl3673 at 40 {
+ compatible = "GSL,GSL3673";
+ reg = <0x40>;
+ screen_max_x = <1536>;
+ screen_max_y = <2048>;
+ irq_gpio_number = <&gpio1 RK_PC4 IRQ_TYPE_LEVEL_LOW>;
+ rst_gpio_number = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
+ };
+
+ rt5640: rt5640 at 1c {
+ #sound-dai-cells = <0>;
+ compatible = "realtek,rt5640";
+ reg = <0x1c>;
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ clock-names = "mclk";
+ realtek,in1-differential;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rt5640_hpcon>;
+ hp-con-gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+ io-channels = <&saradc 4>;
+ hp-det-adc-value = <500>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <450>;
+ i2c-scl-falling-time-ns = <15>;
+};
+
+&i2c4 {
+ status = "okay";
+ i2c-scl-rising-time-ns = <600>;
+ i2c-scl-falling-time-ns = <20>;
+
+ fusb0: fusb30x at 22 {
+ compatible = "fairchild,fusb302";
+ reg = <0x22>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int>;
+ int-n-gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
+ vbus-5v-gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ mpu6500 at 68 {
+ status = "okay";
+ compatible = "invensense,mpu6500";
+ reg = <0x68>;
+ irq-gpio = <&gpio1 RK_PC6 IRQ_TYPE_EDGE_RISING>;
+ mpu-int_config = <0x10>;
+ mpu-level_shifter = <0>;
+ mpu-orientation = <0 1 0 1 0 0 0 0 1>;
+ orientation-x= <1>;
+ orientation-y= <0>;
+ orientation-z= <0>;
+ mpu-debug = <1>;
+ };
+};
+
+&i2s0 {
+ status = "okay";
+ rockchip,i2s-broken-burst-len;
+ rockchip,playback-channels = <8>;
+ rockchip,capture-channels = <8>;
+ #sound-dai-cells = <0>;
+};
+
+&i2s1 {
+ status = "okay";
+ rockchip,i2s-broken-burst-len;
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
+ #sound-dai-cells = <0>;
+};
+
+&i2s2 {
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+&io_domains {
+ status = "okay";
+
+ bt656-supply = <&vcc1v8_dvp>;
+ audio-supply = <&vcca1v8_codec>;
+ sdmmc-supply = <&vcc_sd>;
+ gpio1830-supply = <&vcc_3v0>;
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
+ num-lanes = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn>;
+ status = "okay";
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmu1830-supply = <&vcc_3v0>;
+};
+
+&pinctrl {
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ lcd-panel {
+ lcd_panel_reset: lcd-panel-reset {
+ rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pcie {
+ pcie_drv: pcie-drv {
+ rockchip,pins =
+ <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ pcie_3g_drv: pcie-3g-drv {
+ rockchip,pins =
+ <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pmic {
+ vsel1_gpio: vsel1-gpio {
+ rockchip,pins =
+ <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ vsel2_gpio: vsel2-gpio {
+ rockchip,pins =
+ <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins =
+ <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wireless-bluetooth {
+ uart0_gpios: uart0-gpios {
+ rockchip,pins =
+ <2 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ rt5640 {
+ rt5640_hpcon: rt5640-hpcon {
+ rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins =
+ <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins =
+ <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ fusb30x {
+ fusb0_int: fusb0-int {
+ rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vccadc_ref>;
+};
+
+&sdhci {
+ bus-width = <8>;
+ keep-power-in-suspend;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
+ status = "okay";
+ supports-emmc;
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+ extcon = <&fusb0>;
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list